emax tinyhawk 2 freestyle camera upgrade, caddx baby ratel 2
HTML-код
- Опубликовано: 16 янв 2022
- caddx baby ratel 2 camera upgrade for emax tinyhawk 2 freestyle.
specs,installation guide, comparisson video flights and summery.
awesome little camera.see my full experience.
tpu parts and prinying service 3d-aqua on ebay
www.ebay.co.uk/usr/3d-aqua?_t...
caddx bsby ratel 2 camera
hobby rc
www.hobbyrc.co.uk/caddx-baby-...
unmanned tech
www.unmannedtechshop.co.uk/pr...
CRIMP 3 PIN CAMERA CONNECTORS AND PLUG
FROM HOBBY KING
hobbyking.com/en_us/jst-sh-1-...
3 PIN JST CONNECTORS FOR BOARD
UNMANNED TECH
www.unmannedtechshop.co.uk/pr...
pre wired jst cable to fit board plug
unmanned tech
www.unmannedtechshop.co.uk/pr...
15mm m2 alloy upstands ebay
www.ebay.co.uk/itm/3338177757...
landing pad soft motor mounts thingyverse
www.thingiverse.com/thing:382...
tbs crossfire nano rx
drone authority
www.droneauthority.co.uk/prod...
minimortal antenna drone authority
www.droneauthority.co.uk/prod...
foxeer micro lollipop antenna select ufl
unmanned tech
www.unmannedtechshop.co.uk/pr...
xt30 battery connector
drone authority
www.droneauthority.co.uk/prod...
flywoo arm led 4mm
www.kkelkomet.com/index.php?m...
motors
www.buzzflyer.co.uk/EMAX-Tiny...
propellors
www.unmannedtechshop.co.uk/pr...
Just when you thought it was all upgraded. Those cameras look day and night difference. Awesome. Good little RIp bro🤙🏼 lookin forward to next one 👍🏼👍🏼
Your a very clever guy it took me ages to attach zip ties on my tinyhawk.
Its so much better! Fancy it I do 😁
If anyone has the problem of having video feed but no OSD then what might be the problem is this: You may need to go into the OSD tab of betaflight and set the format as auto. It is probably on NTSC or PAL and sometimes one or the other will cause some cameras to not allow OSD overlay. Just put it on auto and let it choose, then most likely it will work! I had this problem and someone said to do that and it worked so i just wanted to share this advise to anyone that needs it. :)
Oh nice. I just ordered a runcam nano 4 to replace the stock tinyhawk 2 freestyle camera. Hopefully process of replacing it isn't too difficult, aha
Connector is a real PITA. No pads to solder the cam to there?
I've been meaning to do this for a while, I use a ratel 2 on my nazgul and I much prefer the look on it compared to my tiny hawk freestyle
The runcam nano 2 is actually a decent sunny day camera. It turns out though that it's very temperamental about the components running it and then the goggles receiving everything as well. It seems to be due to the oversaturation the sensor pulls in. Conditions have to be met perfectly to get a good picture out of it and if you want a night time camera, definitely swap it out for something else with the different lux rating. At the end of the day the baby ratel2 seems to be better in just about every way from the research I've done. I'm not sure if the latency is higher on the baby ratel2 or not at around 20 milliseconds. Does anyone know if the latency on The run cam nano 2 is less? Either way 20 milliseconds is plenty adequate for freestyle, maybe not so much for racing though. I'm currently in the process of installing the baby ratel 2 in my GEPRC Phantom and moving the stock caddx ant that comes with it, over into my TH Freestyle2 because even the caddx ant is better than the nano 2 for the type of flying I prefer.
Instead of building the new cable with the right video/pwr/gnd order at both ends, you mention the alternative is to just cut the two cables and solder them together to create one with the right ends that work on the caddx and TH2 FC. Is there a reason why you did not do that (other that the state it leaves the Runcam Nano 2 in)? Any video quality loss with the cut/solder method? Thanks!
what battry would u recomend me to buy on amazon
Globe might be global shutter?
Clearly the Run Cam nano sucks.