mine has the 11 flash fault, dud fan. Tested it with 12v, nil op, put one of the others on that harness and it works, ordered one from china on ebay $20 and waiting for it to rock up. Hopefully that sorts the problem. Interestingly resitence testing the dud fan shows it is not that different to a good one and it spins freely. Would be nice to know what fails in them.
Hallo, I have Panasonic plasma 65 st60. When I turn it on green light flashes six times,but works without problems. Does it have anything wrong?After watch your video i will tighten the screws. Thanks!
Hi i managed to fix my tv but used the original bolts. After a clean and back panel alignment (sound vibrations) i checked the screws and some of them actually moved a little after tightening them again. Do you know the screw size of these boards so i can order new ones with springs and washers to make this not fail again in the near future? They seem like M3
Hi, As a TV repair specialist, where do you buy your igbt for Panasonic plasmas (30f131, ....) which are now obsoleted since a Long time and no more in stock at reliable providers (mouser, digikey, rs, ...). eBay and Ali express are mostly fakes and i don't know which seller to trust ! ... Coul'd you share an advice ?
Great video Allen. I have a txp42gt30b which went click and turned off, 7 red flashes. My Y sus board is all in one with the buffer board. I had a very loose screw at the top on the set. Also no continuity across one of the power boards fuses. Did you do a video for the 42”? Do you think I may have to change both boards? £200 if I do which I dont want to waste if it doesnt fix it.
Hi Allen. I have the 7 blink code on my plasma 42 incher. Model TH-P42S10D. It however works for 5 minutes or so and then goes into a 7 blink standby. What should I do? I am handy with a screwdriver and other basic stuff. Please advice. Thanks.
@@allenfleckney5969 checked all the screws after opening the tv. Cleaned the power supply board, and all boards in general. Reassembled and still the same problem crops up after 5 minutes or so. Next what could I do?
@@allenfleckney5969 since I only cleaned it and did no checking with a voltage meter, what should I do next? Anything else? Or is it a trip to the tech? Where are you based? Thanks.
Hi Laurence. Shouldn’t be £200 ? Yes your fets on the board would have blown. Plus the IC’s. Also 2 transistors and a fuse on the power supply short out sometimes. Plenty of repair agents on eBay that will sort this for you.
Nice video. I have the Panasonic TC-P50GT30. Had the 7 blinking lights. Board TNPA5335 was repaired 9/24/2020. Received board 9/29/2020 and installed it. Now the TV is blinking 8 lights. Any advice?
mine has the 11 flash fault, dud fan. Tested it with 12v, nil op, put one of the others on that harness and it works, ordered one from china on ebay $20 and waiting for it to rock up. Hopefully that sorts the problem. Interestingly resitence testing the dud fan shows it is not that different to a good one and it spins freely. Would be nice to know what fails in them.
Hi Steve. If it’s 7 blinks yes. Check gor shorts on those fets. If it’s not the mosfets on the y sus it could be a buffer board.
Hallo, I have Panasonic plasma 65 st60. When I turn it on green light flashes six times,but works without problems. Does it have anything wrong?After watch your video i will tighten the screws. Thanks!
Hi i managed to fix my tv but used the original bolts. After a clean and back panel alignment (sound vibrations) i checked the screws and some of them actually moved a little after tightening them again. Do you know the screw size of these boards so i can order new ones with springs and washers to make this not fail again in the near future? They seem like M3
Hi Allen,
Would a similar fix be applied to the VT50? Specifically the 65" Panasonic Plasma?
Hi,
As a TV repair specialist, where do you buy your igbt for Panasonic plasmas (30f131, ....) which are now obsoleted since a Long time and no more in stock at reliable providers (mouser, digikey, rs, ...). eBay and Ali express are mostly fakes and i don't know which seller to trust ! ...
Coul'd you share an advice ?
Great video Allen. I have a txp42gt30b which went click and turned off, 7 red flashes. My Y sus board is all in one with the buffer board. I had a very loose screw at the top on the set. Also no continuity across one of the power boards fuses. Did you do a video for the 42”? Do you think I may have to change both boards? £200 if I do which I dont want to waste if it doesnt fix it.
Hi Allen. I have the 7 blink code on my plasma 42 incher. Model TH-P42S10D. It however works for 5 minutes or so and then goes into a 7 blink standby. What should I do? I am handy with a screwdriver and other basic stuff. Please advice. Thanks.
Check all screws in all boards are tight. You may get lucky
@@allenfleckney5969 checked all the screws after opening the tv. Cleaned the power supply board, and all boards in general. Reassembled and still the same problem crops up after 5 minutes or so. Next what could I do?
If the screws are tight and there are no shorts on the Y sus. Then it’s usually the main board.
@@allenfleckney5969 since I only cleaned it and did no checking with a voltage meter, what should I do next? Anything else? Or is it a trip to the tech? Where are you based? Thanks.
Hi Laurence. Shouldn’t be £200 ? Yes your fets on the board would have blown. Plus the IC’s. Also 2 transistors and a fuse on the power supply short out sometimes. Plenty of repair agents on eBay that will sort this for you.
Nice video. I have the Panasonic TC-P50GT30. Had the 7 blinking lights. Board TNPA5335 was repaired 9/24/2020. Received board 9/29/2020 and installed it. Now the TV is blinking 8 lights. Any advice?
Hi John 8 blinks is usually the X- Z or as panasonic call it the SS board. It’s the right hand side one.
@@allenfleckney5969 that's the TNPA 5331 on my tv. Will remove it and get it repaired or replaced. Thanks.
Yes the SS board. Make sure you match the 2 corresponding letters . Maybe AG etc.
@@allenfleckney5969I noticed your TV looks the same as mine. But, I noticed you have 4 fans and on the back cover it says UK / Ireland model.
@@allenfleckney5969 Also, I have 2 fans and they didn't turn on.
I could morning how can I get in touch of you
I have the 50-inch v20 3d one it's a nice TV.
After changing the components the screen has two horizontal lines
Great work thank you.
Jadi 7 blink apa yang rusak sir? Dan apa saja yang di ganti? Thanks atas video nya...
Nice work good fix
Ok wil try to fix my tv because no one can match the plasma picture quality
Ahora tiene el mismo plasma 50" tv. 6 blink
I want to Lane more from me and I want you to be mine teacher on the Panasonic TV set
Panasoni plasma 50" 6 blinkin
Hello, How can I contact you by message or e-mail ? Regards
good job ....
Foks for camera parts chenge
I must try fixing mine
Hello friend I have a problem so you can help me
Hello friend I have a problem so you can help me
Tengo plasma 50" tiene 10 blinki
10 blinks usually power board