I love fluid film!! My 2007 ford van has no rust thanks to fluid film. I filled all my body panels and undercoated with it. Been using it for 5 years now. Use it on all my vehicles. Thank you fluid film!!
I remember the first time I used FF, I thought it was goopy, thick and messy. Now I use it every week in the garage. I found a plastic bristle paint brush as my go to for applying the stuff, spray some into the brush and apply, puts a nice thin transparent layer down.
My preferred means of application is with a brush for the exterior surfaces. It allows me to avoid the mess of overspray and waste with spraying in general.
I have the kellsport pro kit and love it! I need that spray gun emerging at 2:40 to cut down on application times and still doing a quality job. What a great undercoat. Love fluid film.
That's an airless sprayer probably for line striping parking lots. They pressurize the paint to 3100 psi. GRACO makes them. They can be costly. they have all different tips for spray width and volume. Good thing about these when they are spraying paint in a parking lot they will remove alot of dust while it's spraying . They blast pretty well but are expensive.
I love this stuff, easy to use and apply! I always have it on hand for touch ups. Use it on my 2000 Dodge Ram 2500, 2000 Beetle and a 1998 Honda Passport in NE Ohio, doing the job!
14s dont have grommets, ford used clear tape on the inside of the rocker. Getting it to the cab corners is tricky, theres a pinkie sized hole you can feel for through the last hole that goes to outside of corner, if you really want to get to inside of corner, and i would, drill an access hole on the backside. Brake light leaks so get a decent new gasket if not to late and sunroof drains into them also. Had to weld a patch on driver side but got lucky on other side. And that foam in the wheel wells needs to be removed then soakm good. Its not spongy but still holds moisture, i put some in a glass of water and it wound up staying wet for a while.
@ 0:39, what type of undercoating paints does Fluid Film soften? I was considering purchasing the Fluid Film Pro kit with compressed air sprayer and two gallons of product - mostly because up until now I have been using the aerosol spray cans under my vehicle - 2005 Jeep Grand Cherokee.
Hello, Any soft porous materials fluid film may penetrate. it is designed to penetrate into metal pores to stop rust and will do the same to a paint. we have only had issues with aftermarket undercoating paint, rubberized undercoatings and GMC soft wax coatings so far but encourage our customers to try a small test section before coating the entire underside. if you have any other questions feel free to ask
I had a CRC application from Toyota, after they had frame rot problems and feel fluid film keeps the crc from hardening, which keeps out water/oxygen. ~ Great stuff!
This year I used fluid film for the summer on my 2010 titan and it worked great! I'm thinking about doing fluid film then black undercoating afterwards for winter
@@fluidfilmusa Awesome! I've been using fluid film for the better part of the last decade and it's great what it does. If you ever wanted me to feature one of your products on the channel, I'd be happy to do so :)
Fluid film can be applied directly to a tightly adhering rusted surface. If there is loose flake we recommend removing that so the product can penetrate to the base and stop it from progressing. We recommend applying our film directly to the rust or clean metal as converters can encapsulate rust and progress it.
As long as the frame is relatively clean (no caked on dirt) and not wet (our product can be applied to a damp surface) it is good to go! Most customers do a drive through wash a day or two before coatings.
Once this is applied, can you take the car through a car wash on those warmer winter days to wash the salts and crud off? Will the fluid film last or just get washed off first time?
@@BaptistJoshua hey it worked awesome for me. I used about 4 cans on the underbody, and then one can for the doors and body panels. Totally worth it. I found once a year was enough. But then I moved to Arizona so undercoating is a thing of the past for me now 😎😎👊
@@QuintTheSharker Nice. Thank you. I am trying to figure out what non-oil resistant rubber they say not to use it on would be. Seems like vehicular rubber would be oil-resistant.
@@BaptistJoshua I get that. I was worried about it too. Depending on your vehicle, maybe you wouldn’t have to worry about it. My big thing was if the rust proofing degraded some rubber trim or seals over time, those parts are cheap to replace. But once the body starts to rust, the clock is ticking. For what it’s worth, I coated everything I could inside and out and I’ve never had any rubber fall apart on me and I started using fluid film 5 years ago.
@@QuintTheSharker Fluid Film responded to me by e-mail. They said: *_Almost all rubbers are oil-resistant. The main areas we see and warn about are weather stripping on automotive doors. Bushings, boots, frame spacers and motor mounts are almost always oil-resistant due to their exposure._*
Love love love love FF. I use it underneath my mower decks and to lubricate almost anything. Spraying directly on batteries is ok? What about 7 pin trailer connectors? I've seen people use FF instead of Dialectic grease. I'm about to do my winter clean and seal on truck, dump trailer, and outdoor power equipment. Anyone have any bad experience using it with mowers, saws, or trimmers? Wondering if it could harm certain plants...
This stuff is awesome. You really need the official FF application gun and 360 wand to do it right. One gallon has lasted me three years so far and that's with two apps a year in my SuperCrew F150. Just remember, a little goes a long way.
😁 My first application on my 2017 Super Duty crew cab 8' box. I used a hole gallon. Then 2 spray cans with small 360° tube for doors tailgate and hood. Mite be a little excessive but 2 years later looks perfect. The white Rancho shocks have 0 rust. They rust if you look at them wrong 😉. I apply twice a year.
Ghost- Face basically just the disk brakes and exhaust components. If there is any overspray on these areas it can be removed with a rag and a solvent like brake part cleaner.
Great product it seems but i have a question, mud and dirt usually sticks in my cars wheel wells. Does pressure washing after applying the fluid film remove it, what should i do?
Hi, Guys what's the correct name for the 360-degree wand and the red spray nozzle attachment being used at 2:35min? ============================================ or =========================================== ===================== The full equipment setup used.. I do have a compressor =======================
Hi Carlo, we offer a undercoating kit with the part number FFSG similar to the setup used with the nozzles here. This shop also used an airless(electric) paint sprayer which was a Graco magnum Pro LTS 170 but any airless system should work.
Fluid Film is designed to penetrate into the pores of the metal and can soften some existing coatings or be used to re-hydrate them if the salt/brine has dried it. Depending on the condition of the Krown coating you may just want to apply our film to the suspension components, inside rocker panels, doors, and other areas away from the Krown coating until it begins to crack and fail.
Fluid Film is a wet coating and can get a surface dusting of dirt. As the product is solvent free it does not get tacky like other wet coatings and the dirt often can be rinsed off without removing the coating.
Hello, the tips put out a good amount of product so it can creep and self level. The spray is consistent and can be seen at the opening of the access points to assess if another pass is needed.
@@johnkim3658 hi John, Fluid film is safe on suspension components including shocks. Our product also does not harm a finished paint with a clear coat if there is overspray. Simply wash off the overspray with a degreaser and water.
Want to try it. What sprayers is he using? I like the fan tip type around the middle of the video that he used but don't know what it where to get it. Any help would be appreciated.
Ickes78 thank you for reaching out. the shop used a combination of an undercoating gun (shots with the wands) and a Wagner airless (electric powered) paint gun for the large chassis coating. Any airless paint gun should be sufficient for applying the product as we have used a number of different airless systems in the past. You can email us at info@fluid-Film.com if you want to ask about a specific gun.
Can you apply Fluid-Film over a dry layer of POR-15 and would washing the undercarriage with a power washer weekly over the winter cause the Fluid-Film to come off? Thanks !
Hi Alvin, Thank you for your interest in FLUID FILM®. You can apply FLUID FILM® over POR-15 but it in not necessary to paint the surface because FLUID FILM® was designed to be applied over bare metal. We do not recommend pressure washing the undercarriage once FLUID FILM® is applied. FLUID FILM® is a wet coating and spraying it with a pressure washer will start to remove the product. If you want to clean the undercarriage you can use regular hose pressure. FLUID FILM® is not water soluble so any debris on top of the product will wash off and the product will stay behind. If you have any other questions please let us know. Best Regards, -FLUID FILM® Team
The one used in the video is a Graco Magnum Pro LTS 170. Most standard electric paint sprayers can be used to suck the product directly from the cans, pails and drums.
Fluid Film is solvent free so it can be used on oil-resistant rubbers such as bushings, motor mounts, brake lines, and cv boots. The main areas to avoid are disc brakes (our product is a lubricant also) and the exhaust components (high temps will cause the product to smoke off). If you accidentally coat the brakes some brake part cleaner and a rag will remove it. For the exhaust wiping the excess with a rag is fine. We also recommend avoiding the weather stripping inside doors as it is typically foam or an untreated rubber. As long as the product is wiped off in a few minutes it should not cause any issues.
This is a fantastic use for our product. As a wet coating it can be applied directly to a rusted surface (we recommend removing the loose scale if present) as it will soak into the rust and penetrate to the base. Effectively stopping the progression with minimal surface prep. We also have a black version of the film to both cover and treat the rust.
As a wet coating. Fluid film is ready to go as soon as it is applied. If you’re going to be driving in wet conditions directly after an application you may want to wait 10-15 mins for it to fully settle before driving.
What is the brand of large coverage spray gun used? Not the one with the canister but the one fed directly by hose? Been spraying this stuff for 7 years in Vermont, do about 40 cars a year, works AWESOME.
We offer an undercoating kit through Napa Auto and O’reilleys with a part number FFSG. Other than that most airless (electric) paint sprayers will work. Gracie and Lemmers both have a line of undercoating systems to handle our products.
We have another video for mixing thick product. Fluid Film is thixotropic and can body up when in a container. We do this so once applied it resists wash off easier. Mixing the product well and getting not to a room temperature is usually best.
@@fluidfilmusa Thanks for the quick response, friend showed me that his can was also same texture. I was not aware I could apply it with a Shutz gun. I just spoon it into an empty undercoating container and all is working great.
Our product has a similar viscosity to a house paint when we’ll mixed and can be applied directly with an airless (electric) paint sprayer directly from the gallon, 5 gallon, or 55 gallon drum. Any electric paint sprayer should work.
@@fluidfilmusa Yes...But can you please find out which setup are you using in this video? and let us know. I dont recognize that gun with the wide fan tip and its working like a fire hose, not all airless paint guns will spray fluid film this well, ...Love the product..NEED THIS GUN SETUP! ***EDIT...gun appears to be a Graco magnum airless
Hey, I love Fluid Film. Are there any issues with FF getting onto the brakes? I usually cover the drum/disc with newspaper to avoid overspray. I haven't seen anyone else do this though and notice in the video they get sprayed directly?
As our product is a lubricant we don’t recommend applying it to the brakes. In the case of overspray you can use brake part cleaner and a rag to remove the film. Most shops will bag or cover the brakes so they can coat the lines as close as possible.
Hi Bob, as long as the chassis is relatively clean it should be good to go. Washing is only needed if there is caked on dirt or mud that prevents the film from soaking into the metal
Hi Andy, Thank you for your interest in FLUID FILM®! Yes, we recommend not using high pressure undercarriage washes while FLUID FILM® is applied. If you want to rinse the chassis, simply use regular hose pressure. If you have any other questions please let us know! Best Regards, -FLUID FILM® Team
@@joshuarivera2478 Hard coatings typically trap rust and cover issues. it also doesnt allow the product to penetrate into pinch welds and seams like a wet coating which is where much of the protection is needed.
Yes! The advantage of the wet coating is that is soaks into existing rust and penetrates to the clean base metal preventing it from progressing. We do recommend removing loose scale first and if the rust is thicker you may need a second coat.
Had my friend detail my 1997 truck that has a perfect frame. He took the liberty of spraying 3 cans of CREST SUPER RUBBER COAT on my frame. How can I undo this??
Most rubber coatings are not oil resistant. Spraying FF and leaving it on the rubberized coating can soften it and make it easier to remove. Once removed you can apply Fluid Film.
Hi Brandon, As a wet coating, Fluid Film does not need to be washed after a storm. High pressure sprayers and detergents can shorten the life of the product so we recommend against it. If you would like to rinse the vehicle with standard hose pressure that works but isn’t necessary. You can also still use drive through car washes without selecting the undercarriage spray.
With all that spraying, you're bound to have a little overspray on your disc brakes. (I speak from experience) because my rear brakes squeak under load, is there a way to clean the stuff off? I've already tried brake cleaner.
@@DEADIKATED yes! When Fluid Film is applied directly to a rusted surface, it penetrates to the clean base metal and prevents the rust from progressing and softens the existing rust. We do recommend removing loose flaking rust before application to ensure the product can penetrate the the base. If the rust is extremely thick a second coat may be necessary.
@@fluidfilmusa Thanks! I just Fluid Filmed my car last week using the Husky 4.5 gallon "silent" compressor and a Wool Wax pro gun kit running at 85 psi. The compressor ran a lot but kept up! Pro gun is the best way to minimize time lying under the car. The spray cans were good for touching up spots I missed without having to drag the compressor out.
I use both Fluid Film and WoolWax. Spray Fluid Film on first to get maximum creep, preferably in summer. Then I come a month later and put WoolWax over the top. Won’t wash off.
you guys mentioned to spray it on suspension components in the video. Is it safe? Cuz, some UCAs and coilovers have teflon coating. Can this be damaged due to Fluid film? Also can CV boots, Bushing and rubber from suspension components be safe?
mgltacoma Fluid Film will not harm oil-resistant rubbers like cv-boots, motor mounts and almost any other rubber underneath a vehicle. As far as the Teflon goes, we have not done specific testing but know our product is used all over the off road racing for protection and lubrication of suspension components. Along with our daily commuters we have had no issues.
Teflon is the trade-name of PTFE. PTFE or Poly(TetraFluoroEthylene) is not able to be dissolved by any common solvents and is highly chemically resistant.
Is fluid film safe on rocker panel plugs? They are rubber, I heard fluid film messes up rubber. I have a Tacoma that has rubber plugs at the bottom of the rocker panels.
Fluid Film doesn’t harm oil resistant rubbers. We have been applied inside rocker panels without issue for the last 20 years. The main area we have trouble is door seal gaskets. As long as the overspray is wiped off there should be no issue
sponge bob Hi Bob, A quick rinse is all that is needed. Fluid Film can be applied to a damp surface but the dryer the better. A leaf blower or air compressor can be used to dry the undercarriage quickly
Is there a difference between what your using in the video and the spray cans of fluid film, because I just got a couple cans and they spray out as a clear runny liquid, both the regular and the black
Thanks for your interest in FLUID FILM®! One of our East Coast distributors makes and manufacturers that gun and bottle. Their company name is Kellsport Products and their website is: kellsportproducts.com
Hello, I recently took my truck to get this service at an authorized shop. Upon picking it up and inspection, the job had been done miserably. Anyhow, who can I reach out to? I'd like to share a video clip. Thanks.
Hi, thank you for reaching out and we are sorry to hear this. All of the shops are independent locations that use our products. We would still be happy to talk to you about it. You can reach out via info@fluid-film.com
Nothing that gets over 220degrees but it can be applied to a number of areas such as forks, frame, chain, bolts, and areas where rust has started to form.
Fluid film can be applied over an existing rust as it soaks into the rust and penetrates to the base clean metal. We do recommend removing any loose scale before application to ensure the product can be absorbed to the base.
How often should you reapply to places like wheel wells and rockers as those get the highest wet areas due to kicking up rain, snow and salt? Driving over 60 miles on the highway daily would more than likely wash the Fluid Film fairly quickly.
You might need to touch it up once or twice a winter for those high traffic areas. There is typically a good amount in the pores of the metal to last a full season but depending on conditions and usage touch ups are sometimes nescessary.
Fluid Film does not damage oil-resistant runners so bushings, cv-boots and other components under the vehicle should be fine. Weather stripping on doors is typically the only rubber to look out for. If there is overspray you can wipe it off with a rag.
If you choose to use an airless sprayer to apply the FF product how do you clean the lines of your sprayer and pump? Also will FF effect any of the internals of the sprayer? I want to still use my airless sprayer to spray latex paint.
Nathan Hoover Hot water with a degreaser like dawn or simple green run through the lines will clear it. Then rinse with water through the line. Thank you 😊
Cleaner is better. We mainly recommend washing so the product can reach the metal without being absorbed by mud. As a wet coating, even if there is a bit of salt residue our product doesn’t encapsulate it like a hard coating.
We sell a kit on Amazon, or available through NAPA Auto or Oreilleys. The part number is “FFSG” and requires a compressor. Fluid film can also be applied with an airless paint sprayer as it has a similar viscosity to a house paint when well mixed and at a room temperature.
DO YOU NOT NEED TO MASK THE VEHICLE? what if it gets on the paint? whats best to use for cleanup on painted surfaces and the gun afterwards? Looking to offer this service to my customers. I do paint work and detailing.
Fluid Film contains no solvents, silicone or Teflon so it is body shop safe. Our product does not harm a finished paint and can be removed by washing with warm water a pressure washer and a degreaser. Warm water and dish soap can be used to clean the gun if it will not be used for a longer period of time. If you would like more information about becoming an undercoater send us an email to sales@fluid-Film.com and we can further assist you.
Eric from SMA (South Main Auto) - in Avoca NY , loves this stuff. He got me on to it.
Same. He should probably get free fluid film for life. Before him I'd never heard of it.
Yep, me too
Just binge watched his channel and brought me here hahahah
ditto
@@fisqual ya same here, now I’m addicted to the stuff
I love fluid film!! My 2007 ford van has no rust thanks to fluid film. I filled all my body panels and undercoated with it. Been using it for 5 years now. Use it on all my vehicles. Thank you fluid film!!
Steve Grant Thank you!
How do you apply it? From can or spray gun?
@@fluidfilmusa can i apply is straight from bottle? Or what is recommended
Fred ticoman. Both the aerosol cans and the bulk sprayed through a gun work well.
In which State did you live?
FluidFilm is one of the greatest things invented by man! I love the stuff!!!
Thank you!
Applied to my new truck this fall. So far it’s been holding up through the New York winter. Will reapply in spring. Looks perfect thus far.
Thank you!
I can hardly watch the guy doing it without goggles or safety glasses. I always get something in my eyes whenever under car and looking up.
Not harmful, you can eat it
This stuff is great, my truck gets about 10 spray cans every fall, still looks new underneath
ncurc 97 Thank you! We are glad we can help.
holy shit 10 cans? i just did my corolla with about 3/4 of a can
@@fishertech I do an entire first gen tacoma with like 1 and a half cans max
I use 4 cans on a full size truck…
@@fishertech that will just wash off
I remember the first time I used FF, I thought it was goopy, thick and messy. Now I use it every week in the garage. I found a plastic bristle paint brush as my go to for applying the stuff, spray some into the brush and apply, puts a nice thin transparent layer down.
49s13 thank you!
My preferred means of application is with a brush for the exterior surfaces. It allows me to avoid the mess of overspray and waste with spraying in general.
I love huffing my fluid film while applying it to my truck
I have the kellsport pro kit and love it! I need that spray gun emerging at 2:40 to cut down on application times and still doing a quality job. What a great undercoat. Love fluid film.
That's an airless sprayer probably for line striping parking lots. They pressurize the paint to 3100 psi. GRACO makes them. They can be costly. they have all different tips for spray width and volume. Good thing about these when they are spraying paint in a parking lot they will remove alot of dust while it's spraying . They blast pretty well but are expensive.
I love this stuff, easy to use and apply! I always have it on hand for touch ups. Use it on my 2000 Dodge Ram 2500, 2000 Beetle and a 1998 Honda Passport in NE Ohio, doing the job!
Dave Kana Thank you!
FLUID FILM® 🧨, it’s the bomb! Been using it for years!!
love me some FF this stuff is awesome. been using it for the last few years. buy it by the case in the spray cans.
Curious why this isn't done at the factory?
rust means part replacement which means more money for factories, dealers, mechanics, and manufacturers
After using this product with the Kelly Sport kit, I would highly recommend using a respiratory and safety glasses too. ~ Great product.
02markcal Thank you!
14s dont have grommets, ford used clear tape on the inside of the rocker. Getting it to the cab corners is tricky, theres a pinkie sized hole you can feel for through the last hole that goes to outside of corner, if you really want to get to inside of corner, and i would, drill an access hole on the backside. Brake light leaks so get a decent new gasket if not to late and sunroof drains into them also. Had to weld a patch on driver side but got lucky on other side. And that foam in the wheel wells needs to be removed then soakm good. Its not spongy but still holds moisture, i put some in a glass of water and it wound up staying wet for a while.
So, without mask, glasses, gloves... Does it heal as well lungs and eyes?
Fluid film is non-hazardous/non-toxic. That being said any time you are atomizing a product a dust mask/ safety glasses can be used.
I think I’m going to mark the holes with a paint pencil so I know where I’ve applied product
cleans out the iris too
@ 0:39, what type of undercoating paints does Fluid Film soften? I was considering purchasing the Fluid Film Pro kit with compressed air sprayer and two gallons of product - mostly because up until now I have been using the aerosol spray cans under my vehicle - 2005 Jeep Grand Cherokee.
Hello,
Any soft porous materials fluid film may penetrate. it is designed to penetrate into metal pores to stop rust and will do the same to a paint. we have only had issues with aftermarket undercoating paint, rubberized undercoatings and GMC soft wax coatings so far but encourage our customers to try a small test section before coating the entire underside.
if you have any other questions feel free to ask
I had a CRC application from Toyota, after they had frame rot problems and feel fluid film keeps the crc from hardening, which keeps out water/oxygen. ~ Great stuff!
This year I used fluid film for the summer on my 2010 titan and it worked great! I'm thinking about doing fluid film then black undercoating afterwards for winter
Thank you! Yes the black has been great for both protection and bringing a clean look to the undercarriage.
Hey Fluid Film...a whole bunch of people are watching my video on fluid film after seeing yours :) Cool to see.
Thank you! Just watched the video and appreciate you using our product!
@@fluidfilmusa Awesome! I've been using fluid film for the better part of the last decade and it's great what it does. If you ever wanted me to feature one of your products on the channel, I'd be happy to do so :)
What should you do if there's existing rust? Sand it off? Apply rust converter first? Just apply over little rust spots?
Fluid film can be applied directly to a tightly adhering rusted surface. If there is loose flake we recommend removing that so the product can penetrate to the base and stop it from progressing. We recommend applying our film directly to the rust or clean metal as converters can encapsulate rust and progress it.
Maybe I missed it, but shouldn't the vehicle be thoroughly washed and dried prior to application?
As long as the frame is relatively clean (no caked on dirt) and not wet (our product can be applied to a damp surface) it is good to go! Most customers do a drive through wash a day or two before coatings.
The new fluid film black is a game changer!
Thank you!
Once this is applied, can you take the car through a car wash on those warmer winter days to wash the salts and crud off? Will the fluid film last or just get washed off first time?
That’s what I want to know
Bought several cans of this stuff and applied it to my truck this morning. Let’s see how it works!
How did it work for you?
@@BaptistJoshua hey it worked awesome for me. I used about 4 cans on the underbody, and then one can for the doors and body panels. Totally worth it. I found once a year was enough. But then I moved to Arizona so undercoating is a thing of the past for me now 😎😎👊
@@QuintTheSharker Nice. Thank you. I am trying to figure out what non-oil resistant rubber they say not to use it on would be. Seems like vehicular rubber would be oil-resistant.
@@BaptistJoshua I get that. I was worried about it too. Depending on your vehicle, maybe you wouldn’t have to worry about it. My big thing was if the rust proofing degraded some rubber trim or seals over time, those parts are cheap to replace. But once the body starts to rust, the clock is ticking. For what it’s worth, I coated everything I could inside and out and I’ve never had any rubber fall apart on me and I started using fluid film 5 years ago.
@@QuintTheSharker Fluid Film responded to me by e-mail. They said:
*_Almost all rubbers are oil-resistant. The main areas we see and warn about are weather stripping on automotive doors. Bushings, boots, frame spacers and motor mounts are almost always oil-resistant due to their exposure._*
Love love love love FF. I use it underneath my mower decks and to lubricate almost anything. Spraying directly on batteries is ok? What about 7 pin trailer connectors? I've seen people use FF instead of Dialectic grease. I'm about to do my winter clean and seal on truck, dump trailer, and outdoor power equipment. Anyone have any bad experience using it with mowers, saws, or trimmers? Wondering if it could harm certain plants...
Can someone please tell me what is the correct name for the spray nozzle attachment that is being used in 2:36? Where it sprays 360.
Why do rubber parts of suspension and plastic parts like tire fender need to be coated?
This stuff is awesome. You really need the official FF application gun and 360 wand to do it right. One gallon has lasted me three years so far and that's with two apps a year in my SuperCrew F150. Just remember, a little goes a long way.
Derek Vinyard Thank you!
Derek Vinyard Do you have to have a compressor? I don’t have one
😁 My first application on my 2017 Super Duty crew cab 8' box. I used a hole gallon. Then 2 spray cans with small 360° tube for doors tailgate and hood. Mite be a little excessive but 2 years later looks perfect. The white Rancho shocks have 0 rust. They rust if you look at them wrong 😉. I apply twice a year.
It looks like there was some occasional overspray that might have gotten on the body. Is this hard to remove from the paint?
J_ White a degreaser with warm water will remove it
Can you spray it on any other engine parts? They only did the battery terminals.
Could someone tell me what to avoid while spraying?
Ghost- Face basically just the disk brakes and exhaust components. If there is any overspray on these areas it can be removed with a rag and a solvent like brake part cleaner.
Great product it seems but i have a question, mud and dirt usually sticks in my cars wheel wells. Does pressure washing after applying the fluid film remove it, what should i do?
Where can I buy these sprayers at in Canada ?
Amazon.ca, www.amazon.ca/Fluid-Ffprogun-Spray-Applicator-Extension/dp/B0070WTGZG/ref=sr_1_14?crid=VBUIXGJITED9&dchild=1&keywords=fluid+film+undercoating+kit&qid=1622255179&sprefix=fluid+film%2Caps%2C185&sr=8-14
Hi, Guys what's the correct name for the 360-degree wand and the red spray nozzle attachment being used at 2:35min?
============================================ or ===========================================
===================== The full equipment setup used.. I do have a compressor =======================
Hi Carlo, we offer a undercoating kit with the part number FFSG similar to the setup used with the nozzles here. This shop also used an airless(electric) paint sprayer which was a Graco magnum Pro LTS 170 but any airless system should work.
Does it come with liability insurance for when the tech sprays it on the brakes? @2:46
BPC was used to clean any overspray before the vehicle was off the rack.
I have a Graco spray gun. What size spray tip works with Fluid Film? Very good video, thanks
how does FF interact with Krown undercoating.....I'd like to apply FF over my Krown'd vehicle ?????
Fluid Film is designed to penetrate into the pores of the metal and can soften some existing coatings or be used to re-hydrate them if the salt/brine has dried it. Depending on the condition of the Krown coating you may just want to apply our film to the suspension components, inside rocker panels, doors, and other areas away from the Krown coating until it begins to crack and fail.
So this product won't attract dirt and look like crap when. It drips out of drain holes in doors,hoods,and trunk?
Fluid Film is a wet coating and can get a surface dusting of dirt. As the product is solvent free it does not get tacky like other wet coatings and the dirt often can be rinsed off without removing the coating.
Where do I get this done thoroughly Thank you!
how do they know how much they are putting in those holes. how can you trust that
Hello, the tips put out a good amount of product so it can creep and self level. The spray is consistent and can be seen at the opening of the access points to assess if another pass is needed.
I just had an authorized application shop do my new lifted Gladiator last week! Looks very shiny, and I actually like the smell haha.
What about if it gets on your shocks and car paint?
@@johnkim3658 hi John,
Fluid film is safe on suspension components including shocks. Our product also does not harm a finished paint with a clear coat if there is overspray. Simply wash off the overspray with a degreaser and water.
Can I still use it on the surface of a rocker panel, under the doors and door sills? Would it still stay or rub off there
Want to try it. What sprayers is he using? I like the fan tip type around the middle of the video that he used but don't know what it where to get it. Any help would be appreciated.
Ickes78 thank you for reaching out. the shop used a combination of an undercoating gun (shots with the wands) and a Wagner airless (electric powered) paint gun for the large chassis coating. Any airless paint gun should be sufficient for applying the product as we have used a number of different airless systems in the past. You can email us at info@fluid-Film.com if you want to ask about a specific gun.
Can you apply Fluid-Film over a dry layer of POR-15 and would washing the undercarriage with a power washer weekly over the winter cause the Fluid-Film to come off? Thanks !
Hi Alvin,
Thank you for your interest in FLUID FILM®. You can apply FLUID FILM® over POR-15 but it in not necessary to paint the surface because FLUID FILM® was designed to be applied over bare metal. We do not recommend pressure washing the undercarriage once FLUID FILM® is applied. FLUID FILM® is a wet coating and spraying it with a pressure washer will start to remove the product. If you want to clean the undercarriage you can use regular hose pressure. FLUID FILM® is not water soluble so any debris on top of the product will wash off and the product will stay behind. If you have any other questions please let us know.
Best Regards,
-FLUID FILM® Team
@@fluidfilmusa so can you go through car washes?
What pressure sprayer is that at 2:40?
The one used in the video is a Graco Magnum Pro LTS 170. Most standard electric paint sprayers can be used to suck the product directly from the cans, pails and drums.
Can I brush it on my truck frame? I don’t have a big enough compressor
In general what parts under the car can be coated and what do you want to stay away from ? Is it safe to spray bushings ?
Fluid Film is solvent free so it can be used on oil-resistant rubbers such as bushings, motor mounts, brake lines, and cv boots. The main areas to avoid are disc brakes (our product is a lubricant also) and the exhaust components (high temps will cause the product to smoke off).
If you accidentally coat the brakes some brake part cleaner and a rag will remove it. For the exhaust wiping the excess with a rag is fine. We also recommend avoiding the weather stripping inside doors as it is typically foam or an untreated rubber. As long as the product is wiped off in a few minutes it should not cause any issues.
What kind of service place does this, and what is the service called? Just "fluid film my chassis?"
We have an undercoater locator on our website www.fluid-film.com where you can locate shops. You can generally ask for a fluid film undercoating.
So, No need to eye pro or mask?
How many vehicles would the 5 gallon pale cover?
Full sized truck usually uses about a gallon. Sedans 1/2 gallon to 3/4 gal
How is this on a used car with rust on undercarriage?
This is a fantastic use for our product. As a wet coating it can be applied directly to a rusted surface (we recommend removing the loose scale if present) as it will soak into the rust and penetrate to the base. Effectively stopping the progression with minimal surface prep. We also have a black version of the film to both cover and treat the rust.
How long do you let the FF sit after application? Thanks.
As a wet coating. Fluid film is ready to go as soon as it is applied. If you’re going to be driving in wet conditions directly after an application you may want to wait 10-15 mins for it to fully settle before driving.
@@fluidfilmusa I really appreciate this. I have yet to find anything online about this. Thank you very much.
@@BailsOHay1 absolutely! You can always send questions to info@fluid-film.com or DM us on social media if you have any questions.
What is the brand of large coverage spray gun used? Not the one with the canister but the one fed directly by hose?
Been spraying this stuff for 7 years in Vermont, do about 40 cars a year, works AWESOME.
Thanks J.D. I believe it is a Wagner power sprayer with a feed tube directly into the 55 gallon drum.
Could you suggest appropriate sprayers or spec that works best with your product. Thanks !
We offer an undercoating kit through Napa Auto and O’reilleys with a part number FFSG.
Other than that most airless (electric) paint sprayers will work. Gracie and Lemmers both have a line of undercoating systems to handle our products.
I see he used the can with a long straw in one clip only. Where can I get the long straw
Just opened a 1 gallon jug that cost me $120 canadian. Its a paste? How am I supposed to spray it?
We have another video for mixing thick product. Fluid Film is thixotropic and can body up when in a container. We do this so once applied it resists wash off easier. Mixing the product well and getting not to a room temperature is usually best.
@@fluidfilmusa Thanks for the quick response, friend showed me that his can was also same texture. I was not aware I could apply it with a Shutz gun. I just spoon it into an empty undercoating container and all is working great.
When spraying with an Air Compressor,do you need to use a water filter (like when spray painting) when applying this product
William Green hello William, we have not had issues spraying without a moisture filter.
@@fluidfilmusa Thanks very much
What system is he using to spray the large parts of frame with no bottle attachment? I need that looks alot easier than the quart bottles
Our product has a similar viscosity to a house paint when we’ll mixed and can be applied directly with an airless (electric) paint sprayer directly from the gallon, 5 gallon, or 55 gallon drum. Any electric paint sprayer should work.
@@fluidfilmusa Yes...But can you please find out which setup are you using in this video? and let us know.
I dont recognize that gun with the wide fan tip and its working like a fire hose, not all airless paint guns will spray fluid film this well, ...Love the product..NEED THIS GUN SETUP!
***EDIT...gun appears to be a Graco magnum airless
@@Sk00terjolly Graco Magnum ProLTS 170 was what was used
@@fluidfilmusa Cool! that gun setup really gets coverage! Thank you!!
Hey, I love Fluid Film. Are there any issues with FF getting onto the brakes? I usually cover the drum/disc with newspaper to avoid overspray. I haven't seen anyone else do this though and notice in the video they get sprayed directly?
As our product is a lubricant we don’t recommend applying it to the brakes. In the case of overspray you can use brake part cleaner and a rag to remove the film. Most shops will bag or cover the brakes so they can coat the lines as close as possible.
Do you have to be careful with over spray, apart from the hot components mentioned in the video? Also, does this void any manufacturer warranties?
Should I hose of chassis before Applying this fluid film?
Hi Bob, as long as the chassis is relatively clean it should be good to go. Washing is only needed if there is caked on dirt or mud that prevents the film from soaking into the metal
anyone know what that long gun is called at 3:44?
@@torontoguy8043 that unit is a Graco Magnum Pro LTS 170. Graco has a number of guns and wands compatible with our products.
After applying Fluid Film is it wise to avoid the high pressure undercarriage carwashes?
Hi Andy,
Thank you for your interest in FLUID FILM®! Yes, we recommend not using high pressure undercarriage washes while FLUID FILM® is applied. If you want to rinse the chassis, simply use regular hose pressure. If you have any other questions please let us know!
Best Regards,
-FLUID FILM® Team
high pressure water is one of the worst things you can do to your car, with fluid film or not. Normal water hose is recommended.
@@fluidfilmusa why never dry
@@joshuarivera2478 Hard coatings typically trap rust and cover issues. it also doesnt allow the product to penetrate into pinch welds and seams like a wet coating which is where much of the protection is needed.
Can i apply this on already rusted undercarriage? Would it stop the further rust?
Yes! The advantage of the wet coating is that is soaks into existing rust and penetrates to the clean base metal preventing it from progressing. We do recommend removing loose scale first and if the rust is thicker you may need a second coat.
Should wheel well liners be removed to put down product?
Should be applied behind liners also. Some people remove them others use the wands to apply behind while it’s still attached.
What are undercoating type paints? Is it like the paint on a Toyota truck frame?
Had my friend detail my 1997 truck that has a perfect frame. He took the liberty of spraying 3 cans of CREST SUPER RUBBER COAT on my frame. How can I undo this??
Most rubber coatings are not oil resistant. Spraying FF and leaving it on the rubberized coating can soften it and make it easier to remove. Once removed you can apply Fluid Film.
I just treated my vehicle with this today. Does the smell inside the vehicle go away soon?
The smell should dissipate in 48 hours. Parking it outside for one night can help it air out after application.
So I dont need to wipe it down first or give it a car wash prior i can just spray it on rite away??
as long as it is relatively clean and dry it is good to go!
What's happens ? When u wash n details ur vehicle ? Does soap n other cleaners affect its longevity
Hi Brandon,
As a wet coating, Fluid Film does not need to be washed after a storm. High pressure sprayers and detergents can shorten the life of the product so we recommend against it. If you would like to rinse the vehicle with standard hose pressure that works but isn’t necessary. You can also still use drive through car washes without selecting the undercarriage spray.
@@fluidfilmusa of course I just mean the body not the undercarriage but appreciate the insight very much !
With all that spraying, you're bound to have a little overspray on your disc brakes. (I speak from experience) because my rear brakes squeak under load, is there a way to clean the stuff off? I've already tried brake cleaner.
95BerrySt break part cleaner works well for breaking it down.
Heavy braking burns it off, don't worry about it. Take a ride around the block and brake hard at the stops - ✔ solved.
Is this same gun and attachments still available?
Does this swell the rubber components? I was told not to use motor oil because it can swell the bushing in between parts
Fluid Film will not harm oil resistant rubbers. Almost all vehicles use an oil resistant rubber for their motor and frame mounts.
Can you apply direct to rusty surface?
@@DEADIKATED yes! When Fluid Film is applied directly to a rusted surface, it penetrates to the clean base metal and prevents the rust from progressing and softens the existing rust. We do recommend removing loose flaking rust before application to ensure the product can penetrate the the base. If the rust is extremely thick a second coat may be necessary.
@@fluidfilmusaawesome thanks my truck isn’t too bad mostly surface bc it’s always been in California
@@DEADIKATED perfect time to protect it and keep it that way! Thank you.
Is there a sprayer that would allow me to apply this with a smallish 4 CFM compressor?
Our undercoating gun typically needs 70-90 PSI to operate so most small pancake compressors will work.
@@fluidfilmusa Thanks! I just Fluid Filmed my car last week using the Husky 4.5 gallon "silent" compressor and a Wool Wax pro gun kit running at 85 psi. The compressor ran a lot but kept up! Pro gun is the best way to minimize time lying under the car. The spray cans were good for touching up spots I missed without having to drag the compressor out.
I use both Fluid Film and WoolWax. Spray Fluid Film on first to get maximum creep, preferably in summer. Then I come a month later and put WoolWax over the top. Won’t wash off.
Such an application warrants an under wash before hand and at least removal of all 5 wheels to access more areas.
Does any prep work need to be done ?
you should apply Preparation H
you guys mentioned to spray it on suspension components in the video. Is it safe? Cuz, some UCAs and coilovers have teflon coating. Can this be damaged due to Fluid film? Also can CV boots, Bushing and rubber from suspension components be safe?
mgltacoma Fluid Film will not harm oil-resistant rubbers like cv-boots, motor mounts and almost any other rubber underneath a vehicle.
As far as the Teflon goes, we have not done specific testing but know our product is used all over the off road racing for protection and lubrication of suspension components. Along with our daily commuters we have had no issues.
Teflon is the trade-name of PTFE. PTFE or Poly(TetraFluoroEthylene) is not able to be dissolved by any common solvents and is highly chemically resistant.
@@asdf8391 Thanks man. My Coilovers are rusty even with PTFE. So I am applying some Fluid Film to see if that helps.
Is fluid film safe on rocker panel plugs? They are rubber, I heard fluid film messes up rubber. I have a Tacoma that has rubber plugs at the bottom of the rocker panels.
Fluid Film doesn’t harm oil resistant rubbers. We have been applied inside rocker panels without issue for the last 20 years. The main area we have trouble is door seal gaskets. As long as the overspray is wiped off there should be no issue
@@fluidfilmusa thank you
What cleaning should be done before coating and how dry must the car be.
sponge bob Hi Bob,
A quick rinse is all that is needed. Fluid Film can be applied to a damp surface but the dryer the better. A leaf blower or air compressor can be used to dry the undercarriage quickly
Is there a difference between what your using in the video and the spray cans of fluid film, because I just got a couple cans and they spray out as a clear runny liquid, both the regular and the black
The only difference between the aerosol and bulk is the propellant in the can. They will preform equally.
*Also may be utilized on tires to enhance burnouts.
Where can I get the device the man is using? Bottle that has Fluid Film sticker with the extension wand.
Thanks for your interest in FLUID FILM®! One of our East Coast distributors makes and manufacturers that gun and bottle. Their company name is Kellsport Products and their website is: kellsportproducts.com
Hello, I recently took my truck to get this service at an authorized shop. Upon picking it up and inspection, the job had been done miserably. Anyhow, who can I reach out to? I'd like to share a video clip. Thanks.
Hi, thank you for reaching out and we are sorry to hear this. All of the shops are independent locations that use our products. We would still be happy to talk to you about it. You can reach out via info@fluid-film.com
Can I use fluid film on a motocycle engine and parts?
Nothing that gets over 220degrees but it can be applied to a number of areas such as forks, frame, chain, bolts, and areas where rust has started to form.
Love the stuff, just wish it was cheaper in the UK
What gun or type of gun is being used?
Do you have to sand existing rust?
Fluid film can be applied over an existing rust as it soaks into the rust and penetrates to the base clean metal. We do recommend removing any loose scale before application to ensure the product can be absorbed to the base.
how often does this need to be re-applied ?
Hello Bob,
Fluid Film is typically a once year application.
How often should you reapply to places like wheel wells and rockers as those get the highest wet areas due to kicking up rain, snow and salt?
Driving over 60 miles on the highway daily would more than likely wash the Fluid Film fairly quickly.
You might need to touch it up once or twice a winter for those high traffic areas. There is typically a good amount in the pores of the metal to last a full season but depending on conditions and usage touch ups are sometimes nescessary.
@@fluidfilmusa ok, thanks. 👍
should i mask off rubber boots and bushings?
Fluid Film does not damage oil-resistant runners so bushings, cv-boots and other components under the vehicle should be fine. Weather stripping on doors is typically the only rubber to look out for. If there is overspray you can wipe it off with a rag.
@@fluidfilmusa 👍
If you choose to use an airless sprayer to apply the FF product how do you clean the lines of your sprayer and pump? Also will FF effect any of the internals of the sprayer? I want to still use my airless sprayer to spray latex paint.
Nathan Hoover Hot water with a degreaser like dawn or simple green run through the lines will clear it. Then rinse with water through the line.
Thank you 😊
Does fluid film damage rubber bushings ? Sway bar bushings, lower control arm, sway bar end links, Strut dust boot? Etc? Does it cause expanding ?
Fluid Film does not harm oil-resistant rubbers. All of those components are typically oil resistant and are unharmed.
@@fluidfilmusa ok nice to know thanks for the reply ! 🤙🏻
Should you give your undercarriage a good wash before applying?
Cleaner is better. We mainly recommend washing so the product can reach the metal without being absorbed by mud. As a wet coating, even if there is a bit of salt residue our product doesn’t encapsulate it like a hard coating.
where do you get the spray equipment?
We sell a kit on Amazon, or available through NAPA Auto or Oreilleys. The part number is “FFSG” and requires a compressor. Fluid film can also be applied with an airless paint sprayer as it has a similar viscosity to a house paint when well mixed and at a room temperature.
DO YOU NOT NEED TO MASK THE VEHICLE? what if it gets on the paint? whats best to use for cleanup on painted surfaces and the gun afterwards? Looking to offer this service to my customers. I do paint work and detailing.
Fluid Film contains no solvents, silicone or Teflon so it is body shop safe. Our product does not harm a finished paint and can be removed by washing with warm water a pressure washer and a degreaser. Warm water and dish soap can be used to clean the gun if it will not be used for a longer period of time. If you would like more information about becoming an undercoater send us an email to sales@fluid-Film.com and we can further assist you.
WHERE DO I FIND A SHOP THAT DOES THIS
We have an undercoating locator on our website www.fluid-film.com/undercoating-locator/