I had this rattle in my 2005 Silverado (1500) for about 10 years now. Learned to live with it until one rainy day when I was bored and ready to pull the dash apart trying to find the source. Watched this video first, ordered the part (bearing) on EBay and just installed with your guidance. No more rattle and a $22 fix. Thank you Jeremy!
Thank you for taking the time to struggle through fixing the steering bearing. It was so helpful to all of us who have the same issue. But we have the advantage of watching you struggle and solve the mystery of removing and replacing this part. No apology necessary for camera movement!
Thanks man, this video really helped out. We did the same fix and this video helped us get it done in 45 min with basic tools. A shop wanted to charge $450 to get this done.
People like you make things easier for the rest of us. I have a 2002 Suburban 1500. Love this truck that has 194k miles on it. This has been bugging me for a while and I needed a good Saturday project. Ordered the $20 part and I'll be watching this video a couple more times I'm sure
Jeremy did mention it in his vid, but in the heat of battle we sometimes over look things. When you are on the last 3/8" to go on the install, make sure the notch on the steering column lines up with the heavier raised lines on the outside of the bearing. Thanks for the helpful vid.
Pretty sure this is the annoying rattle in my ‘10 2500HD. I prefer fixing minor things like this myself using the help of RUclips guys. Thanks so much for taking the time to make this video while fixing your truck w one hand! You rock
had the stupid clunk in my 2500hd '04 for too many years. watched the video and all in $22 and 30 mins work, solved. it was not as easy getting it back in as it was getting it out but well worth it. Thanks for the how to!
Very glad I could help man. I felt the same way, that dang clunk made the truck feel cheap and worn out. Nice to cruise down the road without wondering when the steering wheel's going to fall the bottom of the truck LOL. Glad it helped man.
I used a 35mm deep axle nut socket to use as a slight dead blow. It fits the inside of the bearing housing and around the steering shaft. Hope this helps, it worked for me!
Jeremy, thank you so much for your hard work and honest trial-n-error! I appreciate the information on getting the job more than camera skills. I look forward to getting my truck fixed. Thanks again
I ran into the same issues you did: ended up cutting 1" PVC pipe just a little longer than the shaft and then slid this over the shaft and used two thin boards to pry it into position. Could have saved an hour had I figured it out sooner in the process. Thanks for sharing you post.
Thank you. All the other "fixes" are BS. This worked perfect. Little hard getting it back in. I tried doing it without removing the accelerator pedal. Once I removed that I was able to get some persuasion on it and it went in. Thanks again for the video.
Loop your seat belt through the bottom of your steering wheel and then lock the belt into the anchor....push the seat back and your steering wheel isn't going to move while you work on these parts.
Nice to see things on a well made video. I had this issue way back when and the fix then was the ISS alone no mention of the bearing. Now time for the bearing and a new style ISS and this video will make that a lot easier, thanks....
After an hour of trying to put the Dorman piece in, I couldn't get it the last 3/4 inch. So I came up with a plan to use a deep socket (30mm) as a ram to press it on the rest of the way. I didn't need to use a hammer or anything else, just tap the part with the socket. If you do this, use a socket large enough that if is putting force on the outer rim of NEAR the bearing and not the bearing itself. Had it installed in a couple minutes.
Been trying to track down that sound for months , new upper control arms, tie rods, ball joints and bushings all around..still had the sound.. the Tahoe is all good now ..thanks
had the same issue and bought a new bearing, though the old one wasn't worn out it was only loose inside the column, so i just re-greased the old one and put some electrical tape on the outside of it. seems to be working fine and i've got a new one in case. Both were just as loose and the new one seemed a cheaper product.
To get the new part on, I used a short piece (about 3 to 4 inches) of schedule 40 1" PVC pipe to tap it in once you get it started on the shaft. Worked like a charm. Make sure the part is aligned properly for the last 1/4". Mine got stuck, and I rotated it 180° then it went in easy.
DUDE YOU ARE THE FUCKIN MAN. I was about to light this damn truck on fire I could not figure out for the life of me where the hell the rattle was coming from. You’re a life saver.
Did this job last weekend on my 04 Sierra 1500 4x4 Not sure why you had to take so much stuff apart; I only removed the gas pedal and disconnected the intermediate shaft at base of column from inside the truck. The intermediate shaft slides down to give enough clearance (barely) to get the old bearing assy out and the new one in. I didn't remove my lower dash trim or anything. I did, however, use my seat belt looped through the steering wheel as my truck no longer has working steering column lock (thank you, Albuquerque crackhead thieves for breaking it while attempting to steal the truck)
Anybody who's doing it right now here and 2024 You have to keep tapping on it with whatever you can tap on it with and it'll slowly go back up in there. He's right, they're right, it is a bear but it can be done. Lot of satisfaction when it's all done with and relief.
Replaced mine with the Dorman bearing and it lasted one week.. Started making a clicking - grinding sound, couple days after that the clunking started. After the fight to install it you can say I'm not real happy with Dorman right now.
Change your shaft also with the new GM part number 19329330, depending on how bad your shaft has failed, your bearing may last no time at all...the failure is a bad design of the steering shaft by GM, so your anger may be misdirected. Also there was a recall on that shaft...but the new GM after the bankruptcy probably wont honor it.
Be sure that the old bearing race cap come off the shaft before installing the new one. Mine didn’t and the new part would seat. Broke the new one while trying to get it back out. Then had to fish both bearing race caps out of the inner shaft.
Very Informative step by step video and explanation! Thank you for the efforts! Going to perform that to my '02 Tahoe ;) Internet suggests to secure the steering wheel in place using its lock feature or fastening with the seatbelts..will look into this.
I know this is an older post but these can be a nightmare to get off and on. Do yourself a favor and remove the gas pedal to get more room to work and if it doesn't slide off that last several inches be prepared to lose a lot of sanity trying to get it out. Didn't have to much of an issue getting the new one back in place but the steering shaft has to be perfectly aligned use a pry bar then wiggle the steering wheel and it will help get in place. Even the 15mm bolt holding it in place was a mother to get out, it took an impact to get it off guessing had some pretty aggressive thread locker on it.
I'm sure by now after 6 years you have that fixed. But the reason it was making noise and rattling is because the old one was it long agated and the hole was certainly bigger than the new one. I've done a few of them I have a fleet of '07 Chevys and they all end up rattling.
I did this yesterday to an 07 and it is a pain to get installed. I used a 1-1/8" deep socket along with a pry bar to install after I got it started by hand.
Wow Jeremy , thaaanks , i did not know it was that easy ! i have a 2003 Silverado and the steering does a clunk just Like that too , its kind of annoying , what brand company of bearing did you use ? thanks again !
How did that trick work for ya...explain it if you don't mind...ive bought the bearing and upper shaft but haven't tackled it yet....may return the parts if there's a trick to be able hold off on spending that 119 bucks
After you installed the bearing did you ever try to wiggle the steering shaft itself, not the one that stick out into the engine bay, but the one that's literlly connected to the steering wheel. I did this on my truck recently and noticed that even though the bearing was a tight fit and does not move at all, the shaft/pole connected to the steering wheel does still, it bothers me and I'm not sure if that ho it's supposed to be, for I don't remember it doing that with the recent GM bearing.
I've done this twice. My 1500 got this. Fixed everything else. Someone steals it off driveway at my house in great neighborhood. Gone never saw again. My GMC 2500 had this too. Fixed! QUESTION: I saw in your video you put some headers on! What brand/no headaches install/cost are these? I'm interested in some shorts for my truck. Thanks.
Thanks for this, I already replaced the shaft and it helped partially but over broken pavement or cobblestone it rattles like a bastard. Have the bearing in hand, just needed a guide since I read it was a bitch to swap.
Might not want to do it like this...... It's way easier to just remove the steering column and then change the bushing - watch this video: ruclips.net/video/fmSss-shcKY/видео.html .... Yes, it can be done without removing the steering column but it is VERY difficult working in a super tight space as shown here. For my 2003 suburban all I had to do was 5 things: 1) remove dash trim and HVAC duct to get out of way, 2) remove shield under column (4 nuts), 3) unplug connections, 4) unbolt from shaft, 5) unbolt from firewall frame (4 nuts). With proper extensions all nuts super easy to get to except the shaft which is not too bad. Once column out super easy to change out bushing. REMEMBER - since you are putting it back in, before you remove shaft-bolt duct tape the steering wheel to the column and don't hold it by the steering wheel while your removing so that you don't spin it while out - spinning can damage the spring inside... here the link again ruclips.net/video/fmSss-shcKY/видео.html
These things are a real pain. I replaced mine with a Dorman bearing last year and it has already failed. I'm curious if your new bearing is holding up, or did I get a defective part??
I have the same problem with my 2004 gmc sierra 2500hd clunking sound when going over speed bumps. My mechanic told me that I need a new steering column, not sure it's just the bearing or the compete steering column.
Unrelated but I noticed your longtubes installed in this video. Would you be able to post a pic or video of the way you connected them to your factory exhaust tubing?
What is the part # on that? I found two on auto store places online. One is lighter green and one is a darker green. I don’t know what the difference is. I just bought a used 2004 chevy 1500 with 108,000 miles and it will pop every once in a while when I turn. Please and thanks.
Helped slightly with the loose steering, and dramatically with the clunk noise. I think my gearbox needs tightened up a bit, might take some slack out of the steering.
The way you describe the noise is dead on. It sounds like my truck is falling apart. I thought maybe it was a ball joint but they're tight and greased. So I narrowed it down to something in the dash behind the steering wheel. The steering is tight inside the cab. But when I go into the engine bay and wiggle that shaft it has play and makes that god awful noise.
GM should make these parts out of metal so they last a lifetime,but then they wouldn’t make any money would they,major design flaw in my view.oh well guess that’s the way the cookie 🍪 crumbles.
I have a 2007 chevy silverado extended cab that vibrates when I break and at very low speeds. I replaced the outer tie rod that was lose and replaced the stabilizer link. I also replaced all rotors and drums and all breaks but problem is still there. truck vibrates at very low speeds when I break at low speeds but not when i break hard. Any advice would be appreciated thanks.
Happy to hear it man. Give's the vehicle a "new" kind of feeling when it rolls down the road without sounding like it's going to fall apart. Crazy how much noise the original bearing makes.
My apologies for the late reply, if you get under your dash and grab the steering column shaft, if you can wiggle it, THAT wiggle means the bearing I replaced in this video is worn out. If you turn your steering feeling and hear a muffled clunking noise, that means the other half of the shaft is worn out and needs replaced.
I had this rattle in my 2005 Silverado (1500) for about 10 years now. Learned to live with it until one rainy day when I was bored and ready to pull the dash apart trying to find the source. Watched this video first, ordered the part (bearing) on EBay and just installed with your guidance. No more rattle and a $22 fix. Thank you Jeremy!
Steve, glad to hear I was able to help and that you tackled the job with success. Cheers mate.
How long does this fix seam to last?
Thank you for taking the time to struggle through fixing the steering bearing. It was so helpful to all of us who have the same issue. But we have the advantage of watching you struggle and solve the mystery of removing and replacing this part. No apology necessary for camera movement!
Thanks man, this video really helped out. We did the same fix and this video helped us get it done in 45 min with basic tools. A shop wanted to charge $450 to get this done.
People like you make things easier for the rest of us. I have a 2002 Suburban 1500. Love this truck that has 194k miles on it. This has been bugging me for a while and I needed a good Saturday project. Ordered the $20 part and I'll be watching this video a couple more times I'm sure
Thanks man, I appreciate the compliment!
Jeremy did mention it in his vid, but in the heat of battle we sometimes over look things. When you are on the last 3/8" to go on the install, make sure the notch on the steering column lines up with the heavier raised lines on the outside of the bearing. Thanks for the helpful vid.
Pretty sure this is the annoying rattle in my ‘10 2500HD. I prefer fixing minor things like this myself using the help of RUclips guys. Thanks so much for taking the time to make this video while fixing your truck w one hand! You rock
had the stupid clunk in my 2500hd '04 for too many years. watched the video and all in $22 and 30 mins work, solved.
it was not as easy getting it back in as it was getting it out but well worth it. Thanks for the how to!
Very glad I could help man. I felt the same way, that dang clunk made the truck feel cheap and worn out. Nice to cruise down the road without wondering when the steering wheel's going to fall the bottom of the truck LOL. Glad it helped man.
I used a 35mm deep axle nut socket to use as a slight dead blow. It fits the inside of the bearing housing and around the steering shaft. Hope this helps, it worked for me!
I will keep that in mind in case this ever comes up again. Thanks for the suggestion brother.
Jeremy, thank you so much for your hard work and honest trial-n-error! I appreciate the information on getting the job more than camera skills. I look forward to getting my truck fixed. Thanks again
I ran into the same issues you did: ended up cutting 1" PVC pipe just a little longer than the shaft and then slid this over the shaft and used two thin boards to pry it into position. Could have saved an hour had I figured it out sooner in the process. Thanks for sharing you post.
Thank you. All the other "fixes" are BS. This worked perfect. Little hard getting it back in. I tried doing it without removing the accelerator pedal. Once I removed that I was able to get some persuasion on it and it went in. Thanks again for the video.
Your video helped me. I was afraid you was going to get aggravated and stop videoing but you hung in there. Thanks!
softail2k3 Thank you! Glad to hear it was useful to someone.
Awesome video, best one out there by far. Just did this in my driveway, 35 minutes including tool cleanup. Thanks man!
Loop your seat belt through the bottom of your steering wheel and then lock the belt into the anchor....push the seat back and your steering wheel isn't going to move while you work on these parts.
Nice to see things on a well made video. I had this issue way back when and the fix then was the ISS alone no mention of the bearing. Now time for the bearing and a new style ISS and this video will make that a lot easier, thanks....
After an hour of trying to put the Dorman piece in, I couldn't get it the last 3/4 inch. So I came up with a plan to use a deep socket (30mm) as a ram to press it on the rest of the way. I didn't need to use a hammer or anything else, just tap the part with the socket. If you do this, use a socket large enough that if is putting force on the outer rim of NEAR the bearing and not the bearing itself. Had it installed in a couple minutes.
Been trying to track down that sound for months , new upper control arms, tie rods, ball joints and bushings all around..still had the sound.. the Tahoe is all good now ..thanks
Thank you Jeremy. I have put up with this for years but am going to fix it now. You rock Dude. Good comments also.
Just changed mine today, man your wrench levering idea was genius and a life saver!
Thanks for showing and sharing what is involved with that hearing replacement. Big help!
So worth doing this bearing, Just did mine and feels like a new truck in the steering and no more noise.
had the same issue and bought a new bearing, though the old one wasn't worn out it was only loose inside the column, so i just re-greased the old one and put some electrical tape on the outside of it. seems to be working fine and i've got a new one in case. Both were just as loose and the new one seemed a cheaper product.
To get the new part on, I used a short piece (about 3 to 4 inches) of schedule 40 1" PVC pipe to tap it in once you get it started on the shaft. Worked like a charm. Make sure the part is aligned properly for the last 1/4". Mine got stuck, and I rotated it 180° then it went in easy.
Thanks for making this video. I will be replacing one of these bearings in a few days and now thanks to you I know how to do it.
DUDE YOU ARE THE FUCKIN MAN. I was about to light this damn truck on fire I could not figure out for the life of me where the hell the rattle was coming from. You’re a life saver.
You saved my life with that wrench trick thanks much great job great video
Did this job last weekend on my 04 Sierra 1500 4x4
Not sure why you had to take so much stuff apart; I only removed the gas pedal and disconnected the intermediate shaft at base of column from inside the truck. The intermediate shaft slides down to give enough clearance (barely) to get the old bearing assy out and the new one in. I didn't remove my lower dash trim or anything. I did, however, use my seat belt looped through the steering wheel as my truck no longer has working steering column lock (thank you, Albuquerque crackhead thieves for breaking it while attempting to steal the truck)
This is great, thank you very much for going to the trouble of making this video. I was able to fix my rattle!
Anybody who's doing it right now here and 2024 You have to keep tapping on it with whatever you can tap on it with and it'll slowly go back up in there. He's right, they're right, it is a bear but it can be done. Lot of satisfaction when it's all done with and relief.
Getting ready to do this job, found your video and how lucky I was. Thank you for making it.
Replaced mine with the Dorman bearing and it lasted one week.. Started making a clicking - grinding sound, couple days after that the clunking started. After the fight to install it you can say I'm not real happy with Dorman right now.
Change your shaft also with the new GM part number 19329330, depending on how bad your shaft has failed, your bearing may last no time at all...the failure is a bad design of the steering shaft by GM, so your anger may be misdirected. Also there was a recall on that shaft...but the new GM after the bankruptcy probably wont honor it.
Excellent filming of the problem.
Really good information thank you I have a 2005 that noise drives me nuts going to be fixing on that soon
Be sure that the old bearing race cap come off the shaft before installing the new one. Mine didn’t and the new part would seat. Broke the new one while trying to get it back out. Then had to fish both bearing race caps out of the inner shaft.
THANKS!!!!
Saving me a lot of money during COVID.
Stay safe!!
Very Informative step by step video and explanation! Thank you for the efforts! Going to perform that to my '02 Tahoe ;) Internet suggests to secure the steering wheel in place using its lock feature or fastening with the seatbelts..will look into this.
I know this is an older post but these can be a nightmare to get off and on. Do yourself a favor and remove the gas pedal to get more room to work and if it doesn't slide off that last several inches be prepared to lose a lot of sanity trying to get it out. Didn't have to much of an issue getting the new one back in place but the steering shaft has to be perfectly aligned use a pry bar then wiggle the steering wheel and it will help get in place. Even the 15mm bolt holding it in place was a mother to get out, it took an impact to get it off guessing had some pretty aggressive thread locker on it.
I'm sure by now after 6 years you have that fixed. But the reason it was making noise and rattling is because the old one was it long agated and the hole was certainly bigger than the new one. I've done a few of them I have a fleet of '07 Chevys and they all end up rattling.
Thanks for the vid. It help me out as well. However, I did notice that you did not install the sensor that goes over the bearings housing
Thank you so much for taking the time and making this video it was a great help to me
Great Video DUDE , very well done !!!
Thanks man!
You answered/FIXED my issue......THANK YOU.....TO search for the part....whats the name to ask the dealer???
Spit on it!! Lol always works. All the gm's ive had had same issue. I just lived with it. But now its time to change mine.
so annoying. Lol
Good info was gonna replace upper and lower shafts to try to get rid of sound thanks Bud ,(same heat here in bc canada just add mosquitos )
Thanks for the tip. 30 minutes to install.
If you heat the new bearing under a light bulb it expands and is easier to get on.
Jesus, I needed to take Dramamine. Your camera work is brutal.
Sorry dude. It was with my iPhone.
Haha I hate doing this, I've had to do it twice and going on a third time here shortly. Major pain in the butt to He-Man the new bearing back in.
I did this yesterday to an 07 and it is a pain to get installed. I used a 1-1/8" deep socket along with a pry bar to install after I got it started by hand.
You're a good man, thanks Jeremy !
Thank you Courtney
Wow Jeremy , thaaanks , i did not know it was that easy ! i have a 2003 Silverado and the steering does a clunk just Like that too , its kind of annoying , what brand company of bearing did you use ? thanks again !
The clock spring will be fine if the str wheel moves, just don't attach everything if it went a full 360 either way.
This was a great help.
I had little faith in the wrench idea but it worked! Pita
Gonna work on mines today.. wish me luck.
best video out there
"Pretty demoralizing". Perfectly stated!
Thanks for sharing this video 👍👍
put the seat belt hold it in place then back up seat
So basically, the bearing is the only part i need then? I've got that annoying clunk as well and thought it might be the steering shaft also
Think I'll try the 2 inch hose clamp around the bearing trick first
How did that trick work for ya...explain it if you don't mind...ive bought the bearing and upper shaft but haven't tackled it yet....may return the parts if there's a trick to be able hold off on spending that 119 bucks
Great video going to do mine now thank u ..... 👍
Have fun!
After you installed the bearing did you ever try to wiggle the steering shaft itself, not the one that stick out into the engine bay, but the one that's literlly connected to the steering wheel. I did this on my truck recently and noticed that even though the bearing was a tight fit and does not move at all, the shaft/pole connected to the steering wheel does still, it bothers me and I'm not sure if that ho it's supposed to be, for I don't remember it doing that with the recent GM bearing.
I've done this twice. My 1500 got this. Fixed everything else. Someone steals it off driveway at my house in great neighborhood. Gone never saw again. My GMC 2500 had this too. Fixed! QUESTION: I saw in your video you put some headers on! What brand/no headaches install/cost are these? I'm interested in some shorts for my truck. Thanks.
Thanks for this, I already replaced the shaft and it helped partially but over broken pavement or cobblestone it rattles like a bastard. Have the bearing in hand, just needed a guide since I read it was a bitch to swap.
Might not want to do it like this...... It's way easier to just remove the steering column and then change the bushing - watch this video: ruclips.net/video/fmSss-shcKY/видео.html .... Yes, it can be done without removing the steering column but it is VERY difficult working in a super tight space as shown here. For my 2003 suburban all I had to do was 5 things: 1) remove dash trim and HVAC duct to get out of way, 2) remove shield under column (4 nuts), 3) unplug connections, 4) unbolt from shaft, 5) unbolt from firewall frame (4 nuts). With proper extensions all nuts super easy to get to except the shaft which is not too bad. Once column out super easy to change out bushing. REMEMBER - since you are putting it back in, before you remove shaft-bolt duct tape the steering wheel to the column and don't hold it by the steering wheel while your removing so that you don't spin it while out - spinning can damage the spring inside... here the link again ruclips.net/video/fmSss-shcKY/видео.html
These things are a real pain. I replaced mine with a Dorman bearing last year and it has already failed. I'm curious if your new bearing is holding up, or did I get a defective part??
It started to make noises after about a year unfortunately :/ Not as bad as before, but still crappy I'm going to have todo this again.
Part number for bearing? Thanks for video. Will tackle this job in a few weeks.
I just bought the Dorman bearing yesterday...ill post the part number for you in the morning
Nice truck
Get you a Rock Form phone case with built in magnets for help holding phone while working and making videos
Great video!!!
thanks so much....i will try this. 👍🏻
Good job buddy 👌🏻👌🏻
Your were an animal for doing it with one hand but I appreciate the video
I have the same problem with my 2004 gmc sierra 2500hd clunking sound when going over speed bumps. My mechanic told me that I need a new steering column, not sure it's just the bearing or the compete steering column.
Thanks
Unrelated but I noticed your longtubes installed in this video. Would you be able to post a pic or video of the way you connected them to your factory exhaust tubing?
No worries man! Just uploaded a video specifically covering this. Should be finished processing here in just a few minutes.
What is the part # on that? I found two on auto store places online. One is lighter green and one is a darker green. I don’t know what the difference is. I just bought a used 2004 chevy 1500 with 108,000 miles and it will pop every once in a while when I turn. Please and thanks.
Does this make noise just rolling down the road like a rhythmic ticking
Did it seem to help the loose steering or just the clunk noise? Thanks for the help, I feel the same way. Makes it feel like a buggy.
Helped slightly with the loose steering, and dramatically with the clunk noise. I think my gearbox needs tightened up a bit, might take some slack out of the steering.
If you would of put the nut and bolt back on the steering wheel you could of had some leverage
The way you describe the noise is dead on. It sounds like my truck is falling apart. I thought maybe it was a ball joint but they're tight and greased. So I narrowed it down to something in the dash behind the steering wheel. The steering is tight inside the cab. But when I go into the engine bay and wiggle that shaft it has play and makes that god awful noise.
I think with me its the shaft u joint thats loose. I'll replace the bearing too but now I have to figure out how that comes out
Should be titled, let us learn together
GM should make these parts out of metal so they last a lifetime,but then they wouldn’t make any money would they,major design flaw in my view.oh well guess that’s the way the cookie 🍪 crumbles.
great job
Thanks Emilio
what part of az u live in need help with that
59th Ave & Thunderbird - Glendale, AZ. Hit up Dylan Klaas with CavalryAutomotive - www.cavalryautomotive.com
Not sure if it's just the bearing or the compete steering column.
I have a 2007 chevy silverado extended cab that vibrates when I break
and at very low speeds. I replaced the outer tie rod that was lose and
replaced the stabilizer link. I also replaced all rotors and drums and
all breaks but problem is still there. truck vibrates at very low speeds
when I break at low speeds but not when i break hard. Any advice would
be appreciated thanks.
It’s your exhaust o ring! It took me forever to find that out on my truck
I have same pro ken with my ls430..Where can i get the part online? Thx
www.amazon.com/gp/product/B004AI9SQA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Could this be the same for a Chevy avalanche to? Mine rattles all day 🤣
nice gauge cluster
Thanks man!
Is it a normal thing for you to work on your car barefoot?
Could I buy this at autozone?
I REPLACED ALL THESE DID NOT FIX PROBLEM,SAME RATTLE,,,????
So what was the time frame on doing this??? Looks easy.
I'd say if I went back to do this, it would take me half an hour to install from start to finish.
My 2005 1500 has same issue. Not anymore.
Happy to hear it man. Give's the vehicle a "new" kind of feeling when it rolls down the road without sounding like it's going to fall apart. Crazy how much noise the original bearing makes.
Was the shaft a new part also or just the bearing
Just the plastic bearing.
Lol sounds like me fixing shit on my truck
Haha hell yeah broski
So lets get this straight how am i sure if its the shaft to replace or the bearing or should i do both
Bczz every search i did the shaft needs lubrication or replacment
My apologies for the late reply, if you get under your dash and grab the steering column shaft, if you can wiggle it, THAT wiggle means the bearing I replaced in this video is worn out.
If you turn your steering feeling and hear a muffled clunking noise, that means the other half of the shaft is worn out and needs replaced.
What kind of headers are they can you still get to your plugs easily
Absolutely. They're Pacesetter headers. Fit great, look great, no issues with them.