what I like about Honda motorcycles is they all have the same procedure of dismantling and rebuilding, I got Honda xl200 (Brazil models) and the process is basically the same. kudos great video series
Nice job! Hey just a little tip ,when you replace that exhaust gasket turn those half moon collars around the other way and wrap a piece of masking tape around them to hold them in place. The tape will burn off the first fire up.👍
Nice work! Yeah, you need that copper seal hehe.. But she runs smooth! Exciting to see how she perform on the trails, considering she is a 200. Thanks for the upload!
Thanks Erik! I’ve gotten lucky before and reusing that crush gasket…this time not so much lol. If that’s all that’s wrong with it though, I’ll take it lol.
Disconnect the de compressor cable when you use the compression tester, as soon as you kick it, the exhaust valve is opened so you lose compression, I used to have a XL185, which used the same basic motor.
Sounds brilliant , top job with the top end rebuild , just the exhaust leaking a bit I think new copper seal and collars seated a bit better 😁 be good to see it on the move . And that carb seems like the buy of the year. 👍👍 Great job .
Thank you! I actually had the header collar on backwards lol. Luckily Andy from Andy’s XL Restoration channel caught it and gave me the heads up! I’m still baffled by how well the carb works too.
Wow, bike started up perfectly. Nice work. I'm having trouble with the XR200R OEM carb. Can't seem to get the idle right and I've cleaned it several times now. Can you share a link to where you bought the ebay carb? Thanks.
Thanks Martin! Here’s the link off Amazon: tianfeng Carburetor For Honda XR200 XR200R 1980-2002 Carb W/ Air Filter a.co/d/9KwH3ti Have you tried blowing out the idle air circuit real good? I had another bike I was working on give me the same trouble even after an ultrasonic bath until I blew compressed air into the air screw hole and the couple small holes that are facing the intake side of the carb. Cured that instantly.
@@Garage2Trail I didn't have any luck with another cleaning cycle and blowing compressed air through all the holes. Carbs are frustrating! I bought the same Amazon carb you did and was wondering how many turns out the fuel/air screw and the idle screw were turned out? Thanks!
@@martintelford8763 ahh bummer. To be honest I don’t know. I just threw it on the bike and it started easy and idled. I only had to mess with the idle by turning it up just a hair after it warmed up.
what I like about Honda motorcycles is they all have the same procedure of dismantling and rebuilding, I got Honda xl200 (Brazil models) and the process is basically the same. kudos great video series
Thank you! I appreciate knowing people are liking my stuff!
One of the coolest small bikes they ever made was the XR 75. very sweet like the XR 600
I love them all. The Z50 has a spot with me too.
Nice job! Hey just a little tip ,when you replace that exhaust gasket turn those half moon collars around the other way and wrap a piece of masking tape around them to hold them in place. The tape will burn off the first fire up.👍
Thank you Rich! That’s a really good idea with the tape. I’ll make sure I do that when the gasket arrives.
That sounds like it’s running great and doesn’t seem to smoke a bit! Look forward to the running video :)
I can’t wait to ride it on the trails I used to ride the ‘87 XR200 I had from ‘96-‘99. Should a fun video.
Bike reminds me of my '74 XL175 Honda. Pretty bullit proof engine, but not the most powerful. Perfect little bike for gravel roads.
I have one of those too! Great little bikes. The XL175 from 73 and 74 are some of the best looking bikes in my opinion. Love the Mars Orange!
Nice work! Yeah, you need that copper seal hehe.. But she runs smooth!
Exciting to see how she perform on the trails, considering she is a 200.
Thanks for the upload!
Thanks Erik! I’ve gotten lucky before and reusing that crush gasket…this time not so much lol. If that’s all that’s wrong with it though, I’ll take it lol.
@Garage2Trail I kinda like bikes that have that wear and tear, but are in a good mechanical condition. She looks to be just that 😊👍
Runnin clean!
Disconnect the de compressor cable when you use the compression tester, as soon as you kick it, the exhaust valve is opened so you lose compression, I used to have a XL185, which used the same basic motor.
Thank you! I’ll have to give it a try…didn’t even consider the auto decompression.
@@Garage2Trail Cracking bikes, I wish we had them here in the UK.
Sounds brilliant , top job with the top end rebuild , just the exhaust leaking a bit I think new copper seal and collars seated a bit better 😁 be good to see it on the move . And that carb seems like the buy of the year. 👍👍 Great job .
Thank you! I actually had the header collar on backwards lol. Luckily Andy from Andy’s XL Restoration channel caught it and gave me the heads up! I’m still baffled by how well the carb works too.
Very cool, congrats 👍
Thank you!
Awesome channel my dude. Deserve a metric shit tonne more subscribers than you have. May the youtube algorithm look kindly upon you. 🤘
Thanks man, I really appreciate that!
Exhaust collets are in the wrong way round m8 nice job
Good eye Andy, thank you so much!
exactly!!
Wow, bike started up perfectly. Nice work. I'm having trouble with the XR200R OEM carb. Can't seem to get the idle right and I've cleaned it several times now. Can you share a link to where you bought the ebay carb? Thanks.
Thanks Martin! Here’s the link off Amazon:
tianfeng Carburetor For Honda XR200 XR200R 1980-2002 Carb W/ Air Filter a.co/d/9KwH3ti
Have you tried blowing out the idle air circuit real good? I had another bike I was working on give me the same trouble even after an ultrasonic bath until I blew compressed air into the air screw hole and the couple small holes that are facing the intake side of the carb. Cured that instantly.
@@Garage2Trail I haven't tried compressed air yet, just the ultrasonic cleaner. I'll give that a try before I try a new carb, thanks for the tip.
@@martintelford8763 hope that works for you!
@@Garage2Trail I didn't have any luck with another cleaning cycle and blowing compressed air through all the holes. Carbs are frustrating! I bought the same Amazon carb you did and was wondering how many turns out the fuel/air screw and the idle screw were turned out? Thanks!
@@martintelford8763 ahh bummer. To be honest I don’t know. I just threw it on the bike and it started easy and idled. I only had to mess with the idle by turning it up just a hair after it warmed up.
looks like you have your exhaust shims in backwards
Yup I did lol…got it figured out afterwards 😆
Thanks 😊
Nice man! Could you share a link for the carb?
Thanks! Here you go: www.amazon.com/dp/B081MWTQ1W?ref_=cm_sw_r_apin_dp_EPBYGNH1KY595ZGEEYF2