Even though this video is 2 yrs old it still just as relevant today. I just got this charger and even though I read through all the directions this video was a big help to understand it all. Thank You!
Being a noob in the rc jet scene can be frustrating trying to learn the ropes. Your vid was the exact opposite, quick and to the point and easy to understand, thanks!
Good demo. I need this kind of video as i just buy a imax b6 charger. Thanks.. very easy to understand. No gimicks. just a straightforward demo. I subd as well
Very informative, Thanks for the guide on the charger. The time lapse of the charge was pretty cool. I noticed you did a quick retake of what you said at around 6:40. Just lettin' you know. Also, on rare occasion, particular chargers don't interact well with particular batteries, which is something else to take into consideration when getting a charger. It's pretty uncommon, but it's much better to catch it early rather than later.
@@jbmods692 I put the battery to charge normally with the process you showed in the video and after 10 seconds it stops charging and throws me out and doesn't charge. I don't understand why this happens?😓
Hey mate, very good question. If they battery isn't a reputable brand, I would just charge it at a max current of around 0.5amps just to be on the safer side. Then we you have done a test and know the actual capacity you can up the current.
One thing I really don't like about this charger is: you can't charge a half-discharged NiMH battery, for example, without fully discharging it first. Whatever battery you're charging, you have to fully discharge it first. If I'm missing something about the operation of this device, please respond.
I just got the imax but what I'm trying to find is how to discharge an ebike battery The cable you're using on the negative positive side is the same connection can you make a video
Hi. Please can you help me out. I have a Li-ion battery 7.4V and 1500mAh. Firstly, do I select Lipo for charging? My Imax charger does not have a selection for Li-ion. I have followed your first example in your video, however, when I select Starr charging, a message appears as follows: R: 1SER S:2SER. When I select start, an error message appears Li2S Full. This is a brand new charger that I have bought and struggling. Thanks, Sean
Hi so iv got this changer and iv got a 14.8v 4s 6000mah 70c battery so what amp should I set please can't find info anywhere really appreciate if you can help
These chargers can only throughput about 60watts. So you could only charge your 6000mah 4s battery at about 4amps - NOT the 6Amps of a normal 1C charging rate. So it will just take longer.
Hi, nice video. can you please tell us how to calibrate this charger and what is that system update when i hold ENTER and then on the charger. This system update takes so much time.
i have the fake model, but reviews seem decent, anyways i want to know if i want to balance charge my power bank, do i need to desolder the cells from parallel, then set up in series? they are in parallel, 3.7v per cell.
I have a Life battery cell that is marked as 3.2V. This charger has the Life cell settings as 3.3V. Is there a way to change that in the charger to 3.2v?
I have one like this and everything works except, charge in balance mode and balance battery . Work couple seconds and then on the screen at mah shows 0 and stay like this hours . In simple mode charge in series reach's at the end, but in balance mode charge or balance battery do nothing . You tasted yours it's ok ? Thanks
I know this video is a few years old now but just a couple questions. First off, how do you know when it's charged? I ran the battery basically dead. Car was at walking speed. Put it on the charger and the 7.4v 2s lipo was already reading around 8.4v 🤷♂️. The charger seemed to still be putting power in to it. I took it off after 30 mins. Nothing seemed to have changed much numbers wise. Also I noticed in the video you started off with a 1500mah battery and you set the capacity cut off to 1500mah. Later in the video you charged a 3300mah battery and changed the charge amps to 3.3 but didn't change the capacity cutoff from 1500. Will this be a problem. I think I did the same thing switching from my 1800mah heli battery to my kids 3300mah car battery
The charger beeps and says battery is full once done. Unless you're fast charging, it's going to take longer than 30mins to charge most batteries. The 1c charge rate is to maintain battery longevity. The higher input voltage (8.4v) will be higher than the nominal voltage (7.4v) of the battery, that's normal.
i dont have the cord for the output... i am trying to charge an 11.1v elite soldier battery for a gel blaster. Do I need both plus in or is the the pin white plug enough?
The charger will stop charging when the battery is full. I only put mine to storage if I am not using the batter in the next day or 2. Storage is to keep the battery at its most stable storage voltage to prolong the life of the battery and is safer than storing the battery at 100% charge.
Hi, can you type the name of the cable you are using for charging? Thanks Is ths laso possible with this model to monitor the level of the charge through the App of the cellphone? Bye
I'm pretty sure it depends on your charge rate.. If you charge at 5.2 amps it will take 1 hour.. If you charge at 2.6 amps it will take 2 hours. Does that seem right to anyone else?
@@bmzaron713 That is correct, generally you charge your batterys at 1c which is 1 x the amp hours of the battery. So a 5200mah would be 5.2amps and take 1 hour to charge.
Hey, As long as the battery chemistry is one that the charger supports it shouldn't matter on the size of the battery. It will just take a while to charge with that big of a battery since the charger is limited to 6amps I believe. Does that all make sense?
At 8:21 in your video, it shows 5 zeros in the lower right corner -- these numbers increase over time for Pb charging -- what are they for? Not in any documentation I can find
Hey mate, those numbers are displaying how much energy has gone in or out (depending on if you are charging or discharging) in milliamp hours. Useful for seeing the actual capacity of a battery.
WHEN I CHECK MY BATTERY IT SAYS 4S.... WHEN I HAVE A 6S ..... BATTERY 5200 mAH 50C 22.2 volt but i cant find out how too change the settings to 6s ???? HOW DO I DO THAT ?
Hi man I watched your video but it didn"t answer my probmems :/ I bought the Imax B6 (for some reason it's black and not blue And I am facing multiple problems: When I try to "BALANCE CHARGE", it auto-detect as 2S and even when it's blinking I can't change the value to 3S-4S-5S-6S The chager never match the cell number of my battery no matter which mode I'm in : I plug my 6S battery in and it detects 2S On other charging modes; I can force the 6S but then, before I start the charge, it says " R = 4SER S= 6SER " If I force the charge like so ( R = 4SER S= 6SER) the Battery voltage actually goes down as time goes by Do you have any idea of a fix ? Or did i receive a faulty chager ?
Hey mate, As long as the charger has the right profile for the battery type and correct connection there should be no need to mod the charger. What battery are you planning on charging?
Hi, you can not use this to charge a car battery. You need to buy a specific charger depending on the chemistry of your car battery that is designed for it. The Imax B6 has a maximum output of 50w.
@@jbmods692 but there is a option to charge lead acid battery as a Pb, i think it is possible bcoz this imax is 6 ampere, i hve tried in pb option 6 ampere 14 volt
Hey man. Just started using this today. I'm charging a NiMh 7,2 V battery for my Tamiya RC car. The battery is 3000 mAh so I set it to 3,0 A. I look at the data shown in the display while charging. At the bortom right, the mAh is showing. When it reaches 3000 it should be full. Does the charging stop automatically then? Also, top right it shows current voltage. Right now, for instance, it shows 8,73 Volts. Maybe I'm dumb but ermm... I thought a 7,2 V battery could never reach higher voltage than that exact level. What is it I don't understand?
Hey, if its a good quality battery the actual capacity will be very close to or higher than what the label says while If its a bad quality battery it could be much lower. It will automatically stop charging as soon as the fully charged voltage is reached which the charger has preprogramed in for the battery profiles. 7.2v is the nominal voltage of your battery, during loads and charging the battery will range outside this. If you have selected the correct battery chemistry on your charger, it should be doing the correct charging voltage. 8.7v does seem high to me though.
@@jbmods692 thanks for replying so fast. Upon completed charging it turned off like you said. If the voltage goes up too high during charging, is that a safety issue? The battery is all new. I did notice it got real hot during charging and stayed hot quite long.
@@magnusjohansson295 No worries, It shouldn't be hot to touch, maybe slightly warm but not hot. Reduce the current that you are charging with to 1amp or lower and see how that goes. NiMH can get hot when charging at higher currents. Double check you are using the right chemistry profile on the charger aswell.
I bought one of these a while ago and it has never worked properly. It will charge up to a point then the amps will drop to 0.1 and then suddenly discharge the battery. I can leave it for hours and it won't stop. Also the voltages it shows are wrong when I test the battery with a multi meter. I have a genuine one. Just a waste of money that was highly recommended.
I keep getting the message “connection break” does anyone know what that means? Cause it won’t do anything after that so I can’t charge my battery. Keeps me that message every time
Unless your unit is broken, it means that you have a bad connection in the way you have your battery plugged in. If you are trying to charge 2-cell and up Lipos you MUST have BOTH the main +/- leads AND the white multi pin Balance leads plugged into the correct sockets on the charger. It could also mean you have a very bad cell (or wiring break) in your battery. Check it with a cell checker.
ДЛЯ ПОКУПКИ ПО САМОЙ НИЗКОЙ ЦЕНЕ ПЕРЕХОДИ ПО ССЫЛКЕ www.avito.ru/zhukovskiy/orgtehnika_i_rashodniki/skyrc_imax_b6ac_version_2_wi-fi_-_sk-100008-11_2119171442
Even though this video is 2 yrs old it still just as relevant today. I just got this charger and even though I read through all the directions this video was a big help to understand it all. Thank You!
Being a noob in the rc jet scene can be frustrating trying to learn the ropes. Your vid was the exact opposite, quick and to the point and easy to understand, thanks!
i agree
One of the best videos for learning some basics related to battery charging. Clear, concise and to the point! 👌
Just bought a Fire Power B6AC, comes with no instructions but you have saved the day 👌👌
This video just helped me figure out how to charge my 6s2p batteries, and that awesome. Thanks for such good and clear tutorial
Finally, a video explaining this in a logical an organized way..
Good demo. I need this kind of video as i just buy a imax b6 charger. Thanks.. very easy to understand. No gimicks. just a straightforward demo. I subd as well
Thanks mate, that was my plan. To just keep it as simple as possible!
Very informative, Thanks for the guide on the charger. The time lapse of the charge was pretty cool.
I noticed you did a quick retake of what you said at around 6:40. Just lettin' you know.
Also, on rare occasion, particular chargers don't interact well with particular batteries, which is something else to take into consideration when getting a charger. It's pretty uncommon, but it's much better to catch it early rather than later.
Thanks mate and yes I missed cutting that retake haha
@@jbmods692 I put the battery to charge normally with the process you showed in the video and after 10 seconds it stops charging and throws me out and doesn't charge. I don't understand why this happens?😓
Great tutorial, concise & informative.
Many thanks!
Where can one find the XT connectors for the unit? I have no way of charging my LiPos without. Can they be purchased somewhere? THX.
Thanks for the tutorial, very useful. One question: if I want to calibrate the charger imax b6 ac ,what is the procedure? Thanks again
hai bro,if i want to charge 6000mAh 2s battery,the Amp setting is 6A or lower the better?
Nice vid just recently bought this so it’s helped me work mine
Very clear and informative video! Thank You!
What do you do if you are charging xt30 batteries and they are 450 or 550 mah. Do you put it at .4 or .5 or .6?
I hear people often say many batteries lie about the their true mAh, so how do you know what to use when charging your batteries?
Hey mate, very good question. If they battery isn't a reputable brand, I would just charge it at a max current of around 0.5amps just to be on the safer side. Then we you have done a test and know the actual capacity you can up the current.
@@jbmods692 was a good question answered very well my knowledge has been expanded thank you I'm just getting into these batteries and battery building
Hi, great video. I'm fairly new to this so excuse my ignorance. My question is, does the iMax B6ACV2 let you know when the discharge is complete?
Hey Julio, yes the charger will stop discharging and beep when the discharge process is complete if all the right settings have been entered.
I'm new to this, can you charge parallel and series batteries or a mixture of both on this charger
Could you charge a 20V 10A laptop with this charger?
So if i charge at a lower amp setting than 1c it still charges the battery the same but only takes longer ?
Yes that's correct!
What setting would you use for a single cell (3.7V) and 10 000mah capacity?
One thing I really don't like about this charger is: you can't charge a half-discharged NiMH battery, for example, without fully discharging it first. Whatever battery you're charging, you have to fully discharge it first. If I'm missing something about the operation of this device, please respond.
I just got the imax but what I'm trying to find is how to discharge an ebike battery The cable you're using on the negative positive side is the same connection can you make a video
Hi. Please can you help me out.
I have a Li-ion battery 7.4V and 1500mAh.
Firstly, do I select Lipo for charging?
My Imax charger does not have a selection for Li-ion.
I have followed your first example in your video, however, when I select Starr charging, a message appears as follows:
R: 1SER S:2SER. When I select start, an error message appears Li2S Full.
This is a brand new charger that I have bought and struggling.
Thanks, Sean
This is a great tutorial video - thank you!
No worries!
Hi so iv got this changer and iv got a 14.8v 4s 6000mah 70c battery so what amp should I set please can't find info anywhere really appreciate if you can help
These chargers can only throughput about 60watts. So you could only charge your 6000mah 4s battery at about 4amps - NOT the 6Amps of a normal 1C charging rate. So it will just take longer.
Will it stop charging the battery once the battery is fully charged or do i have to make it stop?
The charger will stop charging once it is full :) Can take some time if the charger is still balancing the individual cells.
noob question, How do I know when it's finished charging?
Hi, nice video. can you please tell us how to calibrate this charger and what is that system update when i hold ENTER and then on the charger. This system update takes so much time.
i have the fake model, but reviews seem decent, anyways i want to know if i want to balance charge my power bank, do i need to desolder the cells from parallel, then set up in series? they are in parallel, 3.7v per cell.
I have a Life battery cell that is marked as 3.2V. This charger has the Life cell settings as 3.3V. Is there a way to change that in the charger to 3.2v?
I have one like this and everything works except, charge in balance mode and balance battery . Work couple seconds and then on the screen at mah shows 0 and stay like this hours . In simple mode charge in series reach's at the end, but in balance mode charge or balance battery do nothing . You tasted yours it's ok ? Thanks
I know this video is a few years old now but just a couple questions. First off, how do you know when it's charged? I ran the battery basically dead. Car was at walking speed. Put it on the charger and the 7.4v 2s lipo was already reading around 8.4v 🤷♂️. The charger seemed to still be putting power in to it. I took it off after 30 mins. Nothing seemed to have changed much numbers wise. Also I noticed in the video you started off with a 1500mah battery and you set the capacity cut off to 1500mah. Later in the video you charged a 3300mah battery and changed the charge amps to 3.3 but didn't change the capacity cutoff from 1500. Will this be a problem. I think I did the same thing switching from my 1800mah heli battery to my kids 3300mah car battery
The charger beeps and says battery is full once done. Unless you're fast charging, it's going to take longer than 30mins to charge most batteries. The 1c charge rate is to maintain battery longevity.
The higher input voltage (8.4v) will be higher than the nominal voltage (7.4v) of the battery, that's normal.
Kupić z zasilaczem wbudowanym czy osobno? Jakieś różnice?
Can I use this to charge my 18v power tool battery..I need to check the capacity..if so how do I do it
i dont have the cord for the output... i am trying to charge an 11.1v elite soldier battery for a gel blaster. Do I need both plus in or is the the pin white plug enough?
i was wondering how do you know when the battery is finish charging, also do you have to Storage it after charging?
The charger will stop charging when the battery is full. I only put mine to storage if I am not using the batter in the next day or 2. Storage is to keep the battery at its most stable storage voltage to prolong the life of the battery and is safer than storing the battery at 100% charge.
if each cell reach a value of 4.2 voltage you battery is fully charged. There can/may be a difference of 0.1 between the cells.
Hi sir. Do you have videos for AA ni-cd and ni-mh battery using imax charger tutorial as well. Sir more power very nice videos.
Hi
Is this charger suitable for 1s battery 3.,7 volt 10000 mAh battery 30/60 C ?
Please advise
Thanks
How many amp do I charge a 8000mah with 88.8wh 3s 11.1v?
Hi, can you type the name of the cable you are using for charging? Thanks Is ths laso possible with this model to monitor the level of the charge through the App of the cellphone? Bye
Great video. Thank you
So that means I can charge 3s 3000mah lipo withing one hour with 3amps of current
How much time is needed to fully charge a battery with 5200 capacity
I'm pretty sure it depends on your charge rate.. If you charge at 5.2 amps it will take 1 hour.. If you charge at 2.6 amps it will take 2 hours. Does that seem right to anyone else?
@@bmzaron713 That is correct, generally you charge your batterys at 1c which is 1 x the amp hours of the battery. So a 5200mah would be 5.2amps and take 1 hour to charge.
I have this exact charger, will it charge my tattu 25000 mha battery safely? It's all I can afford after buying that beast of a battery.
Hey,
As long as the battery chemistry is one that the charger supports it shouldn't matter on the size of the battery. It will just take a while to charge with that big of a battery since the charger is limited to 6amps I believe. Does that all make sense?
@@jbmods692 sure does, thank you.
I just brought the exact same one but my one didn't come with power cable and has no power input wth???
Helped me allot cheers
Why after i start charging om 3.3 qmp the amperes start going down till 0.1 A
is it possible to connect the lipo on 12v battery electricity allowance and thx to u
At 8:21 in your video, it shows 5 zeros in the lower right corner -- these numbers increase over time for Pb charging -- what are they for? Not in any documentation I can find
Hey mate, those numbers are displaying how much energy has gone in or out (depending on if you are charging or discharging) in milliamp hours. Useful for seeing the actual capacity of a battery.
Hi bro new subscription here just want to ask how to charge a lipo bat with 7.4v 2s 8000mah 90c in this charger
WHEN I CHECK MY BATTERY IT SAYS 4S.... WHEN I HAVE A 6S ..... BATTERY 5200 mAH 50C 22.2 volt but i cant find out how too change the settings to 6s ???? HOW DO I DO THAT ?
how long should i put on storage mode for?
Could you post a version for nicad charging please
Can you charge a 10s with this charger?
So where the two leads go into the unit thats marked Output,,,,,, it really should say inpu seeing its the discharge lead????
Yeah i guess so :P
Just a question would this be the same with 2s shorty lipos?
Hey mate, yes will be same just make sure you don't charge over the recommended current rating. Generally 1C for lipos.
How do u tell if its fully charged
Hi man I watched your video but it didn"t answer my probmems :/
I bought the Imax B6 (for some reason it's black and not blue
And I am facing multiple problems:
When I try to "BALANCE CHARGE", it auto-detect as 2S and even when it's blinking I can't change the value to 3S-4S-5S-6S
The chager never match the cell number of my battery no matter which mode I'm in : I plug my 6S battery in and it detects 2S
On other charging modes; I can force the 6S but then, before I start the charge, it says " R = 4SER S= 6SER "
If I force the charge like so ( R = 4SER S= 6SER) the Battery voltage actually goes down as time goes by
Do you have any idea of a fix ? Or did i receive a faulty chager ?
Excelent video, thanks
BRAVOooo! BRAWOOoo! Thanks...........................!
Do you mod this to charge cylindrical cell batteries?
Hey mate,
As long as the charger has the right profile for the battery type and correct connection there should be no need to mod the charger.
What battery are you planning on charging?
How many ampere is this and can we charge car battery with this charger
Hi, you can not use this to charge a car battery. You need to buy a specific charger depending on the chemistry of your car battery that is designed for it.
The Imax B6 has a maximum output of 50w.
@@jbmods692 but there is a option to charge lead acid battery as a Pb, i think it is possible bcoz this imax is 6 ampere, i hve tried in pb option 6 ampere 14 volt
@@zoheb4you2002 Yes you are correct, sorry I was mistaken. You can charge a car battery!
Also you must use 12v setting if its a standard car battery.
Hey man. Just started using this today. I'm charging a NiMh 7,2 V battery for my Tamiya RC car. The battery is 3000 mAh so I set it to 3,0 A. I look at the data shown in the display while charging. At the bortom right, the mAh is showing. When it reaches 3000 it should be full. Does the charging stop automatically then? Also, top right it shows current voltage. Right now, for instance, it shows 8,73 Volts. Maybe I'm dumb but ermm... I thought a 7,2 V battery could never reach higher voltage than that exact level. What is it I don't understand?
Hey, if its a good quality battery the actual capacity will be very close to or higher than what the label says while If its a bad quality battery it could be much lower. It will automatically stop charging as soon as the fully charged voltage is reached which the charger has preprogramed in for the battery profiles.
7.2v is the nominal voltage of your battery, during loads and charging the battery will range outside this. If you have selected the correct battery chemistry on your charger, it should be doing the correct charging voltage. 8.7v does seem high to me though.
@@jbmods692 thanks for replying so fast. Upon completed charging it turned off like you said. If the voltage goes up too high during charging, is that a safety issue? The battery is all new. I did notice it got real hot during charging and stayed hot quite long.
@@magnusjohansson295 No worries,
It shouldn't be hot to touch, maybe slightly warm but not hot. Reduce the current that you are charging with to 1amp or lower and see how that goes. NiMH can get hot when charging at higher currents.
Double check you are using the right chemistry profile on the charger aswell.
Is there a way to tell when they’re charged?
It will say full but I wouldn’t buy this charger it overheats and will stop working after 10 charges…
@@Qsfd142 I have it already came with the truck
@@valleybuilt8979 I would get an external fan to connect to it then because they overheat and the motherboard fries itself
@@Qsfd142 thanks for the tip; mine isn’t exactly this one
I bought one of these a while ago and it has never worked properly. It will charge up to a point then the amps will drop to 0.1 and then suddenly discharge the battery. I can leave it for hours and it won't stop. Also the voltages it shows are wrong when I test the battery with a multi meter. I have a genuine one. Just a waste of money that was highly recommended.
Hey mate, if you return your faulty product they will issue a refund if it is a genuine unit.
Please sir I want circuit design of this charger
I keep getting the message “connection break” does anyone know what that means? Cause it won’t do anything after that so I can’t charge my battery. Keeps me that message every time
Unless your unit is broken, it means that you have a bad connection in the way you have your battery plugged in. If you are trying to charge 2-cell and up Lipos you MUST have BOTH the main +/- leads AND the white multi pin Balance leads plugged into the correct sockets on the charger. It could also mean you have a very bad cell (or wiring break) in your battery. Check it with a cell checker.
Is there a store mode for lipo
Hey mate, yes there is!
Super helpful tutorial but it'd be even more phenom if you did away with the irritating background music:-)
Thanks for the feedback.
What is the time frame for 1 6s battery?
Srilanka rupis
VIDEO AND SOUND OUT OF SYNC
The video and audio are fine to me, seems like just an issue on your end?
ДЛЯ ПОКУПКИ ПО САМОЙ НИЗКОЙ ЦЕНЕ ПЕРЕХОДИ ПО ССЫЛКЕ www.avito.ru/zhukovskiy/orgtehnika_i_rashodniki/skyrc_imax_b6ac_version_2_wi-fi_-_sk-100008-11_2119171442
Hi, can you use this charge to use the PS4 controller battery?
Great tutorial Thanks