Performing Submodeling in Ansys Mechanical - Lesson 6

Поделиться
HTML-код
  • Опубликовано: 21 авг 2024

Комментарии • 22

  • @AnsysLearning
    @AnsysLearning  2 года назад

    This video is part of the free Ansys Innovation Course, 'Obtaining Numerically Accurate Results Using Ansys Mechanical'. Access all of the course contents including additional lessons, handouts, simulation examples with starting files, homework problems, and quizzes: courses.ansys.com/index.php/courses/numerically-accurate-results/.
    Check out other courses on the website while you’re there. Happy learning!

  • @sergeydukman5832
    @sergeydukman5832 3 года назад +6

    Why do you apply load on the submodell one more time if the main modell is already solved with all applied loads?

  • @rupeshpatil3249
    @rupeshpatil3249 3 года назад

    Really a helpful video. Made my work easy, simple and fast.
    Thank you Sir

  • @amiraboodi2075
    @amiraboodi2075 2 года назад

    A handy feature. Thank you a lot.

  • @anthonybotting9799
    @anthonybotting9799 3 года назад +1

    At 5:31 we want RY (both axles) not equal to zero, right? I see later you set them to "Free". Good tutor. Thank you.

  • @skinfoconsultancy3787
    @skinfoconsultancy3787 3 года назад +3

    At 8:12 pedal load is applied which results in some deformation, then why is it again applied at 11:10. Doesn't it make over load than the required load?

    • @namandoshi569
      @namandoshi569 3 года назад +1

      same doubt

    • @adilasbai96
      @adilasbai96 2 года назад

      There is a load in the cut region. As I see it, if it is not applied again in the sub-model, the overall load balance would be wrong.

    • @guillaumedonnadieu3388
      @guillaumedonnadieu3388 2 года назад +1

      @@adilasbai96 but the load is infered through the deformation data I believe. So same doubt

  • @ateflaiche4436
    @ateflaiche4436 2 года назад

    Can you guide me plz to perform component mode synthesis for simple wing in ansys workbench ?

  • @kxiao9402
    @kxiao9402 Год назад

    I would like to ask how to implement the sub-model technology in transient analysis

    • @AnsysLearning
      @AnsysLearning  Год назад

      Thanks for watching! Please post your query on the Ansys Learning Forum for a detailed answer from the wider Ansys Community: ansys.com/forum.

  • @guillaumedonnadieu3388
    @guillaumedonnadieu3388 2 года назад +3

    The golden rule in ANSYS is : there will always be an Indian guy better than you

  • @ThePandazmr
    @ThePandazmr Год назад

    Why did you use a fillet of 2mm and not just split the model?

    • @AnsysLearning
      @AnsysLearning  Год назад

      Thanks for watching! Please post your query on the Ansys Learning Forum for a detailed answer from the wider Ansys Community: ansys.com/forum.

  • @icklono5
    @icklono5 Год назад

    İs there a possibility to do topology optimization on submodel?

    • @AnsysLearning
      @AnsysLearning  Год назад

      Thanks for watching! Please post your query on the Ansys Learning Forum for a detailed answer from the wider Ansys Community: ansys.com/forum.

  • @ilyagordievsky9530
    @ilyagordievsky9530 3 года назад

    Hi. Is it possible to turn on convergence for submodelling?

    • @AnsysLearning
      @AnsysLearning  3 года назад

      Thanks for watching! Visit the Ansys Learning Forum for an answer to your question.
      Visit at www.ansys.com/forum.

  • @BharathKumar-pw2xw
    @BharathKumar-pw2xw Год назад

    can anyone explain. HOW to create a Named selection like front wheel and rear wheel

    • @AnsysLearning
      @AnsysLearning  Год назад

      Thanks for watching! Please post your query on the Ansys Learning Forum for a detailed answer from the wider Ansys Community: ansys.com/forum.