Thanks! I've been having problems with the outside sealant drying up and pulling away from the stucco after 5 years on all my windows. Gonna try the CRL polyurethane to see if it's any better.
Why when I did search for installing windows this does not come up, I have to have the window distributor send me this?!?! The RUclips search is broken! This is by far the best video on installing these retrofit windows I have seen and should be at the top of the search results.
Clean work but why didn't you spray window/door foam around the inside gap between the new window frame and drywall before adding the self-adhesive trim?
Why bother? That hack install is ridiculous. They simply use cheap latex painters caulk to "seal" the window to the porous stucco - water can pour thru that assembly, so why worry about air?
@@Rlprime proper way is to completely remove the existing window - need to break out stucco 4-6" around the window to tie existing waterproofing to new window assembly. Otherwise, you're not doing a damn bit of good, and most likely creating a bigger problem. Why this hack contractor is able to get away with such laughably shambolic installs is because his windows rarely see rain in Arizona. In wet climates, those windows would leak like sieves. In Arizona, they still leak, but it's mostly hot air infiltrating expensive-to-cool interiors. But they 'look' good and unsuspecting victims, er, customers are none the wiser.
@@ArthurDentZaphodBeeb his install was fine. They didn't break the original vapor barrier. They Caulked behind the z bar. I didn't see what ceiling he used, though. They did use a textured polyurethane to finish the caulking on the outside. That stuff absolutely needs to be painted, because it attracts dirt and looks like crap in no time. It is not going to leak water. He should have foamed around it, though. He also should have shimmed under the track, because if you don't, over time the weight of the sash is going to bow that crappy vinyl frame down. It's going to screw up your reveal between your sash and your jamb, and it's going to pop off your crappy vinyl trim quick. It's also going to generate a warranty call, because now there's daylight between the sash and the jam in the upper corner, because this frame is sagging at the bottom in the middle.
Very helpful video but like other people is mention the weather seal from inside is very importan also, most of costumers replace their windows to be more efficient and foam weather strips or foam sprayed definitely will improve your values.
Good video, very instructive I'm going to be installing 2 retro windows that way ...I do it the old way by cutting the stucco & then I have to re-stucco a lot more work I have videos on that on my RUclips channel. Thanks for the tips now I should be able to install a window in under an hour rather than 2 days.. I will make a video on that & I will give you a shout-out. Thanks again.
Great video, Great looking window, nice looking caulk lines and it surely covers the stucco installation process very well!! I am curious about a few small details that could have been covered here for the home owners attempting to install stucco windows in their homes by themselves and using this video as a guide. Maybe this step was not included in the video during a cut sequence? Was the insulation added between the vinyl and interior walls prior to install of the interior trim?
Excellent video! I like the idea of keeping as much glass as possible. Can I also cut the top and bottom fin? I don't mind grinding them off causing dust and debris.
Depending on the type of frame you have, you may wish to avoid grinding the base channels too much. Most of the frames are made square channel with fins that are embedded into the stucco. You can risk revealing those fins by grinding too much of the frame down.
Thank you for the video - installers here want to rip out the old frame and make a mess of my stucco. Although I would do some different area protection and final detailing; the video was well made and informative and will save me hundreds... at least.
In the case of a 2nd story: Is it necessary to stand outside (as on scaffold)? Or can this procedure be executed exclusively from inside the wood-frame, stucco building? There are a lot of these in southern California and I own one.
When you put the window in the opening, you used caulking to hold the window in place. I did not see you use any fasteners on the inside or outside to hold the window in place. Is this window held in place by caulking only?
What would your approach be on a home with stucco and wood window frame that have a wood brick mold that is fastened to the exterior wall as well as the window for mounting ?
Curious how do you like the Simonton Product? I've been thinking of using them for the EXACT SAME APPLICATION 😄😄😄 Using their Madera Series in Bronze...
Why wouldn't you cut your interior trim at 45 degrees for a cleaner corner to match the window frame itself, and maybe I missed something but I didn't see any insulation go in before the interior trim was put on. Otherwise looked pretty good.
Good video, but I think you left one very important step out, the weep holes at the bottom, they should be left uncaulked so water doesn't sit inside the bottom rails... no?
I've been doing Windows for 25 years . tape the caulk? because you can't caulk? then when you pull the tape your caulk pulls too and shows the tape line and sticks up. This type of installation is called jump frame and you are suppose to use foam insulation before you put on your flat trim inside.. also you you need to lay a bead of caulk/lock tight on the window before you put your trim, to hold it.. the tape on the flat trim will fail and not stick to the window.. Then you have a service, which I'm sure your use to. horrible
I wish I could see how he removed the side fins. What kind of a tool does he have there? How do I remove the side fins please! I have an aluminum frame. I"m having to grind them out? Thanks
looked like a small break for ductwork, you can class/p it on the aluminum and bend it back and forth the aluminum will work harden from the bending and snap off
Here is the problem with his exterior caulking. He is putting a small bead at the ends of the window frame as the vinyl expands and shrinks (a lot) It will pull the caulk and you will have a leak. I just redid neighbors windows that the caulk failed and there were hugh gaps. Caulking is a piss poor material to seal out water. It just is. Mechanical IE a piece of trim is much better. The edges of the frames like the tip of your finger is not enough grab. It will open (ask how I know) Plus caulk has a certain ability to flex. Gotta research one that will flex enough.. Still it will leak, (suckers bet) Did you know your homeowners insurance has removed mold and mildew damage from its coverage! Makes a lot of sense when you see this installation.. Then you used NO freakin window foam around the frames and only have a thin piece of vinyl trim( speachless) Great r factor your getting there(not getting) Then to use caulk on the inside of the window that will discolor and attract dirt. Now that has to be painted so you will have a amateur hour look.. Remember the original windows were put in under the stucco and for a really good reason.. I restored homes for a living and this aint it.. Remember most contractors go out of business every 7 years or so then restart under a new name to avoid the warranty and damage claims.. I was a kitchen salesperson and other division did anderson windows.
This company is scamming every customer. Looks like they are using a cheap latex caulk against that rough old stucco and expecting it to be watertight? It would be laughable if it weren't so contemptuously pathetic. In this vid, at least the window is covered by the porch above, but heaven help any window that is exposed to driving rain with a southwest exposure.
Awesome video. I’m thinking of replacing some arched windows in my home but was gonna break the stucco and install flashing due to humidity in the inside. Do you think it’s better just to do this ?
I guess you don't foam the existing aluminum window on the inside? Not sure isn't that why people replace the aluminum windows? Due to exterior weather transfer?
1.I don't think you want to tell your costumers you want to cut corners and get the easy way out like you said on your video. It would be nice if you would slow down on the process instead of jump or forward from the begging to the end, that's the part I want it to see. Why you didn't insulate around the gab window before install the inside trim
+Art Rios He says maintaining the max amount of glass can't be done by taking short cuts or the easy way out. It's primarily a commercial for his company not a DIY video. I'm looking for a DIY video myself and I am with you 100% wondering why he left that big air space around the window. I think I would have spray foamed it before trimming it up.
@@mcola6397 Haha! Seriously? There’s no way it only takes an hour per window, right? My landlord’s changing every window in my apartment tomorrow and this replacement looks very similar to my building: stucco, same kind of windows, etc. She’s saying they can do two apartments per day, seven windows in each apartment. I’m guessing they’ll get half done in a work day. Hope I’m wrong.
I am going to be replacing my aluminum windows to vinyl, and I cannot figure this out for the life of me. My windows (MI) are recessed in stucco. There's about 1/4 inch of stucco that covers the small flanges that protrude from the sides of the window. There has to be a better way than chiseling out the stucco from around every window and then replacing it. someone said to just tear out the old window by taking the glass out first then twisting, cutting and bending the frame out. If that is true, then how the heck can the new one fit?
You lose a few inches of window opening when you use this type of replacement window. You have to order the window to slip inside of the old frame. You have to figure out how big a window you can stuff in there after removing whatever metal you can. If you do this yourself, make sure you put shims under the track, because it will sag over time otherwise.
This guy really doesnt like any other company doing what he does but why did you not miter the corner trim pieces that you installed at the end square cuts look like crap
Who care what other companies do, worry about the services you provide. If you keep comparing yourself to the competition your just showing how insecure you are in the services you provide.
This is a joke, right? Just use a cheap caulk to seal the frame against the stucco??? I'd love to see your contract and all the exculpatory language you used to not have your backsides sued into the next century. Unbelievable.
Silver line is a l;ow end window to say the least. if i had enough money i could win that award easy. just a new Construction grade window replaceable in about 10 yrs
One of the best video's on window replacement that I've seen. Thank you
I would miter the flat trim on the interior... easy to do and cleaner looking. Thanks for the video on retrofitting windows.
Thanks! I've been having problems with the outside sealant drying up and pulling away from the stucco after 5 years on all my windows. Gonna try the CRL polyurethane to see if it's any better.
No spray foam before the inside trim?
Man that’s good work. Thanks I’m using this as a refresher course for my house.
Why when I did search for installing windows this does not come up, I have to have the window distributor send me this?!?! The RUclips search is broken! This is by far the best video on installing these retrofit windows I have seen and should be at the top of the search results.
Great video and instruction! I am now confident in doing my own windows myself. Thank you!
Lol
Clean work but why didn't you spray window/door foam around the inside gap between the new window frame and drywall before adding the self-adhesive trim?
Why? Aluminum Is A Great Thermal Break
lol
Why bother? That hack install is ridiculous. They simply use cheap latex painters caulk to "seal" the window to the porous stucco - water can pour thru that assembly, so why worry about air?
ArthurDentZaphodBeeb so what’s the proper way?
@@Rlprime proper way is to completely remove the existing window - need to break out stucco 4-6" around the window to tie existing waterproofing to new window assembly. Otherwise, you're not doing a damn bit of good, and most likely creating a bigger problem. Why this hack contractor is able to get away with such laughably shambolic installs is because his windows rarely see rain in Arizona. In wet climates, those windows would leak like sieves. In Arizona, they still leak, but it's mostly hot air infiltrating expensive-to-cool interiors. But they 'look' good and unsuspecting victims, er, customers are none the wiser.
@@ArthurDentZaphodBeeb his install was fine. They didn't break the original vapor barrier. They Caulked behind the z bar. I didn't see what ceiling he used, though. They did use a textured polyurethane to finish the caulking on the outside. That stuff absolutely needs to be painted, because it attracts dirt and looks like crap in no time. It is not going to leak water. He should have foamed around it, though. He also should have shimmed under the track, because if you don't, over time the weight of the sash is going to bow that crappy vinyl frame down. It's going to screw up your reveal between your sash and your jamb, and it's going to pop off your crappy vinyl trim quick. It's also going to generate a warranty call, because now there's daylight between the sash and the jam in the upper corner, because this frame is sagging at the bottom in the middle.
Very helpful video but like other people is mention the weather seal from inside is very importan also, most of costumers replace their windows to be more efficient and foam weather strips or foam sprayed definitely will improve your values.
Good video, very instructive I'm going to be installing 2 retro windows that way ...I do it the old way by cutting the stucco & then I have to re-stucco a lot more work I have videos on that on my RUclips channel. Thanks for the tips now I should be able to install a window in under an hour rather than 2 days.. I will make a video on that & I will give you a shout-out. Thanks again.
Can you elaborate on how you removed the inside aluminum fin? Did you scribe with a razor knife and then use a sheet meet flanging tool to remove?
Great video, Great looking window, nice looking caulk lines and it surely covers the stucco installation process very well!! I am curious about a few small details that could have been covered here for the home owners attempting to install stucco windows in their homes by themselves and using this video as a guide. Maybe this step was not included in the video during a cut sequence? Was the insulation added between the vinyl and interior walls prior to install of the interior trim?
9 years later - thanks for this
Before you put the inside trim on wouldnt it be best to spray some insulating foam inside
Do you do anything about the edges of the new trim showing? I didn't see anything to conceal that.
I dont see insulation between the window jambs and window frame.
Dont you have to leave a gap in the caulking for condensation?
Normally, in Los Angeles area, the bottom caulking should be left out to allow moisture to escape. Is this not the case in Arizona?
Excellent video! I like the idea of keeping as much glass as possible. Can I also cut the top and bottom fin? I don't mind grinding them off causing dust and debris.
Depending on the type of frame you have, you may wish to avoid grinding the base channels too much. Most of the frames are made square channel with fins that are embedded into the stucco. You can risk revealing those fins by grinding too much of the frame down.
Thank you so much. There was this company who wanted 11,000$ to replace my windows
Thank you for the video - installers here want to rip out the old frame and make a mess of my stucco. Although I would do some different area protection and final detailing; the video was well made and informative and will save me hundreds... at least.
Avoid these hacks like the plague.
I noticed no non expanding insulating foam was used in the large gap at the top
How do apply sunscreens to these windows? I've always heard vinyl never stands up to the desert sun.
You can install glass instead of vinyl
How was the window attached on the inside?
love your video I'm new to the makeover blog edition, and would really love to share this on my site. Can I use your video to embed it on my site?😀
What screws did you use?
In the case of a 2nd story: Is it necessary to stand outside (as on scaffold)? Or can this procedure be executed exclusively from inside the wood-frame, stucco building? There are a lot of these in southern California and I own one.
When you put the window in the opening, you used caulking to hold the window in place. I did not see you use any fasteners on the inside or outside to hold the window in place. Is this window held in place by caulking only?
They did drill the frame in place. That’s by the vinyl cover for the holes
no foam insulation y ????
Beautiful job; your pride in your work shows.
What would your approach be on a home with stucco and wood window frame that have a wood brick mold that is fastened to the exterior wall as well as the window for mounting ?
How come you didn’t foam the gap before closing up
Curious how do you like the Simonton Product? I've been thinking of using them for the EXACT SAME APPLICATION 😄😄😄 Using their Madera Series in Bronze...
Do you have an office in Las Vegas?
Is that a white sanded polyurethane caulk??
Great idea! I think about it how to safe stack. Thanks!
No backer Rod?
Why wouldn't you cut your interior trim at 45 degrees for a cleaner corner to match the window frame itself, and maybe I missed something but I didn't see any insulation go in before the interior trim was put on. Otherwise looked pretty good.
Can you replace this style window with a Jeld block frame?
Can you remove the window shims after the foam is dry?
How would you do a installation with the foam stucko pop out trim around the window??
Ever used CWS?
Good video, but I think you left one very important step out, the weep holes at the bottom, they should be left uncaulked so water doesn't sit inside the bottom rails... no?
I've been doing Windows for 25 years . tape the caulk? because you can't caulk? then when you pull the tape your caulk pulls too and shows the tape line and sticks up. This type of installation is called jump frame and you are suppose to use foam insulation before you put on your flat trim inside.. also you you need to lay a bead of caulk/lock tight on the window before you put your trim, to hold it.. the tape on the flat trim will fail and not stick to the window.. Then you have a service, which I'm sure your use to. horrible
Can you link to a better video on how to do this? Thanks for the insight.
Piggy backer
I wish I could see how he removed the side fins. What kind of a tool does he have there? How do I remove the side fins please! I have an aluminum frame.
I"m having to grind them out? Thanks
looked like a small break for ductwork, you can class/p it on the aluminum and bend it back and forth the aluminum will work harden from the bending and snap off
"hand seamer"
It looks like the other guy is cutting it first. Is that just a utility knife?
Excellent video, thank you. Do you work in Phoenix or can you recommend someone who provides your level of expertise?
Signature Glass & Mirror is a great company out of Phoenix.
Here is the problem with his exterior caulking. He is putting a small bead at the ends of the window frame as the vinyl expands and shrinks (a lot) It will pull the caulk and you will have a leak. I just redid neighbors windows that the caulk failed and there were hugh gaps. Caulking is a piss poor material to seal out water. It just is. Mechanical IE a piece of trim is much better. The edges of the frames like the tip of your finger is not enough grab. It will open (ask how I know) Plus caulk has a certain ability to flex. Gotta research one that will flex enough.. Still it will leak, (suckers bet) Did you know your homeowners insurance has removed mold and mildew damage from its coverage! Makes a lot of sense when you see this installation.. Then you used NO freakin window foam around the frames and only have a thin piece of vinyl trim( speachless) Great r factor your getting there(not getting) Then to use caulk on the inside of the window that will discolor and attract dirt. Now that has to be painted so you will have a amateur hour look.. Remember the original windows were put in under the stucco and for a really good reason.. I restored homes for a living and this aint it.. Remember most contractors go out of business every 7 years or so then restart under a new name to avoid the warranty and damage claims.. I was a kitchen salesperson and other division did anderson windows.
This company is scamming every customer. Looks like they are using a cheap latex caulk against that rough old stucco and expecting it to be watertight? It would be laughable if it weren't so contemptuously pathetic. In this vid, at least the window is covered by the porch above, but heaven help any window that is exposed to driving rain with a southwest exposure.
Can you also remove top and bottom fins?
I’d like to know how this actually worked out after he left and months later… homeowners happy?
How do you take the middle bar out?
Two screws on the outside
all that work and you did not spry any insulating foam on the interior side frame of the window?
Awesome video. I’m thinking of replacing some arched windows in my home but was gonna break the stucco and install flashing due to humidity in the inside. Do you think it’s better just to do this ?
The lack of flashing will not cause the window to get foggy inside. I can cause water leaks when it rains though.
I guess you don't foam the existing aluminum window on the inside? Not sure isn't that why people replace the aluminum windows? Due to exterior weather transfer?
You need insulation foam before you put the interior trim on
The music sounds like 80's love music
you are taking the cheap and easy way out by leaving the old frame.....?
What is the brand you are using?
It is funny how every window company does something that separates them from the rest.
Great video.....but you are not showing how to apply the screws on the windows.....but still is a great video.....
what is that tool you use to cut out the aluminum fin?
"hand seamer"
Excellent video. Very instructive.
Does this comply with AAMA 2410-13?
Doesn't comply with anything other than ripping off unsuspecting customers. This 'installation' is a total farce.
Nobody gives a shit. It's just a window. Not fucken brain surgery. Relax. Almost anyone can do this.
name of song please. good presentation and skill
Daimonion - hallucigen🎶
1.I don't think you want to tell your costumers you want to cut corners and get the easy way out like you said on your video. It would be nice if you would slow down on the process instead of jump or forward from the begging to the end, that's the part I want it to see. Why you didn't insulate around the gab window before install the inside trim
+Art Rios He says maintaining the max amount of glass can't be done by taking short cuts or the easy way out. It's primarily a commercial for his company not a DIY video. I'm looking for a DIY video myself and I am with you 100% wondering why he left that big air space around the window. I think I would have spray foamed it before trimming it up.
Mike Hixson spray foam is full of what?
no foam in the gap before trim ,mmmm? no masking the room when you cutting whit the grinder dust go inside the room,mmmmm? ayayayyyyy!! intersting
DJ Oscar lol
Should this guy have used wood filler?
How long, on average, does it take to replace a window this size?
1 hour
@@mcola6397 Haha! Seriously? There’s no way it only takes an hour per window, right? My landlord’s changing every window in my apartment tomorrow and this replacement looks very similar to my building: stucco, same kind of windows, etc. She’s saying they can do two apartments per day, seven windows in each apartment. I’m guessing they’ll get half done in a work day. Hope I’m wrong.
Paintable caulking got it
I am going to be replacing my aluminum windows to vinyl, and I cannot figure this out for the life of me.
My windows (MI) are recessed in stucco. There's about 1/4 inch of stucco that covers the small flanges that protrude from the sides of the window. There has to be a better way than chiseling out the stucco from around every window and then replacing it. someone said to just tear out the old window by taking the glass out first then twisting, cutting and bending the frame out. If that is true, then how the heck can the new one fit?
Did you get it figured out?
@@r2ba435 I did. Angle grinder to the stucco, cut out enough to wiggle the frame free.
what do you call the interior trim and where can I get some?
Rwd
Couldn’t you just use a mallet and flatten the fins?
nice... Thanks....
I think u just saved me thousands of dollars ...I supposed the new windows were slightly smaller? Send me an answer if u can
You lose a few inches of window opening when you use this type of replacement window. You have to order the window to slip inside of the old frame. You have to figure out how big a window you can stuff in there after removing whatever metal you can. If you do this yourself, make sure you put shims under the track, because it will sag over time otherwise.
This guy really doesnt like any other company doing what he does but why did you not miter the corner trim pieces that you installed at the end square cuts look like crap
Cool film.
This guy made himself look he goes over and beyond for his customers. But this is an average window install. I'm sure he over chargers.
you didnt show every detail.
Everyone’s asking about insulation and mitre cuts but I’m wondering what happened to his bottom tooth 😬
Cheap nasty trim you call that good
Well, you sped up the most important part and didn't even explain the steps of removal and installation, not good.
No foam ha lmao
You skipped over the parts i needed to see
Lol. He skipped the parts he doesn't want anyone to see. Complete hackery.
Pure Mickey Mouse
Some other company
Some other company....
That’s a cheap way to do a window
Who care what other companies do, worry about the services you provide. If you keep comparing yourself to the competition your just showing how insecure you are in the services you provide.
This is a joke, right? Just use a cheap caulk to seal the frame against the stucco??? I'd love to see your contract and all the exculpatory language you used to not have your backsides sued into the next century. Unbelievable.
What would you have done differently? Could you please direct me to the correct way.
Junk silverline window..
Silver line is a l;ow end window to say the least. if i had enough money i could win that award easy. just a new Construction grade window replaceable in about 10 yrs
How long, on average, does it take to replace a window this size?