FULL FLOW VW engine case - How I DIY
HTML-код
- Опубликовано: 21 дек 2024
- VW Gasket set amzn.to/3YQY7Jk
3/8 to 8 an amzn.to/3NJowUM
8AN Male Flare to 1/2" NPT amzn.to/3RQeT8e
2 PCS Metals Brass Pipe Fitting 90 Degree Barstock Street Elbow 3/8" NPT amzn.to/4aESrXY
carbide set amzn.to/48zGLnE -
-
-
breather hose amzn.to/48nWYff
Happy 2024, Mike & family and everyone here. I remember Gene Berg’s method for drilling for full flow with the engine in the car. You would tap the case using grease to keep the metal particles out of the galleys. Adventurous! 😉
Great video, Mike, thank you for taking out the time to do it
I recommend clamping the case and using a drill press. The drill bits can pull into the material really fast with a hand drill and throw your unsecured case in turn cracking the hole you’re drilling very easily. I also recommend using a reamer before tapping to again prevent cracking Also Rocky Jennings among others I’m sure sell a nice little tool for clearance the case for the brass 90
I used Empi aluminum plugs because they will expand and contract at a rate a Lot closer with the mag case but you have to be careful and have quality Allen wrenches because they can strip pretty easy
Rockys kit and drill press do a much better job.
I didnt feel out of control at all just catches easily. then I would back it off and let the speed do the work. Not hard at all to do with a regular drill. I just would not use a plug in drill. cordless just does not have enough power to do any damage IMO.
Nice job on the full flow! Good points on where the oil pumps leak. I still have all my taps for all that.
Thanks 👍
👍 Can you make a video on replacing all the type 1 case plugs?
Nice, the case i used for my baja came like this. I am gonna do this for my square back engine I'm building.
Thanks for making this!
Thanks Mike, I was looking for info on What kind of plug to use after pulling the OG plugs. I see aluminum ones, brass ones and steel. Ok on the Steel ones. Thanks again.
Nice video Mike - thanks for sharing. Enjoy the rest of the week - Happy New Year too🎉💥😊
Hey Mike ! H N Y ! off subject I watched your # shorts video on the Brothers reground hp cams yesterday ? I commented back that they use to flycut the heads to compensate for the valve adjust > I thought about it some more and it is possible that the reground lifters gets rid of distance . You would not believe the stuff they did back in the 60s . On p/cs they would expand the piston .010 and hone bore the cyl. and put .010 rings which made a 87mm and they had green tipped wrist pins that were .005 over sized and would hone the piston and rod without replacing bushing . fix it right up !
If the pimp is to loose to the case get a cast iron pump and solder around the pick up hole and the exit hole then shoe shin it with emery cloth till it is in , even if it take 2X to get it right . my 1999 Autolinea case went from 4 lbs hot to 45 lbs hot . When you put a motor together with all new parts and aint got no oil pressure try this out . How to check if this is the problem is take the 4 oil pump studs out and tighten the case mine would rattle ? Your oil pump should have to be beat in with a block of wood and hammer = interference fit but loosen case knock it in the tighten final .
excellent Jimmmy....good stuff there. make sure that pump fits tight.
I’ve accidentally lit off some of that mag dust. Scared the crap out of me
yea ignites fast. always clean up as you work. best advice.
hi, does this work on a type 2 as well I have a 63 bus,, I need help!
Do you have any experience or talked to anyone that has used the CB in & out pumps where you don’t need to drill for full flow? It seems like a good idea, but I don’t see much feedback on the web or RUclips. I understand how they work so it seems like a no brained to use one instead of doing all the drilling and tapping but it doesn’t seem very common.
Excellent and informative video!
Unfortunately some sellers on amazon and sometimes amazon do not like to send to Puerto Rico. Not having anybody in the US, most of the time I have to rely on whatever I can find in the Island. Overpriced!
OH man that sucks. Shipping must be HELL too. Cip 1?
@@Mikefngarage , yup. Trying them now, and CarCraft. Shipping is a Keller. Even though we are part of the US, where I can send parts in a USPS Priority box,no matter how heavy, they rather charge more shipping.
Bit scared too drill into a case. But does this mod help keep the motor cool for longer drives? Does oil pump gears differ in size? Can the original oil cooler be removed too use the remote oil cooler for longegevity? As my my bug is a daily and live in South Africa
Hey Mike, the drill and tap set info?
Just two layers of Teflon tape, seals and does not increase the torque placing the plug. Old oilfield hand.
Id that a German case?
AN fittings are expensive be aware of that.
don't forget to put that tiny pulley tin on before you put the crank pulley back on, that's a pita, ask me how I know.😂