*Coming up on having had this saw for a year....am a casual user and bought it to cut up sections for bowl blanks. Easy to start, **Bestfor.Garden** also recommend even after storage for a couple of months. Simple chain tension adjustment. Just cut up some 20" Osage Orange, including ripping bolts in half (at an angle). Like butter!*
What a lot of people don't realize is that when it's hot & has been shut off, you need to pull the choke out, THEN PUSH IT BACK IN. That sets the high idle & it should start. If you don't do this, you'll crank it forever.
The Husqvarna 235 and 240 are the biggest pieces of junk ever made. Husqvarna should have recalled every one of them. They have an unfixable defect from the factory that cannot be fixed.
Great videos A-1. I've had one of these E-240s since 2008 and its worked flawlessly since then. Only service I've had to do over the years was fuel lines and air filter. In fact I'm still running the factory spark plug. After 9 years Finally starting to have carb problems though and would like to pull it and clean it if not go ahead and replace it. I'd love to see a video showing how to properly crack the case for the purpose of cleaning/replacing the carburetor.
I've had several chainsaws but mine ran for an hour and quit, never would start again. I expect the coils are poor quality. At least test it out for a few hours before the store return policy expires.
have had 4 of these, ya FOUR- all warranTY, all failed because air was getting into fuel line, which degraded from cold. These plastic fuellines and plastic primer bulb especially, do not like to freeze, or excess sunlight, because the cheap plastic degrades and ends up leaKing, and you lose prime as air enters fuel line from cracks....., this is the worst part of the design...., good luck fixing.... i have worked in mineral exploration and tree falling and have used saws extensively for fuel wood cutting and saw mill. My sTihL 038, is over 20 years old and runs and starts like a dream, but for lighter work, wanted a saw that wasn'T 13 lbs.
Make sure the bar brake is OFF to take this a part to clean it. It is a B**** if you don't! I had to take mine to a shop to reset it. It is not like a Stihl for that.
Not if you want to run one for more than an hour! A tank of gas lasts about half hour, so after 2 tanks of gas it won't start again until it cools off. I have a 240 but other Husqvarna owners complain about the exact same thing...won't start when hot.
I know this is late, but EXACTLY what Ken said. I bought one to replace a stolen Jonsered. When it runs, it cuts like a beast. Trouble is keeping it running while idle. Also, instructions say to purge the gas line 6 times, I think. I usually hit the bubble like 12 times. When cold, it starts right up. But you better cut fast, and hope you don't have to stop in the middle of your work. Next time I buy a saw, it will not be a husky. Hope this helps someone out there looking for some answers about saws. As a side note: When I was a kid, my dad bought a Stihl 029, and ran it for well over 20 years...
The saw doesn't run very long. It will shut off several times, it will idle but once you press the throttle it will kill. When it does run, the fly wheel is garbage and will cause problems. It leaks bar oil like the exon Valdez. Don't waste your money like I did.
Husqvarna stuff is cold blooded. I just started mine up because I have to use it for my wife’s ass hole hair. Anyways I had to change the chain cuz I struck mud and dirt. Thanks for the help
@@IMiss_The90s I got mine from a frustrated guy. I set the mixtures right, and now I have the hardest pulling sub - 40cc saw I've ever run. Tiny torque monster it is.
240e husky all i get done is replaceing flywheel sheers off the keyway inside the flywheel dont like this saw at all all well most stuff is plastic junk anyways
I bought this saw brand new. It either won't start. Or. Bogs out and shuts off. Then. Won't restart. Nothing but issues since new. Only on 4th tank of fuel. I'll never buy another husqvarna. Their customer service is non existent.
i have had this particular chainsaw for about 3 years now, purchased from the southern states co-op which is now out of business. I purchased in a pinch to aid with limbing, small cuts when someone was coming over to help me work. I have had a number of issues with the throttle linkage, maybe its streched; also had to purchase a new side plate that has the brake, the bar tensioner is a terrible design, held on only by a plastic tab. It is not running now, or atleast not well. Once you get it started, it will run for a few minutes then shut off, I wonder if the cylinder head is bad...
*Coming up on having had this saw for a year....am a casual user and bought it to cut up sections for bowl blanks. Easy to start, **Bestfor.Garden** also recommend even after storage for a couple of months. Simple chain tension adjustment. Just cut up some 20" Osage Orange, including ripping bolts in half (at an angle). Like butter!*
What a lot of people don't realize is that when it's hot & has been shut off, you need to pull the choke out, THEN PUSH IT BACK IN. That sets the high idle & it should start. If you don't do this, you'll crank it forever.
The Husqvarna 235 and 240 are the biggest pieces of junk ever made. Husqvarna should have recalled every one of them. They have an unfixable defect from the factory that cannot be fixed.
Best chainsaw I've ever own . Just keeps ON running. I run it with carbid tipped chain . Costs more but never seems to need sharping.
Great videos A-1. I've had one of these E-240s since 2008 and its worked flawlessly since then. Only service I've had to do over the years was fuel lines and air filter. In fact I'm still running the factory spark plug. After 9 years Finally starting to have carb problems though and would like to pull it and clean it if not go ahead and replace it. I'd love to see a video showing how to properly crack the case for the purpose of cleaning/replacing the carburetor.
How about 15 years later? How’s she running??
Where can I find parts for 240S 60 yrs+- old made in sweden??
Great video! Excellent editing and very informative. Thanks for keeping it very to-the-point. If i lived in Illinois, I’d buy from you guys!
you forgot to explain the procedure concerning the clutch brake . It has to be released before removing side cover !
That was really awesome. Thanks for not telling or showing where the bar oiler adjustment is.
I don’t know if this model has an adjustment screw on it
Doesn't have one
I've had several chainsaws but mine ran for an hour and quit, never would start again. I expect the coils are poor quality. At least test it out for a few hours before the store return policy expires.
Thank you this was very helpful!
have had 4 of these, ya FOUR- all warranTY, all failed because air was getting into fuel line, which degraded from cold. These plastic fuellines and plastic primer bulb especially, do not like to freeze, or excess sunlight, because the cheap plastic degrades and ends up leaKing, and you lose prime as air enters fuel line from cracks....., this is the worst part of the design...., good luck fixing.... i have worked in mineral exploration and tree falling and have used saws extensively for fuel wood cutting and saw mill. My sTihL 038, is over 20 years old and runs and starts like a dream, but for lighter work, wanted a saw that wasn'T 13 lbs.
Try figuring out how to stop so much bar oil coming out....good luck. Pours the stuff nnooooo ADJUSTMENT.
Make sure the bar brake is OFF to take this a part to clean it. It is a B**** if you don't! I had to take mine to a shop to reset it. It is not like a Stihl for that.
Is this saw good
Not if you want to run one for more than an hour! A tank of gas lasts about half hour, so after 2 tanks of gas it won't start again until it cools off. I have a 240 but other Husqvarna owners complain about the exact same thing...won't start when hot.
I know this is late, but EXACTLY what Ken said. I bought one to replace a stolen Jonsered. When it runs, it cuts like a beast. Trouble is keeping it running while idle. Also, instructions say to purge the gas line 6 times, I think. I usually hit the bubble like 12 times. When cold, it starts right up. But you better cut fast, and hope you don't have to stop in the middle of your work. Next time I buy a saw, it will not be a husky. Hope this helps someone out there looking for some answers about saws. As a side note: When I was a kid, my dad bought a Stihl 029, and ran it for well over 20 years...
I love mine, I don't buck or fell with it though. Easy to flip around for limbing. I haven't had any mechanical issues.
The saw doesn't run very long. It will shut off several times, it will idle but once you press the throttle it will kill. When it does run, the fly wheel is garbage and will cause problems. It leaks bar oil like the exon Valdez. Don't waste your money like I did.
Love mine cuts and runs really good never a problem cuts around 10 cord of wood every year!
are these a Poulan ?
Yes
No it is not, while Husqvarna does own Poulan the x-torx engines in their consumer grade saws are not found in any Poulan labelled saws.
Electrolux owns husqvarna , jonsored and poulan
Husqvarna stuff is cold blooded. I just started mine up because I have to use it for my wife’s ass hole hair. Anyways I had to change the chain cuz I struck mud and dirt. Thanks for the help
Brooo 😂😂😂😂
@@offroadwithtoad1986 5 years later it’s a mess still getting it out the way
anybody know if there is an oiler adjustment screw??? mine is spewing oil as it sits while idling.
tyhnbgtyhnbgt did you ever find any info on this? I am here for the same reason. I am having problems finding any information on it.
Mines the same way. I haven't found an adjustment.
Their is no adjustment of the oiler. The oil pump worm gear is driven directly of the crankshaft, and will oil whenever the engine is running.
@@davidoakley3256 I sold mine today. Had enough of it. Most unreliable saw I ever had. So frustrating.
@@IMiss_The90s I got mine from a frustrated guy. I set the mixtures right, and now I have the hardest pulling sub - 40cc saw I've ever run. Tiny torque monster it is.
240e husky all i get done is replaceing flywheel sheers off the keyway inside the flywheel dont like this saw at all all well most stuff is plastic junk anyways
You don't see me with a worn out chain often!
I bought this saw brand new. It either won't start. Or. Bogs out and shuts off. Then. Won't restart. Nothing but issues since new. Only on 4th tank of fuel. I'll never buy another husqvarna. Their customer service is non existent.
i have had this particular chainsaw for about 3 years now, purchased from the southern states co-op which is now out of business. I purchased in a pinch to aid with limbing, small cuts when someone was coming over to help me work. I have had a number of issues with the throttle linkage, maybe its streched; also had to purchase a new side plate that has the brake, the bar tensioner is a terrible design, held on only by a plastic tab. It is not running now, or atleast not well. Once you get it started, it will run for a few minutes then shut off, I wonder if the cylinder head is bad...
Amen brother. Piece of junk!
Biggest piece of junk saw ever! So many videos on this thing and all the stuff you have to do to keep it running!!
Junk junk junk junk
Hire a proper camera operator next time ..terrible sound and the camera cut the presenters head off