Yes, I’ve included the User Manual page numbers in the chapters for reference. Thanks to Sovol’s clear presentation, the assembly wasn’t much of a challenge, but my video could hopefully save a few minutes for the new SV08 owner community.
I have to say your videos are very informative and the extensions for the sovol sv06 and SV07 as well as for the T300 are simply great .Would love to see some of your print profiles for the Sovol series .With best regards, Jean from Belgium
That's an easy upgrade. With the exception of my SV07+ I've replaced the board cooling fans in all my printers for quieter ones. SV07+ comes with temperature controlled fans, which is a game changer. The SV07/Plus is such an underestimated device. But I have to say, this idle mode fan noise is the only negative I can say about the SV08. Sovol team really did their best here!
nice assembly vid!! you're funny; lemme ground myself then walk back to the unit!! haha at least ya have the sense to do it!! thank you for taking the time! to make this video!!!
I got mine a few days ago. Already did some changes (they are not nessasary, but nice2have): 1. The original eMMC is just 8GB, wich limits the number of space for gcode and timelapses. As as the lazy guy I am, I never clear up anyway. So I copyed the firmware to an 32GB (from Qidi...). The filesystem expands automaticly. So just make a backup of original eMMC and write it to the new one. Cost about 24€. 2. The controllerboard fan was replaced by an Noctua 24V 4010. 3. I ordered the Revo coldend the next Layer had designed for the SV08. However, I can not recommend this. The tollerances are not perfect, I had to postprocess a bit. This went wrong. The coldend is now not perfectly perpendicular to the bed - and the nozzle (the heatbreack part) bended. Destroyed 2 Revo nozzles (they still work, but definitly not usable in other hotends anymore). However, on printables is a design for an Adapter to use Bambulab X1C/P1P/P1S coldends on the SV08. So I now ordered the Biqu Panda Revo for the P1S to try it with this adapter. 4. Just got the Biqu microprobe. Will try it next weekend. But actually the Revo nozzles are so precise manfactured, I do not think I have to recalibrate z-offset often anyway. 5. The BTT 5 inch HDMI Touchscreen works quite well. With 38€ quite affordable. However, I also ordered an 11€ HDMI foil-cable to route HDMI invisible from the ouside port back into the printer and internaly to the display. The USB-cable is more easy: There is an internal free USB-Port on the controller... If everythink works as intended, I will maybe build my ERCF. This is the main reason for me to change to a revo. Putting a standard flow revo inside instead of a high flow, you can get quite a nice fillament tip on unload. Like on the mk3s with revo or the mk4. At least with well dryed PLA and ABS (PetG always is a bit stringy). Imho the best way to get a filamentchanger without cut&poo and all the waste. I realy hope someone finds a way to connect Anycubics new ACE pro to klipper...
Congrats and big thank you for the detailed tips! 1. Cool tip! I might do this. Yes the Q1 Pro comes with 32GB, 12x more free space! 2. Must-do-upgrade. Why Sovol keeps using these loud fans? 3. I never understood the commotion about switching out the hotend / extruder. I am very happy with the stock extruder. Now that I am comparing with the Q1 Pro I see how spoiled we are with the amazing Sovol extruders. 4. That is something I should do. The stock probe is garbage and a big limitting factor. 5. I am testing a BTT K-Touch (video soon) and my Sovol screen is on its way. Great tips for connectivity! 6. Yes, ERCF is on my radar as well. I am eager to get into multi-material. Thanks again for sharing your insights-your upgrades, experiences and enthusiasm really add value to the community!
@@gerGoPrint3D 2) The fan Sovol uses is about 1€. A Noctua is about 15€. Not everyone needs a quite fan, so it's OK. 2) The hotend the SV08 uses is quite new. So quite hard at the moment to get different nozzles. So I definitly understand if someone changes the hotend/nozzle. Also if you already have other printers with a lot of different nozzles/hotends, it might be a good idea to change the new printer to the same system. I already have a bunch of printers with Revo and also standard flow, high flow and ObXidian nozzles in multiple diameters. So instead of buying different nozzles/hotends for the SV08 (when available) it is much better to convert the SV08 to a Revo. Same for Bambulab X1C/P1S/P1P users: If you already have a set of different hottends (different diameters, bras and hardened steel) it makes sense to print a simple adapter and make adapter cables to use them in the SV08, instead buying a whole new bunch of hotends with different nozzles for the SV08 only. For changing extruders: While the extruder the SV08 uses is good in most cases, the distance between the gears and the hotend is a bit higher than on other designs. If you want to print softer TPU, changing to an revo roto extruder can help. Also of course if you want to build a toolchanger, you might want to use a tool that is already designed instead modifying the existing one. Also of course modding can be a hobby of its own. I have seen someone using Prusas Nextruder on a Voron 2.4, using his own code to make use of the loadcell. Quite fascinating ;-) Bur you are right; in most szenarios there is no real need to change the complete extruder. But it can be fun... For changing th
How is the Z offset and the build plate heating? I heard the build plate can get "bumps" from uneven heat. Thanks for the video, I am very interested in the 08.
The Z-offset issue in preproduction units were caused by inaccurate inductive probes which were too sensitive to temperature changes. Initial tests here show improvements. I haven't experienced any bed adhesion issues, so far, but I don't have the equipment to create a proper heat map of the printbed. I'll do my best to provide some measurements for the next video.
Want one even more after watching this video can i get the link to the video for the install of the upgraded fan im going to want to install those upon initial assembly for I too will not want the noise I use noctua fans on all my printers.Thank ypu again for the real time real life adventure of assembling a new printer!!
Yes, you can either use a more expensive / higher quality replacement blower, or just cut a bigger hole and put in a dirt cheap 80mm fan like I did... My fan upgrade actually costed nothing, because I simply use an old CPU cooler and run it at about 50% of its max speed, so it is almost compeletely quiet, but because of its size moves plenty enough air. Cutting a big hole was a bit of a challenge though...
It was arranged with Sovol earlier than the release day, but I am told this is a production unit and afaik it is already coming from the EU warehouse. But don't quote me on this. EU units are said to start shipping early June, except for a handful of them (this was discussed in one of their recent live streams)
54cm, but you'll also need min 5cm on the left side for the power plug which sticks out on the side of the machine. So overall you need 5cm on the left and about 16cm on the right (including a std 1kg spool on the holder)
Great video. Liked and subscribed. One question, did you order the side panels and HDMI screen when you ordered the printer or are they something you plan to order in the future? I'm curious because I ordered the side panels and touch screen with the printer, then I saw they each had their own release dates. So I'm wondering are they going to wait until everything is released and ship together or are they sending it out as they release? I'm hoping they ship as released so I can get my hands on the printer sooner. Love the built in bookshelf, great opportunity for a secret door there, lol.
You won't need to wait extra if you ordered with accessories! I too am getting side panels and the official HDMI screen. But the printer was sent ahead of these. Afaik everybody will get their printer first and the accessories later. They are also sending a kit of nozzles to test (0.2mm - 0.8mm). I will make videos of them all!
288 / 5 000 Hi Gergő! I also received the SV08, but the package is missing the PTFE tube and the quick connector! Could you tell me how long the PTFE tube is? Your video was helpful because I saw that the small tool box had the pipe. Also, the Z belt was noisy for me too, but I cleaned it :) Visszajelzés küldése
I am sure Sovol will send you the missing components. The PTFE tube is 73cm long in total, it's made up of a longer 60cm piece and a shorter 12cm piece and we have a connector between them (I think you can see that in my videos). Outer diameter 4.2mm and wall width 0.8mm gives an inner diameter of 2.6mm. I had the feeling mine was not the only machine with rattling Z pulleys :) I think they rushed these first batches too much, not waiting for the loctite to properly dry before assembly.
Not out of the box. The SV06 uses the old, low flow rate MK8 standard. All their newer printers use high flow nozzles, which can print much faster and handle special filaments better. With the T300 and SV08 they upgraded their high flow nozzle to an even newer, better standard which looks and works similar to the nozzles Bambu Lab printers use. They are not compatible, but look similar with an integrated heat block. You can get the new nozzle for the SV08 in various sizes from 0.2mm to 0.8mm in a kit. It is sold at reasonable prices (see links in the description of this video). Having said this, there are already community mods available to enable the extruder to work with many different nozzle standards. Check out Nadir's video where he talkes about this.
I received my SV08 yesterday. I found one of the heatsinks floating the the box. I found it came from the Y axis motor driver. The compound they used was very dry and would not hold it on. Any suggestion's? What do you use for heatsink compound? Thanks
It must have had a rough trip. The trouble with the main board that it is up-side-down, so you really need thermal adhesive (double sided thermal tape) to hold those heatsinks, not just paste.
@@gerGoPrint3D I agree but this a thick paste that has hardened I could make it stick. I am very concerned about the others dropping off while printing and damaging the drives. What did they use on yours? Thanks
@@jamescullins2709 It is the same kind of paste here, they seem to be holding well. But be sure to contact Sovol about the issue, if nothing else, have paper trail of the problem in case actual damage would happen.They might even be able to send you the correct adhesive or advise regarding cooling.
hi, thank you for the video? how did you get the final version right now? the normal delivery to europe will be early june... i think you are also from europe =)
Yes I am in Europe (Hungary). This printer was arranged with Sovol earlier than the release day, but I am told this is a production unit and afaik it is already coming from the EU warehouse. But please don't quote me on this. EU units are said to start shipping early June, except for a handful of them (this was discussed in one of their recent live streams)
@@gerGoPrint3D thank you for your reply and the info =) i cant wait for mine, i am super hyped xD please do more videos about the sv08 best greetings from a quater hungarian outa germany =)
You are probably right. But upon talking with beta testers it is way closer to production than the review units sent much earlier to bigger YT channels. However based on experience with earlier models, HW is not likely to change, they only tweak software and documentation at this point...
Love this. Du bist sehr deutsch. Great work, thanks for taking the time to go through it carefully and bring us along.
Ah what a treat! Another sv08 video to wake up to! Thank you!
definitely saved for future build reference guide!!
Yes, I’ve included the User Manual page numbers in the chapters for reference. Thanks to Sovol’s clear presentation, the assembly wasn’t much of a challenge, but my video could hopefully save a few minutes for the new SV08 owner community.
ooo im jealous cant wait to get mine!
I have to say your videos are very informative and the extensions for the sovol sv06 and SV07 as well as for the T300 are simply great .Would love to see some of your print profiles for the Sovol series .With best regards, Jean from Belgium
Great video, thanks!
Ohhh looking forward to this
thank you sir!
I haven't ordered one yet, but I'm seriously considering it.
Definitely need to quiet that fan down.
That's an easy upgrade. With the exception of my SV07+ I've replaced the board cooling fans in all my printers for quieter ones. SV07+ comes with temperature controlled fans, which is a game changer. The SV07/Plus is such an underestimated device. But I have to say, this idle mode fan noise is the only negative I can say about the SV08. Sovol team really did their best here!
nice assembly vid!! you're funny; lemme ground myself then walk back to the unit!! haha at least ya have the sense to do it!! thank you for taking the time! to make this video!!!
Yes, it was more like a reminder to watch out for this
@@gerGoPrint3D Nice!!
I got mine a few days ago. Already did some changes (they are not nessasary, but nice2have):
1. The original eMMC is just 8GB, wich limits the number of space for gcode and timelapses. As as the lazy guy I am, I never clear up anyway. So I copyed the firmware to an 32GB (from Qidi...). The filesystem expands automaticly. So just make a backup of original eMMC and write it to the new one. Cost about 24€.
2. The controllerboard fan was replaced by an Noctua 24V 4010.
3. I ordered the Revo coldend the next Layer had designed for the SV08. However, I can not recommend this. The tollerances are not perfect, I had to postprocess a bit. This went wrong. The coldend is now not perfectly perpendicular to the bed - and the nozzle (the heatbreack part) bended. Destroyed 2 Revo nozzles (they still work, but definitly not usable in other hotends anymore). However, on printables is a design for an Adapter to use Bambulab X1C/P1P/P1S coldends on the SV08. So I now ordered the Biqu Panda Revo for the P1S to try it with this adapter.
4. Just got the Biqu microprobe. Will try it next weekend. But actually the Revo nozzles are so precise manfactured, I do not think I have to recalibrate z-offset often anyway.
5. The BTT 5 inch HDMI Touchscreen works quite well. With 38€ quite affordable. However, I also ordered an 11€ HDMI foil-cable to route HDMI invisible from the ouside port back into the printer and internaly to the display. The USB-cable is more easy: There is an internal free USB-Port on the controller...
If everythink works as intended, I will maybe build my ERCF. This is the main reason for me to change to a revo. Putting a standard flow revo inside instead of a high flow, you can get quite a nice fillament tip on unload. Like on the mk3s with revo or the mk4. At least with well dryed PLA and ABS (PetG always is a bit stringy). Imho the best way to get a filamentchanger without cut&poo and all the waste. I realy hope someone finds a way to connect Anycubics new ACE pro to klipper...
Congrats and big thank you for the detailed tips!
1. Cool tip! I might do this. Yes the Q1 Pro comes with 32GB, 12x more free space!
2. Must-do-upgrade. Why Sovol keeps using these loud fans?
3. I never understood the commotion about switching out the hotend / extruder. I am very happy with the stock extruder. Now that I am comparing with the Q1 Pro I see how spoiled we are with the amazing Sovol extruders.
4. That is something I should do. The stock probe is garbage and a big limitting factor.
5. I am testing a BTT K-Touch (video soon) and my Sovol screen is on its way. Great tips for connectivity!
6. Yes, ERCF is on my radar as well. I am eager to get into multi-material.
Thanks again for sharing your insights-your upgrades, experiences and enthusiasm really add value to the community!
@@gerGoPrint3D 2) The fan Sovol uses is about 1€. A Noctua is about 15€. Not everyone needs a quite fan, so it's OK.
2) The hotend the SV08 uses is quite new. So quite hard at the moment to get different nozzles. So I definitly understand if someone changes the hotend/nozzle. Also if you already have other printers with a lot of different nozzles/hotends, it might be a good idea to change the new printer to the same system. I already have a bunch of printers with Revo and also standard flow, high flow and ObXidian nozzles in multiple diameters. So instead of buying different nozzles/hotends for the SV08 (when available) it is much better to convert the SV08 to a Revo. Same for Bambulab X1C/P1S/P1P users: If you already have a set of different hottends (different diameters, bras and hardened steel) it makes sense to print a simple adapter and make adapter cables to use them in the SV08, instead buying a whole new bunch of hotends with different nozzles for the SV08 only.
For changing extruders: While the extruder the SV08 uses is good in most cases, the distance between the gears and the hotend is a bit higher than on other designs. If you want to print softer TPU, changing to an revo roto extruder can help. Also of course if you want to build a toolchanger, you might want to use a tool that is already designed instead modifying the existing one.
Also of course modding can be a hobby of its own. I have seen someone using Prusas Nextruder on a Voron 2.4, using his own code to make use of the loadcell. Quite fascinating ;-)
Bur you are right; in most szenarios there is no real need to change the complete extruder. But it can be fun...
For changing th
How is the Z offset and the build plate heating? I heard the build plate can get "bumps" from uneven heat. Thanks for the video, I am very interested in the 08.
The Z-offset issue in preproduction units were caused by inaccurate inductive probes which were too sensitive to temperature changes. Initial tests here show improvements. I haven't experienced any bed adhesion issues, so far, but I don't have the equipment to create a proper heat map of the printbed. I'll do my best to provide some measurements for the next video.
Thanks for the video.
What are the dimensions of the controller board fan?
Might as well source a quiter alternative while waiting for the printer.
Also, any idea what voltage it is?
They are using a 4010 24V
@@gerGoPrint3D many thanks. Greatly appreciated 👏
Want one even more after watching this video can i get the link to the video for the install of the upgraded fan im going to want to install those upon initial assembly for I too will not want the noise I use noctua fans on all my printers.Thank ypu again for the real time real life adventure of assembling a new printer!!
Yes, you can either use a more expensive / higher quality replacement blower, or just cut a bigger hole and put in a dirt cheap 80mm fan like I did... My fan upgrade actually costed nothing, because I simply use an old CPU cooler and run it at about 50% of its max speed, so it is almost compeletely quiet, but because of its size moves plenty enough air. Cutting a big hole was a bit of a challenge though...
THANK YOU, for the quick replay as always.What are your plans for upgrades for the sovol SV08 @gerGoPrint3D
I'm really excited to get mine, ordered at launch, I'm like 6 weeks away though 😢
Yes, it’s worth the wait. :) On the bright side, by the time you receive it, all the initial problems should be sorted out!
So does this mean that the printers are being shipped out finally?
It was arranged with Sovol earlier than the release day, but I am told this is a production unit and afaik it is already coming from the EU warehouse. But don't quote me on this. EU units are said to start shipping early June, except for a handful of them (this was discussed in one of their recent live streams)
How wide is the machine with out the spool holder?
54cm, but you'll also need min 5cm on the left side for the power plug which sticks out on the side of the machine. So overall you need 5cm on the left and about 16cm on the right (including a std 1kg spool on the holder)
Thanks for the reply was checking to make sure it would fit in my server rack with my others
@@drnorris1985 I thought so ;) I hope it fits!
Great video. Liked and subscribed. One question, did you order the side panels and HDMI screen when you ordered the printer or are they something you plan to order in the future? I'm curious because I ordered the side panels and touch screen with the printer, then I saw they each had their own release dates. So I'm wondering are they going to wait until everything is released and ship together or are they sending it out as they release? I'm hoping they ship as released so I can get my hands on the printer sooner. Love the built in bookshelf, great opportunity for a secret door there, lol.
You won't need to wait extra if you ordered with accessories! I too am getting side panels and the official HDMI screen. But the printer was sent ahead of these. Afaik everybody will get their printer first and the accessories later. They are also sending a kit of nozzles to test (0.2mm - 0.8mm). I will make videos of them all!
@@gerGoPrint3D Great news, thank you for taking the time to reply.
288 / 5 000
Hi Gergő! I also received the SV08, but the package is missing the PTFE tube and the quick connector! Could you tell me how long the PTFE tube is?
Your video was helpful because I saw that the small tool box had the pipe. Also, the Z belt was noisy for me too, but I cleaned it :)
Visszajelzés küldése
I am sure Sovol will send you the missing components. The PTFE tube is 73cm long in total, it's made up of a longer 60cm piece and a shorter 12cm piece and we have a connector between them (I think you can see that in my videos). Outer diameter 4.2mm and wall width 0.8mm gives an inner diameter of 2.6mm. I had the feeling mine was not the only machine with rattling Z pulleys :) I think they rushed these first batches too much, not waiting for the loctite to properly dry before assembly.
can i convert to rapido UHF for this printer?
Check Nabir's video he's already designing print head upgrades to fit various nozzle styles
will the sovol mk8 nozzles work on the sv08?
Not out of the box. The SV06 uses the old, low flow rate MK8 standard. All their newer printers use high flow nozzles, which can print much faster and handle special filaments better. With the T300 and SV08 they upgraded their high flow nozzle to an even newer, better standard which looks and works similar to the nozzles Bambu Lab printers use. They are not compatible, but look similar with an integrated heat block.
You can get the new nozzle for the SV08 in various sizes from 0.2mm to 0.8mm in a kit. It is sold at reasonable prices (see links in the description of this video).
Having said this, there are already community mods available to enable the extruder to work with many different nozzle standards. Check out Nadir's video where he talkes about this.
I received my SV08 yesterday. I found one of the heatsinks floating the the box. I found it came from the Y axis motor driver. The compound they used was very dry and would not hold it on. Any suggestion's? What do you use for heatsink compound? Thanks
It must have had a rough trip. The trouble with the main board that it is up-side-down, so you really need thermal adhesive (double sided thermal tape) to hold those heatsinks, not just paste.
@@gerGoPrint3D I agree but this a thick paste that has hardened I could make it stick. I am very concerned about the others dropping off while printing and damaging the drives. What did they use on yours? Thanks
@@jamescullins2709 It is the same kind of paste here, they seem to be holding well. But be sure to contact Sovol about the issue, if nothing else, have paper trail of the problem in case actual damage would happen.They might even be able to send you the correct adhesive or advise regarding cooling.
@@gerGoPrint3D Good advice. I have already emailed and messaged them about it but no reply yet. thanks
hi, thank you for the video? how did you get the final version right now? the normal delivery to europe will be early june... i think you are also from europe =)
Yes I am in Europe (Hungary). This printer was arranged with Sovol earlier than the release day, but I am told this is a production unit and afaik it is already coming from the EU warehouse. But please don't quote me on this. EU units are said to start shipping early June, except for a handful of them (this was discussed in one of their recent live streams)
@@gerGoPrint3D thank you for your reply and the info =)
i cant wait for mine, i am super hyped xD
please do more videos about the sv08
best greetings from a quater hungarian outa germany =)
@@onkelwernerswerkstatt Das werde ich auf jeden Fall! Und ich antworte Ihnen auf drei Viertel Német és egy negyed magyarul!
@@gerGoPrint3D Super vielen Dank =)
I don't think I'd fully trust Sovol that this is actually a production unit.
You are probably right. But upon talking with beta testers it is way closer to production than the review units sent much earlier to bigger YT channels. However based on experience with earlier models, HW is not likely to change, they only tweak software and documentation at this point...