Use a peltier in parallel with a 5v fan and add a aluminium thin sheet to the cold side of the peltier device to increase the cooling area. It works very well even on hot days. While playing Black Desert mobile on my Xiomi Mi 8 the battery reached temperature above 42 °C. With this set up it stays between 28 °C and 33 °C, depending on ambient temperature. Without the peltier device the heat can't do almost any difference if the day is too hot.
Planning on doing this with (Fan) Fan Size: 40×40×10mm Connector: 3pin Voltage: DC 12V Rated Current: 0.087Amp ±10% Bearing: Sleeve Bearing Fan Speed: 5500 RPM±10% Noise Level: 16-25dBA Air Flow: 10-28CFM Life: 35000 hours (Peltier) Rated Voltage: 5V DC Max. Current: 5A Max. Temperature Difference: 67 deg C Max. Voltage: 6.2V Max. Refrigerating Power: 19.4W Couples: 49 Size (L x W): Approx. 1 x 1inch / 25 x 25 mm Then connect both to 12v 1.5a adapter via usb, I will put thermal pad between the phone and peltier, will it work without condensation?
@@franciscoayon9470 unfortunately, found prebuild cooler. And there's condensation when being use. Since then I stop using any active cooler. Only playing game infront fan.
I made one using the parts from a mini soda cooler. Runs on 12 volts and has a much larger heat sink and fan. Playing cod mobile on low graphics overhead my phone after 20 minutes. Now I play on high graphics no problem my phone is ice cold.
Orang indo bro? rekomendasi pake komponen kek gini karena itu komponen nya ngipas panas terus ngeluarin di depan kipas nya jadi gak langsung kipasnya ngedingin hp biar ngehindar dari ngembun kata orang orang
condensation comes from water in the air that forms moisture, your phone is almost air tight so there's zero chance of condensation occuring inside the phone
Do not do this if your phone doesn’t have water resistance. If the temperature drops below ambient, water will condense inside the phone and damage your device.
Bruh do you even know how much power your power bank can produce? And how much voltage does it produces...and how much does the peltier need to work efficiently
use usb cable which has black and red wire bcoz red is positive and black is negative dont use this color coding cable(red wire is + and black wire is -) u have to connect both red wire of peltier and fan in red and other blacks in blacks
Why do u have iphone for 1 300 $? You can buy Asus Rog Phone 5 with Snapdragon 888 for 1 100 $ and this is most powerful phone is the universe. P.S: and this phone has its cool cooler
It works even better if the output is 12v 5 ampere power supply with AIO radiator. In theory you even make an AC. Radiator temps with fan temperature maintained 30°C in hot side , u can get 0° in cold site. Try it thanks later..
yes. For better result use a 5v fan in parallel with the peltier module. You can use a 5v-2A charger or a 12V-2A charger. Increasing the voltage of the charger will make even lower temperatures
@@sigitbudi6755 With a 12v fan you will need 2 chargers. I tried 12V fan in parallel with the Peltier module using a 12V-2A charger. The fan is too slow and wasn't enough to cooldown the the heatsink. Maybe be it will work if you find a high rps 12V fan
@@sigitbudi6755 Even with 12V adapter the peltier will get almost all the current and the fan will run very slow. At least mine did. Is way better with 5v fan in parallel with a peltier device with a 5V-2A adapter
Use a peltier in parallel with a 5v fan and add a aluminium thin sheet to the cold side of the peltier device to increase the cooling area. It works very well even on hot days. While playing Black Desert mobile on my Xiomi Mi 8 the battery reached temperature above 42 °C. With this set up it stays between 28 °C and 33 °C, depending on ambient temperature.
Without the peltier device the heat can't do almost any difference if the day is too hot.
Planning on doing this with
(Fan)
Fan Size: 40×40×10mm
Connector: 3pin
Voltage: DC 12V
Rated Current: 0.087Amp ±10%
Bearing: Sleeve Bearing
Fan Speed: 5500 RPM±10%
Noise Level: 16-25dBA
Air Flow: 10-28CFM
Life: 35000 hours
(Peltier)
Rated Voltage: 5V DC Max.
Current: 5A Max.
Temperature Difference: 67 deg C Max.
Voltage: 6.2V Max.
Refrigerating Power: 19.4W
Couples: 49
Size (L x W): Approx.
1 x 1inch / 25 x 25 mm
Then connect both to 12v 1.5a adapter via usb, I will put thermal pad between the phone and peltier, will it work without condensation?
can you make a video on this please...
@@TheKiD013 so how did that go?
@@franciscoayon9470 unfortunately, found prebuild cooler. And there's condensation when being use. Since then I stop using any active cooler. Only playing game infront fan.
I made one using the parts from a mini soda cooler. Runs on 12 volts and has a much larger heat sink and fan. Playing cod mobile on low graphics overhead my phone after 20 minutes. Now I play on high graphics no problem my phone is ice cold.
From where u brought all parts?
Too low temp can also harm ur device
@@sheralizaidi6440 search: 40X40 HEATSINK & 40X40 FAN and PELTIER Module
How do you run on 12v? What power supply do you use??
@@shrinivas7068 Only if you're reaching near freezing temperatures.
Easy and best way to make this cooler🥶🥶 you are amazing bro
your the best bro mene apke bouth sare vedio dekhe hai aur apke chanel ko subscribe be kar diya hai aur har vedio par like be karta hu
Back after 8 months...
Bro I subscribed you when your channel have 1k something subs
Give me a heart bro
that pvc holder... i really love the idea..
Hi, I am an Iranian and I used a monopod clamp and recharged the product
What is the material used to make the heat sink? Is it aluminum?
Yes
Bro danger not, without additional components?
please reply bro.
Orang indo bro? rekomendasi pake komponen kek gini karena itu komponen nya ngipas panas terus ngeluarin di depan kipas nya jadi gak langsung kipasnya ngedingin hp biar ngehindar dari ngembun kata orang orang
good one..
Will this keep your phone cool? Any positive results?
Yes it works I have tried ti
@@ムケシュ Brother,, do the dc fan inserted here really cools the peltier's hotter side... Is that worth??
And also bro,, For the current supply for the peltier I have 30W adapter ( phone's charger).. so will that work, or will it damage the peltier ??
Brother what is the price of peltier plz tell me
which peltier module you are using
How many degree celcius can it reduce while gaming than usual ?
Around 3°c while gaming .
what the fuq
Avinash naredla wtf you can mining with your phone lmao
Can give me link for this all products...I wanna buy
exactly what i wanted
1 more experiment how about adding an pc processor cooler aio from deepcool or nzxt etc
But peltier will absorbed full voltage !
What is the price of SP1848-27145
palties? Plz replay
Hi, What if the condensation forms inside the cell phone?
Use low rating peltier for minimum condensation.
your phone will get some moisture??
@@lloydiedesu5131 that's inevitable
A little bit of moisture if you use the setup that i explained on another comment here.
condensation comes from water in the air that forms moisture, your phone is almost air tight so there's zero chance of condensation occuring inside the phone
bro i have a doubt, By using peltier, moist may appear inside the phone.. so it can make serious problems
If you turn it off then there will be moist..
Using a 12v peltier on 5v won't cool that much...
So, there should be no moisture
@@PYR069. what do you mean by turn it off? We need to keep it turn on?
@@kizo_xwhen you use it'll get cold.. and after using it (turning it off) the surface will start condensing.
Yrah right! A 12v 6amp peltier is being powered by a 5v power bank makes sense 😆
Peltier's work with voltages between 5 to 16V
Woah my guru is back🥳
Inggris campur indo┗(•ˇ_ˇ•)―→
@@misiskygaming6262 wkwkwkwkkw emang nih Chanel orang indo apa😂
tell me peltiar model...?
why didnt you show how effective it was
Do not do this if your phone doesn’t have water resistance. If the temperature drops below ambient, water will condense inside the phone and damage your device.
It wont cool that much...
Its a 12v peltier and he is using 5v
Right, but even if phone have water resistance, it will not help in case of condensation =)
Iphone is heating ?
Bhai ya batri kider sy mly gi
heat sink size?
Keep It Bro So Cool Idea 💡
Bro could I please give me the link to buy the. Same heatsink u have used bro....pls rply
Bro on what voltages u are operating this peltier module(Sp1848 Da 27145)
Nice work.😍😍
Bruh do you even know how much power your power bank can produce? And how much voltage does it produces...and how much does the peltier need to work efficiently
What USB cable you used? Mine has 4 colored wires (green blue gold and red) dont know what to do!?
Rastgele bağla yapram
use usb cable which has black and red wire bcoz red is positive and black is negative dont use this color
coding cable(red wire is + and black wire is -) u have to connect both red wire of peltier and fan in red and other blacks in blacks
What is the height of the heatsink?
do you measure the temperature before and after? I wanted to know how much effectiveness
Helloo, what is the size of the materials ? Can u give me each?
SUBSCRIBED
40mm
Why do u have iphone for 1 300 $? You can buy Asus Rog Phone 5 with Snapdragon 888 for
1 100 $ and this is most powerful phone is the universe.
P.S: and this phone has its cool cooler
What kind of plastic is that on ur cooler?
When every imagination is already a video in RUclips. Fml
Is the fan blowing away from the phone, or is the fans air going to the phone
Looks like it's blowing into the heatsink (towards the phone).
As Cappy said, probably into the phone.
Lol it's on heat sink 😂 it's works same as PC cooling fans.its throw air out side to reduce the heat from heat sink.
Product link please....
It works even better if the output is 12v 5 ampere power supply with AIO radiator. In theory you even make an AC. Radiator temps with fan temperature maintained 30°C in hot side , u can get 0° in cold site. Try it thanks later..
Thats work????
yes. I tested it. See my comment
Great 👍👍👍 ..iam try to this. Gaget..✌️✌️
So cute omg like a mini CPU fan >.
Yaa but this is not pink😅
fan link?
without module step up ??
does it not condense?
U need the heatsink that actually touches the components.no real use to cool down the case 😀
Bro I want but this all component ,plz.give link
Is it safe
U need tharmal paste
Bro please give me all products link
Does that power bank supplies enough power to the Peltier module to work efficiently?
I use three stacks of teg type modules with 4010 12v dc cooling fan
I made benchmarks, one teg module is not enough to draw out heat from the phone
Simple... but perfect
is that a 5V fan ?
yes. For better result use a 5v fan in parallel with the peltier module. You can use a 5v-2A charger or a 12V-2A charger. Increasing the voltage of the charger will make even lower temperatures
How if i use 12v ? It's cheaper
@@sigitbudi6755 With a 12v fan you will need 2 chargers. I tried 12V fan in parallel with the Peltier module using a 12V-2A charger. The fan is too slow and wasn't enough to cooldown the the heatsink. Maybe be it will work if you find a high rps 12V fan
@@zehthales2595 how about using 12v dc adaptor??
@@sigitbudi6755 Even with 12V adapter the peltier will get almost all the current and the fan will run very slow. At least mine did. Is way better with 5v fan in parallel with a peltier device with a 5V-2A adapter
Why you are making a phone cooler for iphone😂😂
Wow. Maybe the phone needs cooler for gaming ?I don't know (ridiculous)😂😂
@@Carnage101 he's making because he is doing their job🤘
It work for any device like samsung
itu pake brp volt dan brp amper
Cool as cool of ur work man... 🙏😋🙏
Bro metereal name please..
Heatsink and Fan purchase link
Bro u make awesome
will the peltier work on 5v power bank?
I hv the same doubt...
There are Peltier that works with 5Volts instead 12v they are more smaller but works
@@kizo_x which air?
@@kizo_x air should be blown on heatsink coz peltier heat up as hell..
kis kis ko bokin diy ka idea acha laga please like
peltier module runs in 12v,any usb is 5v..is it good?
same question
I hv the same doubt..
Same question broo
I thinkk fack videos
Nama, jenis, dan ukuran kipas nya berapa ya boss?
but the will goes to minus
Not work 12v 6 amp peltier modul dc 5v
Power banks
U tried ?
ഓവർ ഹീറ്റ് bro
Nice
Bro you are playing on iPhone 11 fuck is it overheated
Thank you bro
Сомневаюсь в том что он охлаждает
Nice yaar
Near about 1000 Rs. Cost
New subscriber size of heat sink please
40mm
How to bye
OP bro
Hi
Bro meteral ka buy link do please
Conseguiu medir a temperatura antes e depois?
Sala sidhe cpu mein hi Peltier lagado
what a nonsense 😂
why anyone need cooler if they has a leatest iphone .
He use coolr in iphone why you need coolr in iphone 😂😂😂🤣🤣
The Deadly Sins dude iphone 5s heats up like your holding a hot tea cup
Pls response
#blackshark😅
Why dont you keep the phone in freeze
Just a joke bro
It could work but definitely notrecommend xD
i did actually put my phone in freezer by accident and i was searching for it 1 hr for it and it was frozen i sayed : what the fuq