ALTERNATOR Replacement Fast and Very Easy Toyota Sienna

Поделиться
HTML-код
  • Опубликовано: 1 дек 2024

Комментарии • 35

  • @bullydungeon9631
    @bullydungeon9631 11 месяцев назад +2

    Dude you rule you just made one part of my life way easier

    • @TheEtixzShow
      @TheEtixzShow  10 месяцев назад

      Thanks For Positive feed back!! Glad to have helped you!!!

  • @Brian-ri7rx
    @Brian-ri7rx 2 года назад +4

    You really saved me a lot of time and frustration. Great advice and heads up on the tricky parts. Only 15 minutes of rubrics - generator and 5 minutes of cussing, a personal best. Thank you!

    • @TheEtixzShow
      @TheEtixzShow  2 года назад

      Lol😂… no problem friend!! Hey but it worked instead of going the long way to removing the Alternator!!

  • @mrtjdodd
    @mrtjdodd Год назад +1

    Great job, thanks for sharing. Your method of getting that alternator out and back in is the best by far. Thanks again.

    • @TheEtixzShow
      @TheEtixzShow  Год назад

      I really Appreciate the positive feedback🔥💯🙏 i am also glad that you found my method helpful!! Happy Holidays!!!

  • @edwarddorville9973
    @edwarddorville9973 2 года назад +1

    I wanna say Big Thanks for this video. I used it to replace my 09 Sienna's Alternator, it made it an easier job than otherwise. Thanks 👍 and Blessings 🙌 🙏!

  • @jonathanlaw603
    @jonathanlaw603 7 месяцев назад +1

    Good video. Couldn't have done it without you.

    • @TheEtixzShow
      @TheEtixzShow  7 месяцев назад

      My pleasure friend!!! Glad it helped out!!!

  • @catarrhinegabriel
    @catarrhinegabriel Год назад +5

    This is the way, folks. It works, and it works well.
    A few additions to these excellent instructions:
    When you first loosen the alternator, point the pulley down in the space underneath the coolant pipe. This allows you to take the angle bracket off the back right-side bolt. Remove the bracket before trying to take the alternator out.
    The solution to the rubik's cube is to flip the alternator in place 180 degrees so the pulley is now facing the driver's side of the vehicle. Then remove it by allowing the coolant pipe to pass between the mounting flanges on the alternator. Get the new alternator in by doing these steps in reverse. Works like a charm.

  • @fernandoramos3677
    @fernandoramos3677 2 года назад +2

    Thanks for this tutorial is very helpful I will try to do it myself you make it look easy 👍

  • @bullydungeon9631
    @bullydungeon9631 11 месяцев назад +1

    Super inportant please read - the serpentine belt tensioner has an allan key slot for locking it in the loose position so you have two hands to put the belt on

    • @TheEtixzShow
      @TheEtixzShow  10 месяцев назад

      Highly appreciate it.. thanks!!!

  • @erroldillon1548
    @erroldillon1548 2 года назад +1

    Great video! I wish you had shot everything on video. Please shoot the video next time!!! Thanks

  • @Bamatime719
    @Bamatime719 4 месяца назад +1

    Clever as fuck! Thank you. Every one of your suggestions are great.

    • @TheEtixzShow
      @TheEtixzShow  3 месяца назад

      @@Bamatime719 thanks for the BLUNT feedback highly appreciated!!!

  • @timnickerson5389
    @timnickerson5389 4 месяца назад

    How did you reach the bottom bolt?

  • @OnlineAutoRepairVideos
    @OnlineAutoRepairVideos 2 года назад +1

    Great instructions

  • @eriksmith4774
    @eriksmith4774 4 месяца назад

    Why Not Remove that coolant pipe since you drained a bit?

  • @dannysautorepair
    @dannysautorepair Год назад +1

    Great video thanks

  • @JuanCruz-nu4mg
    @JuanCruz-nu4mg Год назад +1

    I did this today, hands down the worst alternator ive ever done, taking it out was a huge pain in the ass, luckily the new one dropped right in easy peasy

    • @TheEtixzShow
      @TheEtixzShow  Год назад +1

      Here to help!!! Please share, like and Subscribe!!! This really would help me out!!! 🙏

  • @Carl_theminivan
    @Carl_theminivan Год назад +1

    Everyone said to replace the negative one first.

    • @TheEtixzShow
      @TheEtixzShow  Год назад

      When disconnecting cables, 1st Neg then pos. When connecting cables, pos 1st and then Neg

  • @nandorodriguez3264
    @nandorodriguez3264 2 года назад +1

    Is this also same for 2010 ?

  • @michaelong655
    @michaelong655 11 месяцев назад +1

    Stop posting bullying clip, Tech of Toyota can not do like you , on post you do nothing only bla bla bla

    • @TheEtixzShow
      @TheEtixzShow  11 месяцев назад

      Happy Holidays to you🫵 and your Family🎄💯🙏🔥 Thank you. Please come back again.