Can you please make a full video from start to finish for CZ 457 MTR stock, Not sure where you will need to drill holes. I'm thinking using an 8" or 10" rail. Thanks
hello, nice tutorial. can you help me with a sabatti tactical evo stock? it has 2 pre drilled holes in the front of the forend. the inside of the stock is not flat the same as in the video. i wonder how i secure it without a t nut.
I really hope you still monitor this post or someone knows. I just purchased a T4A/GAP build 6.5 PRC. Original plan was for a full length ARCA, but they stated due to the contour it was not possible. We went with a shorter AREA 419 ARCA. After watching this, I really am hoping this rail is an option for me. Please respond if anyone knows if this option will work! Or if the Manners T4a contour is different now.
I had some problems with this. First, the Manners PRS TCS stock's line down the "center" was not in fact centered so I was a good bit off once the rail was threaded on and had to redo, my mistake I should have visually confirmed with the rail. Second and more disappointingly, is that tapping in the T-nuts bulged the bottom of my stock so the rail would not sit flush. I tapped it back in and am clamping it flat and filling the hole with epoxy. I drilled a third hole, clamped the rail in place and tapped in the T-nut with something on the other side protecting it from budging. I now have three holes instead of one to install the rail.
Getting ready to purchase a 14" ARCA lock rail for my CZ 457 Varmint MTR and one for my CZ 457 Varmint. I watched your other video on installing about an 1/8" forward of mag release on the MTR. How many t-nuts should I install for the best hold with minimal injury to the wood? Should I use the rear most hole?
Do you find that the prongs on the T nut bite well enough that not epoxy on the T nut is necessary? Not that under bolt clamp load it would move, but more, if I had to remove and install the arca plate? The more I type it out the less is seems needed
I’d like to know the length of that ARCA rail? I’ve got a custom barrelled action coming with a Manners T4A and I’d really like to instal a system like this but I’m no fan of the rail extending beyond the forend
Can you please make a full video from start to finish for CZ 457 MTR stock, Not sure where you will need to drill holes. I'm thinking using an 8" or 10" rail. Thanks
I really like the Camo patterns Manners use on these stocks. I wonder if I could get similar results using sponges and Krylon fusion.
Thank you so much for this video! It's an old video but still very valuable.
Bergara and savage have aluminum bedding chassis built in. How do you install on these?
hello, nice tutorial. can you help me with a sabatti tactical evo stock? it has 2 pre drilled holes in the front of the forend. the inside of the stock is not flat the same as in the video. i wonder how i secure it without a t nut.
I really hope you still monitor this post or someone knows. I just purchased a T4A/GAP build 6.5 PRC. Original plan was for a full length ARCA, but they stated due to the contour it was not possible. We went with a shorter AREA 419 ARCA. After watching this, I really am hoping this rail is an option for me. Please respond if anyone knows if this option will work! Or if the Manners T4a contour is different now.
I had some problems with this. First, the Manners PRS TCS stock's line down the "center" was not in fact centered so I was a good bit off once the rail was threaded on and had to redo, my mistake I should have visually confirmed with the rail.
Second and more disappointingly, is that tapping in the T-nuts bulged the bottom of my stock so the rail would not sit flush.
I tapped it back in and am clamping it flat and filling the hole with epoxy. I drilled a third hole, clamped the rail in place and tapped in the T-nut with something on the other side protecting it from budging.
I now have three holes instead of one to install the rail.
Thank you for posting this
Getting ready to purchase a 14" ARCA lock rail for my CZ 457 Varmint MTR and one for my CZ 457 Varmint. I watched your other video on installing about an 1/8" forward of mag release on the MTR. How many t-nuts should I install for the best hold with minimal injury to the wood? Should I use the rear most hole?
For your stock I would follow closely the instructions given in that other video. The two stocks are quite similar from a mounting perspective.
Thanks, you guys are awesome
Curious would this rail fit a McMillan a3-5 stock , not sure if it accepts the front action screw or not
Do you find that the prongs on the T nut bite well enough that not epoxy on the T nut is necessary? Not that under bolt clamp load it would move, but more, if I had to remove and install the arca plate? The more I type it out the less is seems needed
I’d like to know the length of that ARCA rail? I’ve got a custom barrelled action coming with a Manners T4A and I’d really like to instal a system like this but I’m no fan of the rail extending beyond the forend
This is a 14" ARCA rail you want a 12" if you dont want it to extend beyond the front.
Derek Rosenberg thanks for the reply mate