this was my thought. I do HVAC and ive come across many window units that had a small blown fuse on the board where the power comes in. So many people even experienced people miss those small fuses.
capacitors don't contain an acid, they contain a base, an alkaline base I think, and that's why vinegar is used to neutralize it. if it was an acid you would use a base to neutralize it, like baking soda. but even though it is a base, it will still eat away and destroy the components, just like if you were to leave the vinegar on there without cleaning it off (well, maybe not the vinegar that's used as food grade because it's diluted quite a bit.. but it would do SOME damage, but probably not as much as the caps do)- GOTTA LOVE SCIENCE!!!
Was goi g to make this same comment. It isn't a big issue, but if someone were to try to neutralize acidic things with Viniger they could be in for a very bad time
That's what I thought. I kept thinking that capacitors worked like batteries where they were alkaline. Especially saying he was using acid to neutralize "acid".
Have you tried using IPA to get stickers up? It's what I use. The lockpicking lawyer used it as well to lift a tamper proof sticker. Maybe it helps - good luck!
@tronicsfix thank you so much for your humour and light look on life. Your reaction to the reverse install of the big capacitator made me smile big time. keep doing content!
Just make sure you get rid of all the vinegar when you use it as a neutralizer since it will continue to corrode the board especially if it's underneath chips. Best to rinse the board with distilled water to displace it, then rinse with iso.
As someone that details things for a living, there’s only so much cleaning that can be accomplished with rinsing alone. A lil bit of gentle agitation with microfiber is the only way to be sure.
I had an OG Xbox with cold solder joints on the PSU wires that got to the main board. This was preventing the main board from getting any power from the PSU. I removed most of the old solder with solder wick and replaced it with some fresh solder and it solved the problem.
Can confirm. Cold solder joints can crystalize, much like if you move molten solder before it cools. The crystal lattice has voids. Those voids fill with oxygen from the air and oxidizes the metals in the solder from the inside out. After time, the resistance of the solder joint increases as more of the metal is oxidized, eventually becoming brittle and you have an invisible open-circuit.
I would test the traces near the battery clock under board to make sure there was no trace rot. Those traces affect the power😊. There are test points you can check. Might have to install a jumper wire or trace repair.
This! Those traces for the buttons are at the edge of the MOBO near the clock capacitor. Mine were corroded so bad I had to install the jumper wires and after I did, my Xbox works just fine again.
You are right. That clock capacitor might have ruined the power/eject button. Had a few of those broken ones fixed by adding a wire on the broken traces. Currently those xboxes found a way to the trash can because they failed again.
These were done with codes found on bottles of Mountain Dew. My mom would literally go to the market near my house and take the bottle caps off the returned Mountain Dew bottles. I had enough points to get one but they only allowed you to trade in the points at a certain time. I went to a summer camp for a week, during that time they released it and I missed my window. I am still so freaking upset I never got one of these.
i got a Mtn Dew hoodie, and an Optimus Prime Pepsi transformer. people from work would leave all their caps on my desk. i spent days entering in those codes!
The thing i love about OG xbox repair is how active the discord community is. I have repaired 100s of OGs since 09. Clock cap corrosion is usually the main culprit. The P/E continuity trace fix works almost always.
A common problem with these xboxes is damaged traces along the front of the board. Traces for the power led, on/off button and eject. There are points on the board you can solder jumper wires to, to resolve this issue ;) (Done this myself twice now, got both consoles working). Been working on a lot of old xboxes lateley ... You, Steve, and MyMateVince have been really educational and giving me the confidence to try and fix broken consoles and other devices, and been pretty succesful. Thanks!
You can also use 90-99% IPA, let it soak under the adhesive, and then carefully remove it. You can then re-apply it with new adhesive and it would look like the sticker was untampered with.
The issue with all adhesive removers, even IPA, is that is can bite into sticker clearcoats and make them foggy, or soak partially between the clearcoat at the graphics leaving a waterlogged look. There's really no way around it. Some stickers respond well, others do not. Life is a gamble. :) @@WantBadtime
Denatured alcohol is a good way to loosen the adhesive of stickers (even the security/warranty ones!) without damaging them. It even keeps the adhesive sticky once it evaporates.
Wii, Wii U, Nintendo DS, PlayStation 2 3 4, Xbox, Xbox 360, Xbox 360 slim, Xbox One, and Xbox One S have all been fixed by me because of watching your channel. I’ve had a lot of fun enjoying electronic repair. I purchased all this stuff cheap as not working on EBay. I got all my wireless controllers not working and fixed them as well. Thank you for your videos I’ve been enjoying my new hobby
Were you able to test the power supply after changing out the capacitors? Maybe use a known good power supply and test the rest of the board? It might help narrow down where your issue is...
this brings back memories lol. there is 4 places to check all of which are basically continuity checks, there is a fuse on the PSU while you are here check the cables and connectors, they are prone to broken solder joints, check the traces near the clock capacitor, the power board on here check the buttons, and the expansion cables/connectors.
@@indy5280 Yes that’s unfortunately true, and also many schematics can’t be attained without it being behind a pain wall, but I think a technician or engineer might have knowledge to recreate it
I bought my Mtn Dew edition Xbox about 8 years ago, also no power issue, just took a power supply out of a spare parts Xbox with same motherboard revision, works great to this day. Great video
I believe in you man. Let’s get it working. And yes you are inspiring me to go back and start workshopping old electronics which was something I did as a kid but not to this level before the internet
There are 4 traces on the underside of the motherboard, they run right along the front edge and then up the right side of the board. Those traces often get breaks from leaky capacitors. Those traces i believe are related to the power and eject buttons, so if they are damaged those buttons may not work at all.
I'm impressed that you removed the heatsyncs without being able to power on the console. Those are basically superglued to the dies until you apply heat.
Hello you should check the continuity between the front panel power and eject buttons and the PIC microcontroller on the motherboard. I fixed mine using a soldered wire between the 2. Absolutly worth a try 😊
As some have said, test the button continuity because the clock cap can cause issues there. Also, with a foxlink PSU the four solder joints for the power plug are worth taking a look at. The two outside joints are mount points its the inner two you want to re-flow solder to because they're notorious for bad solder joints.
This is so crazy you doing this video right now. You’ve been a big part of why I have gotten into the mod old console hobby recently. I’m actually in the middle of an og Xbox spruce up myself and actually got mine from the goodwill auction
That's why I stopped buying a lot of stuff, prices are too high. I started fixing all kinds of electronic things and vacuums 2010. Not as advanced as you do, you are top-notch.
Oh I use a straight edge box cutter to carefully remove labels. Heating them up works for most but those metallic ones just crumble no matter what you do. You did great with the tweezers too.
6:20 I was going to say "oooh, fancy!" about your vinegar bowl, but using a heavy crystal bowl for vinegar or IPA is a legitimately good idea. Something that heavy isn’t going to tip over if you brush it with your hand, and why buy new when you can repurpose old?
You will figure it out Steve Don't give up. Capacitors generally comprise a conducting salt based on long-chain aliphatic dicarboxylic acids and also a solvent, for example ethylene glycol. An example of a conducting salt used is dodecanedioic acid, which is generally used in the form of ammonium salts.
Im excited to see the 2nd video on this xbox repair. Its always interesting to see the process of working through the individual circuit board components too bring back old tech. Thanks TronixFix.
I'm not into computer repair but Xbox has always been my console of choice so this interested me. I'm going to subscribe just because I want to see you resolve the issues in part two!
So, they should resell something for significantly less than market value and so leave a larger margin for the next reseller? 🙄 FWIW, there are some great deals to be found at thrift shops -- just not in video games. I am an avid bibliophile, and I once purchased a vintage book about Princess Elizabeth (as she then was) for about $.50; the ABE online price was around $60. It is just not possible for _all_ products to be listed at market price; the key to success in collecting is finding those niches that are undervalued and exploiting them.
@@williamharris8367Goodwill specifically has all kinds of issues over wildly overpaying executives and turning local organizations into petty fiefdoms.
Their mission is charitable work, selling donations is how they raise money. The higher selling price allows them to do more charitable work. They don't set these prices, the market does. Be angry at the market instead.
Used to love watching these videos, also would get things off goodwill, now ever since this video when I go and look at games everything is wayyyy over priced used to be able to get things at good price, dont understand why you had to go blow it up just for some clout… glad it made you feel good though☺️☺️
Picked up a As is xbox one S from the pawn shop for $20. Hook it up and it kept throwing the error 102 , 106 codes. I knew it was a bad harddrive. Found my old laptopi n the closet that had a 1 terabyte harddrive . Formatted the harddrive , download xboxes firmware and the update. Now I have a working white xbox one s for nearly nothing. The ifixit guide helped me out . Thanks Ifixit
I love working on these old OG box's. You never know what the problem is going to be. I aquired three from a flooded basement. All corroded, rusty and nasty. Took me a while but I restored all of them.
Really enjoy your videos. I’ve been watching for a while now. Your videos have helped me troubleshoot and fix my stove circuit board, guitar amplifier, and a few elite controllers. Appreciate the videos
Great video! :D The only thing is that the folding animation around 7:30 to 7:40 ish actually made my heart drop. I thought u snapped the board in half 😭😨😱 Amazing videos though. I love tech.
I still have my OG Xbox back when i got it in 2008. Still running strong after a full recap, DVD drive swap, multiple HDD upgrades, and an HDMI mod. One of my favorite consoles.
The Mountain Dew Console is definitely one worth saving, and a favorite of mine. The color is just great. I certainly would of tested output power before reassembly. A fuse is the start point. But if there is no output power no reason to look at the board yet.
first thing to check is there voltage on the on switch ,if not check all the voltages from the psu ,if there is none (not all lines will be active in the off state)check any fuse on the psu ,if ok look for a high value resistor on psu (there may be two in series)they/it suply a start up voltage to the chopper chip .good luck with the repair
A few tips. Check for the fuse in the power supply, check that the front panel connector was plugged in, and as chris tursk mentions, check the front panel traces on the underside near the clock capacitor (segments 6 and 7 along the edge). Those will probably be PE#1 with the clock cap leaking. Strange though, usually I've seen it power on immediately when the console is plugged in in the wake of that damage, try the eject button as well to turn on the console (though that's also victim to the trace rot, along with the front panel LEDs and power trace).
It's easier using an Exacto Blade to get label corners up once you do you need to go slow and get heat under where you have it peeled up a actual heat gun almost to hot I feel a hair dryer works better. Nice find I hope you can get it going in the next video thanks!
I actually placed several bids on that Xbox to see how far it’s go. It all makes sense now knowing that highest bidder was willing to pay so much to just to have content material. I was the one who complained on Reddit about how people pay so much for these even for a dead nonfunctional unit
One good trick to know is that the vast majority of capacitors on a board are irrelevant. They can be removed and just kept as an open circuit as that is their effect in a DC circuit. Capacitors are used to smooth out the waveform of the voltage (which for DC is flat so no waveform). Also the bigger they are, the less useful they are (unless you are connecting the power supply to AC which needs big capacitors). There are some specific places where a capacitor is important, but those are rare.
Big ticket obvious and critical items Main Fuse and secondaries? PS output- Isolate problem there and if, use another. Clock circuit for corrosion as if that ant working, its a door stop! Visual check over board to see if you missed something when item is totally dead, work from PS forward through secondary caps or mosfets where board gets input power- This after you look for obvious damage on board.
I would have first checked voltage and current on the supply, fuse... If the supply is fine, I would go to the motherboard. good luck with this repair!
For older consoles like this, that you know people are highly unlikely to open up and replace the thermal paste, I would suggest using a carbon based thermal pad instead. It has the same qualities as thermal paste but has no requirements to be changed out once it dries up. It'll continue working forever, as long as the console still lives. I did the same thing with my Xbox 360 (OG Halo 3 Launch console) and it's been running for years without any problems. Mostly just pointing it out since most people wont think to replace thermal paste on older consoles.
Tip for removing labels/stickers is to put denatured alcohol in a syringe and after heating and getting 1 corner up a tiny bit, shoot the denatured alcohol behind it the label or sticker and lift slowly and it should come off really easily and then let it dry and all the adhesive will still be good after the alcohol evaporates
The PSU has a known fault of dry joints towards the 110v input. The boards also suffer with trace rot. There is a long trace at the front of the board for the pwr switch. The eject button will also turn on the console. The latter is worth checking but i would suspect the psu in this case.
I picked up a Mountain Dew Xbox a few years ago and it was a pretty good deal at around $300 US. It still appears to be absolutely immaculate condition and I've rarely seen another original Xbox that looks as nice. (I was a bit suspicious at first that it might have been a fake but everything with the case and internals has checked out as original.) Plus it already had a TSOP flash mod and an upgraded hard drive - which I upgraded again to 2 TB drive.
Acetic acid (vinegar) does not neutralize another acid. However, it does remove corrosion, but at the loss of more metal. Maybe you should find PH testing strips, distilled water (~7), and cotton swabs to know what's on the motherboard. Wet a swab, rub suspect area, and swipe along test strip.
Un-Du works great at removing adhesives and it dries almost instantly. I use it on everything and always have spare bottles available. Currently, 1 being used, 2 spares bottles and a 32 oz refill bottle. Just make sure to get either the yellow or white caps as the silver cap, California sales specifications, doesn't work.
Check the traces on the Clock compasitor. There are 3 traces that can get affected and they are used to power it on. Had a several of them to repair with that issue
Happy to see a video this New year! for the Stickers i use always a hair dry stet of a hot air because so you dont burn the plastic and also it looks like u have never open the console this trick is almost 15 years old, old school trick for keeping warranty! you can try it just ask your wife for her hairdry . srry my english not that good. God bless U from Germany
I use to work for an electronics manufacturing company, that made all sorts of stuff , and when we would clean the product's, they would use like an industrial dish washing machine, and after it was sent through, then you take out the product and let it air dry over night .
I'd recomment cleaning out the holes as well and use all new solder, instead of just heating up the old solder and pushing the new cap through. It'll not only remove any cap juice residue, it's also safer for plating at the through hole.
I have a regular XBOX with the same problem. One day it was working and the next it wouldn't even power up. Opened it up and found some bulging caps that I replaced, but still not working. It would power up for a split second before shutting down. I checked the power rails from the power supply and they were higher than they should be. Quite possibly there might be some over voltage protection on it shutting it down. Still haven't figured out what's wrong with it, so I wish you the best luck. Maybe I can get some pointers from the next video!
This was certainly a fun watch after replacing the capacitors on my cousin's childhood OG Xbox yesterday. First time doing it, and it was a success! I wonder what could be up with this one though. Possibly bad traces from the clock capacitor leak?
Awesome great content can't wait to see part 2 etc and thanks for showing us how to repair our electronics and fix it . happy belated Christmas and new years. I can't wait to see what you repair next etc
Isn’t it amazing that with the technology we have at our disposal nowadays the humble toothbrush is still the best tool for cleaning stubborn stains on a board.
Also I would highly recommend A mod chip. And not for piracy, but for being able to rebuild the hard drive and installing a new hard drive. Then you can reinstall the stock o s and still use the console without the security on the console
A bad fuse is the most likely suspect but check things like NON electrolytic capacitors as well if a fuse swap dose not get the job done. Also go over the entire board to look for any burned out components . The point of a fuse is to blow instead of the other components frying but something could of been blown by a good surge.
U can check the output of the power supply. It's same as a computer power supply. Just short the green wire with black ground wire. Check if psu is giving out voltage
I had an og Xbox and I heavily modded it. Added a usb port, bigger hd, replaced dvd drive with a LG, obv modchip, cleared out top Xbox logo and put a led light
My childhood xbox died and I wound up tossing it before I learned how easy it is to bring back to life. Now I go out of my way to make sure they have new caps and have been restored and not just refurbished
Fuse on the power supply is most likely gone. I'd check it in continuity mode. No beep = blown fuse. T2A 250V Fuse.
This is my guess, too.
Yep, I’m surprised he didn’t check any voltages across the power supply, but that does make for a 2nd video!!
yep, just had a 1.1 with no power, found the fuse on the PS was open.
this was my thought. I do HVAC and ive come across many window units that had a small blown fuse on the board where the power comes in. So many people even experienced people miss those small fuses.
Same here!
capacitors don't contain an acid, they contain a base, an alkaline base I think, and that's why vinegar is used to neutralize it. if it was an acid you would use a base to neutralize it, like baking soda. but even though it is a base, it will still eat away and destroy the components, just like if you were to leave the vinegar on there without cleaning it off (well, maybe not the vinegar that's used as food grade because it's diluted quite a bit.. but it would do SOME damage, but probably not as much as the caps do)- GOTTA LOVE SCIENCE!!!
Was goi g to make this same comment. It isn't a big issue, but if someone were to try to neutralize acidic things with Viniger they could be in for a very bad time
was just wondering how he would neutralise an acid with vinegar. Thanks for explaining
Is vinegar non-conductive?
That's what I thought. I kept thinking that capacitors worked like batteries where they were alkaline. Especially saying he was using acid to neutralize "acid".
Base= caustic. Acid= corrosive
Have you tried using IPA to get stickers up? It's what I use. The lockpicking lawyer used it as well to lift a tamper proof sticker. Maybe it helps - good luck!
@tronicsfix thank you so much for your humour and light look on life. Your reaction to the reverse install of the big capacitator made me smile big time. keep doing content!
I still can’t believe I installed it backwards! Thank you for the super thanks!
Just make sure you get rid of all the vinegar when you use it as a neutralizer since it will continue to corrode the board especially if it's underneath chips. Best to rinse the board with distilled water to displace it, then rinse with iso.
iso is good enough ...
As someone that details things for a living, there’s only so much cleaning that can be accomplished with rinsing alone. A lil bit of gentle agitation with microfiber is the only way to be sure.
I had an OG Xbox with cold solder joints on the PSU wires that got to the main board. This was preventing the main board from getting any power from the PSU. I removed most of the old solder with solder wick and replaced it with some fresh solder and it solved the problem.
Thanks for the comment. I'll make sure to check that
Can confirm. Cold solder joints can crystalize, much like if you move molten solder before it cools. The crystal lattice has voids. Those voids fill with oxygen from the air and oxidizes the metals in the solder from the inside out. After time, the resistance of the solder joint increases as more of the metal is oxidized, eventually becoming brittle and you have an invisible open-circuit.
good point
I would test the traces near the battery clock under board to make sure there was no trace rot. Those traces affect the power😊. There are test points you can check. Might have to install a jumper wire or trace repair.
This! Those traces for the buttons are at the edge of the MOBO near the clock capacitor. Mine were corroded so bad I had to install the jumper wires and after I did, my Xbox works just fine again.
You are right. That clock capacitor might have ruined the power/eject button. Had a few of those broken ones fixed by adding a wire on the broken traces. Currently those xboxes found a way to the trash can because they failed again.
Agreed. Check the traces for damage/rot
i think he knows.
Yeah, this is one of the first things I need to do.
These were done with codes found on bottles of Mountain Dew. My mom would literally go to the market near my house and take the bottle caps off the returned Mountain Dew bottles. I had enough points to get one but they only allowed you to trade in the points at a certain time. I went to a summer camp for a week, during that time they released it and I missed my window. I am still so freaking upset I never got one of these.
what a bummer
That would be upsetting! That sucks. I'm mad for you, lol
Sucks you never got one, but dang your mom sounds like a champ!
i got a Mtn Dew hoodie, and an Optimus Prime Pepsi transformer. people from work would leave all their caps on my desk. i spent days entering in those codes!
They really should have honored that i mean you had all those saved. Such a shame :/
Man, I appreciate that you still upload videos even if they’re not always a success.
not a success yet*
it's about the journey not the destination
The thing i love about OG xbox repair is how active the discord community is. I have repaired 100s of OGs since 09. Clock cap corrosion is usually the main culprit. The P/E continuity trace fix works almost always.
Tronicsfix, you should do a 2TB Sata upgrade for this bad boy. I believe it's a 1.3 revision so a TSOP mod would be best for it.
A common problem with these xboxes is damaged traces along the front of the board. Traces for the power led, on/off button and eject. There are points on the board you can solder jumper wires to, to resolve this issue ;) (Done this myself twice now, got both consoles working).
Been working on a lot of old xboxes lateley ... You, Steve, and MyMateVince have been really educational and giving me the confidence to try and fix broken consoles and other devices, and been pretty succesful. Thanks!
Also had this issue on a 1.4 xbox board, I agree it can be that kind of thing ;)
To remove stickers, try using the edge of one of anti static bags. Slide under the sticker and shimmy back and forth. Works well!
You can also use 90-99% IPA, let it soak under the adhesive, and then carefully remove it. You can then re-apply it with new adhesive and it would look like the sticker was untampered with.
@@WantBadtime I've never used beer for cleaning, awesome
WAIT LMAO@@fabiors10
Interesting. Seems like that could work well. Thanks for the tip
The issue with all adhesive removers, even IPA, is that is can bite into sticker clearcoats and make them foggy, or soak partially between the clearcoat at the graphics leaving a waterlogged look. There's really no way around it. Some stickers respond well, others do not. Life is a gamble. :) @@WantBadtime
I bought one of these around 5 years ago, it’s probably my favorite console I’ve owned. Looking forward to part 2, really hoping you can get it fixed!
So cool that you have one! I'm really hoping I can fix it too!
Denatured alcohol is a good way to loosen the adhesive of stickers (even the security/warranty ones!) without damaging them. It even keeps the adhesive sticky once it evaporates.
Correct. Get a syringe and a fine needle to work the alcohol under the label.
Wii, Wii U, Nintendo DS, PlayStation 2 3 4, Xbox, Xbox 360, Xbox 360 slim, Xbox One, and Xbox One S have all been fixed by me because of watching your channel. I’ve had a lot of fun enjoying electronic repair. I purchased all this stuff cheap as not working on EBay. I got all my wireless controllers not working and fixed them as well.
Thank you for your videos I’ve been enjoying my new hobby
Heating labels and unscrewing screws is like tapping your head and rubbing your stomach. Man, it's a tough wait waiting for your monthly videos!
Were you able to test the power supply after changing out the capacitors? Maybe use a known good power supply and test the rest of the board? It might help narrow down where your issue is...
this brings back memories lol. there is 4 places to check all of which are basically continuity checks, there is a fuse on the PSU while you are here check the cables and connectors, they are prone to broken solder joints, check the traces near the clock capacitor, the power board on here check the buttons, and the expansion cables/connectors.
Yes a part 2!!, I recommend looking for the original schematic, would help you tremendously
Problem is that most companies don’t release schematics. Not sure about the OG Xbox though
@@indy5280 Yes that’s unfortunately true, and also many schematics can’t be attained without it being behind a pain wall, but I think a technician or engineer might have knowledge to recreate it
@@Kakusuo True. People have figured out gameboy game pcb’s so maybe a person who loves a system enough could make one
I bought my Mtn Dew edition Xbox about 8 years ago, also no power issue, just took a power supply out of a spare parts Xbox with same motherboard revision, works great to this day. Great video
That's a beautiful OG Xbox
To be fair I think it's f****** ugly I like the original Xbox look
Agreed!
I believe in you man. Let’s get it working. And yes you are inspiring me to go back and start workshopping old electronics which was something I did as a kid but not to this level before the internet
There are 4 traces on the underside of the motherboard, they run right along the front edge and then up the right side of the board. Those traces often get breaks from leaky capacitors. Those traces i believe are related to the power and eject buttons, so if they are damaged those buttons may not work at all.
I'm impressed that you removed the heatsyncs without being able to power on the console. Those are basically superglued to the dies until you apply heat.
Its an alkaline. the opposite of an acid. That's why vinegar (a real acid) neutralizes it :)
Chemically, it’s considered a “base”
Wow great find. Love your work and the way you keep these museum pieces going.
Wanna see this Xbox brought back to life, can't wait for video 2!
I have a ps3 fat 20 or 40 gb that I owned since new still works flawlessly. I’d love for this guy to put new thermal paste in it
Hello you should check the continuity between the front panel power and eject buttons and the PIC microcontroller on the motherboard. I fixed mine using a soldered wire between the 2. Absolutly worth a try 😊
I second this. Clock capacitor leaks usually is the culprit and the PIC rewire, usually does the trick.
As some have said, test the button continuity because the clock cap can cause issues there. Also, with a foxlink PSU the four solder joints for the power plug are worth taking a look at. The two outside joints are mount points its the inner two you want to re-flow solder to because they're notorious for bad solder joints.
This is so crazy you doing this video right now. You’ve been a big part of why I have gotten into the mod old console hobby recently. I’m actually in the middle of an og Xbox spruce up myself and actually got mine from the goodwill auction
That's awesome! Good luck with your repairs!
@@Tronicsfix thank you! Looking forward to the next video on it. Since my comment I plugged it in and heard a loud pop and now it won’t power on lol.
i wish Xbox would have kept that case over the years. TONS of room. i dropped it a couple times ZERO ISSUES
@Tronicsfix Steve, thank you for all your videos I really enjoy watching you fix broken electronics! 🎮👾🖥️💻
Vinegar is an acid. If it neutralizes anything, then the cap must have a base electrolytic and not acid.
That's why I stopped buying a lot of stuff, prices are too high. I started fixing all kinds of
electronic things and vacuums 2010. Not as advanced as you do, you are top-notch.
Laserbear sells replacement feet with the screw holes pre cut. Pretty handy!
Good to know! Thanks for letting me know.
Oh I use a straight edge box cutter to carefully remove labels. Heating them up works for most but those metallic ones just crumble no matter what you do. You did great with the tweezers too.
6:20 I was going to say "oooh, fancy!" about your vinegar bowl, but using a heavy crystal bowl for vinegar or IPA is a legitimately good idea. Something that heavy isn’t going to tip over if you brush it with your hand, and why buy new when you can repurpose old?
Lol, yeah, that's why I used it...and partially just because it's what I had.
Another great use for an old “candy or condiments” bowl.
I did put thermal paste on my PS4 by watching your videos. No more fan noise. Thank you!!!
You will figure it out Steve Don't give up. Capacitors generally comprise a conducting salt based on long-chain aliphatic dicarboxylic acids and also a solvent, for example ethylene glycol. An example of a conducting salt used is dodecanedioic acid, which is generally used in the form of ammonium salts.
I was going to say the same thing!
It's surreal seeing the notes on the box and knowing it was shipped FedEx. Glad it got to you.
that bubble-gummy thermal paste might be a phase change material, which "liquefies" when hot and fills all the micro structures on the surface
It definitely gets softer when hot
@@Tronicsfix No comment....
(now you know someone had to say it....)
I loved the Secret Agent action section!
8:55 aye, caps are basic - you're using vinegar (an acid) to neutralise the leakage
Im excited to see the 2nd video on this xbox repair. Its always interesting to see the process of working through the individual circuit board components too bring back old tech. Thanks TronixFix.
awesome!
I'm not into computer repair but Xbox has always been my console of choice so this interested me.
I'm going to subscribe just because I want to see you resolve the issues in part two!
I hate Goodwill so much. Taking donations from people and still price gouging. Special place in hell for that company.
So, they should resell something for significantly less than market value and so leave a larger margin for the next reseller? 🙄
FWIW, there are some great deals to be found at thrift shops -- just not in video games. I am an avid bibliophile, and I once purchased a vintage book about Princess Elizabeth (as she then was) for about $.50; the ABE online price was around $60.
It is just not possible for _all_ products to be listed at market price; the key to success in collecting is finding those niches that are undervalued and exploiting them.
@@williamharris8367Goodwill specifically has all kinds of issues over wildly overpaying executives and turning local organizations into petty fiefdoms.
Their mission is charitable work, selling donations is how they raise money. The higher selling price allows them to do more charitable work. They don't set these prices, the market does. Be angry at the market instead.
@@williamharris8367exactly right. Rather have goodwill profit than your garbage reseller/picker
The reason why Goodwill has gone up is because of the resellers looking for a fast flip.
Used to love watching these videos, also would get things off goodwill, now ever since this video when I go and look at games everything is wayyyy over priced used to be able to get things at good price, dont understand why you had to go blow it up just for some clout… glad it made you feel good though☺️☺️
Picked up a As is xbox one S from the pawn shop for $20. Hook it up and it kept throwing the error 102 , 106 codes. I knew it was a bad harddrive. Found my old laptopi n the closet that had a 1 terabyte harddrive . Formatted the harddrive , download xboxes firmware and the update. Now I have a working white xbox one s for nearly nothing. The ifixit guide helped me out . Thanks Ifixit
I love working on these old OG box's. You never know what the problem is going to be. I aquired three from a flooded basement. All corroded, rusty and nasty. Took me a while but I restored all of them.
Really enjoy your videos. I’ve been watching for a while now. Your videos have helped me troubleshoot and fix my stove circuit board, guitar amplifier, and a few elite controllers.
Appreciate the videos
Great video! :D The only thing is that the folding animation around 7:30 to 7:40 ish actually made my heart drop. I thought u snapped the board in half 😭😨😱 Amazing videos though. I love tech.
I still have my OG Xbox back when i got it in 2008. Still running strong after a full recap, DVD drive swap, multiple HDD upgrades, and an HDMI mod. One of my favorite consoles.
The Mountain Dew Console is definitely one worth saving, and a favorite of mine. The color is just great. I certainly would of tested output power before reassembly. A fuse is the start point. But if there is no output power no reason to look at the board yet.
first thing to check is there voltage on the on switch ,if not check all the voltages from the psu ,if there is none (not all lines will be active in the off state)check any fuse on the psu ,if ok look for a high value resistor on psu (there may be two in series)they/it suply a start up voltage to the chopper chip .good luck with the repair
You can do it Steve, you're the best! Hug from Portugal ✌️👍
You'll get it! I got faith in ya! Keep up the great work!
love the funky music when you were installing the capacitors! 😄
A few tips.
Check for the fuse in the power supply, check that the front panel connector was plugged in, and as chris tursk mentions, check the front panel traces on the underside near the clock capacitor (segments 6 and 7 along the edge). Those will probably be PE#1 with the clock cap leaking. Strange though, usually I've seen it power on immediately when the console is plugged in in the wake of that damage, try the eject button as well to turn on the console (though that's also victim to the trace rot, along with the front panel LEDs and power trace).
And now I really want to see that xbox working, don’t give up!
Hey the music between the soddering shots is a great addition to the videos. Way to go!
It's easier using an Exacto Blade to get label corners up once you do you need to go slow and get heat under where you have it peeled up a actual heat gun almost to hot I feel a hair dryer works better. Nice find I hope you can get it going in the next video thanks!
Yay, a part 2. I know its harder for you than me, but now I have something to look forward too.
I actually placed several bids on that Xbox to see how far it’s go. It all makes sense now knowing that highest bidder was willing to pay so much to just to have content material. I was the one who complained on Reddit about how people pay so much for these even for a dead nonfunctional unit
One good trick to know is that the vast majority of capacitors on a board are irrelevant. They can be removed and just kept as an open circuit as that is their effect in a DC circuit. Capacitors are used to smooth out the waveform of the voltage (which for DC is flat so no waveform). Also the bigger they are, the less useful they are (unless you are connecting the power supply to AC which needs big capacitors).
There are some specific places where a capacitor is important, but those are rare.
Big ticket obvious and critical items
Main Fuse and secondaries?
PS output- Isolate problem there and if, use another.
Clock circuit for corrosion as if that ant working, its a door stop!
Visual check over board to see if you missed something
when item is totally dead, work from PS forward through secondary caps or mosfets where board gets input power- This after you look for obvious damage on board.
I would have first checked voltage and current on the supply, fuse... If the supply is fine, I would go to the motherboard. good luck with this repair!
Great work on these really cool X Box. I hope you do part 2.
For older consoles like this, that you know people are highly unlikely to open up and replace the thermal paste, I would suggest using a carbon based thermal pad instead. It has the same qualities as thermal paste but has no requirements to be changed out once it dries up. It'll continue working forever, as long as the console still lives. I did the same thing with my Xbox 360 (OG Halo 3 Launch console) and it's been running for years without any problems.
Mostly just pointing it out since most people wont think to replace thermal paste on older consoles.
You're awesome! These videos are super helpful, and cathartic. Thanks for sharing.
Tip for removing labels/stickers is to put denatured alcohol in a syringe and after heating and getting 1 corner up a tiny bit, shoot the denatured alcohol behind it the label or sticker and lift slowly and it should come off really easily and then let it dry and all the adhesive will still be good after the alcohol evaporates
The PSU has a known fault of dry joints towards the 110v input. The boards also suffer with trace rot. There is a long trace at the front of the board for the pwr switch. The eject button will also turn on the console. The latter is worth checking but i would suspect the psu in this case.
I picked up a Mountain Dew Xbox a few years ago and it was a pretty good deal at around $300 US. It still appears to be absolutely immaculate condition and I've rarely seen another original Xbox that looks as nice. (I was a bit suspicious at first that it might have been a fake but everything with the case and internals has checked out as original.) Plus it already had a TSOP flash mod and an upgraded hard drive - which I upgraded again to 2 TB drive.
Acetic acid (vinegar) does not neutralize another acid. However, it does remove corrosion, but at the loss of more metal. Maybe you should find PH testing strips, distilled water (~7), and cotton swabs to know what's on the motherboard. Wet a swab, rub suspect area, and swipe along test strip.
Have you checked the output voltage of the power supply? I would always recommend to do this when you fiddle with old hardware.
Un-Du works great at removing adhesives and it dries almost instantly. I use it on everything and always have spare bottles available. Currently, 1 being used, 2 spares bottles and a 32 oz refill bottle. Just make sure to get either the yellow or white caps as the silver cap, California sales specifications, doesn't work.
Look at those ribbon cables 😂😂😂 that brings me back
I LOVE THIS CHANNEL
Thats lovely shade of green, can’t wait for part 2
Hopefully this Xbox can be brought back to life,Also that board has the free pads to install additional ram!!! :)
This is my dream console. I'm so insanely jealous you got to work on one 😭😭😭😭😭
These are my favourite types of videos of yours.
Check the traces on the Clock compasitor. There are 3 traces that can get affected and they are used to power it on.
Had a several of them to repair with that issue
Happy to see a video this New year! for the Stickers i use always a hair dry stet of a hot air because so you dont burn the plastic and also it looks like u have never open the console this trick is almost 15 years old, old school trick for keeping warranty! you can try it just ask your wife for her hairdry . srry my english not that good. God bless U from Germany
*hairdryer srry
You can do it ❤ We are waiting for the second part
I use to work for an electronics manufacturing company, that made all sorts of stuff , and when we would clean the product's, they would use like an industrial dish washing machine, and after it was sent through, then you take out the product and let it air dry over night .
The power socket pins often come loose on the Power Supply. That led to a Safety Recall, but reflow and adding extra solder to reinforce.
Thank god a second video is coming! Hope to see it tomorrow!!!
I'll waiting for the next chapter. Thanks for the video.
I'd recomment cleaning out the holes as well and use all new solder, instead of just heating up the old solder and pushing the new cap through. It'll not only remove any cap juice residue, it's also safer for plating at the through hole.
I have a regular XBOX with the same problem. One day it was working and the next it wouldn't even power up. Opened it up and found some bulging caps that I replaced, but still not working. It would power up for a split second before shutting down. I checked the power rails from the power supply and they were higher than they should be. Quite possibly there might be some over voltage protection on it shutting it down. Still haven't figured out what's wrong with it, so I wish you the best luck. Maybe I can get some pointers from the next video!
This was certainly a fun watch after replacing the capacitors on my cousin's childhood OG Xbox yesterday. First time doing it, and it was a success! I wonder what could be up with this one though. Possibly bad traces from the clock capacitor leak?
Awesome great content can't wait to see part 2 etc and thanks for showing us how to repair our electronics and fix it . happy belated Christmas and new years. I can't wait to see what you repair next etc
What a nice xbox! Great video.. as always
Isn’t it amazing that with the technology we have at our disposal nowadays the humble toothbrush is still the best tool for cleaning stubborn stains on a board.
Also I would highly recommend A mod chip. And not for piracy, but for being able to rebuild the hard drive and installing a new hard drive. Then you can reinstall the stock o s and still use the console without the security on the console
A bad fuse is the most likely suspect but check things like NON electrolytic capacitors as well if a fuse swap dose not get the job done. Also go over the entire board to look for any burned out components . The point of a fuse is to blow instead of the other components frying but something could of been blown by a good surge.
U can check the output of the power supply. It's same as a computer power supply. Just short the green wire with black ground wire. Check if psu is giving out voltage
I had an og Xbox and I heavily modded it. Added a usb port, bigger hd, replaced dvd drive with a LG, obv modchip, cleared out top Xbox logo and put a led light
My childhood xbox died and I wound up tossing it before I learned how easy it is to bring back to life. Now I go out of my way to make sure they have new caps and have been restored and not just refurbished