I Explore Rare Mechanical stages // A Thrilling Repaired of Broken Giant Gear From Thread process

I Explore Rare Mechanical stages // A Thrilling Repaired of Broken Giant Gear From Thread process…
#iexplorerarerepairing#thrillingrepairedofgear#Brokengearrepairfromthreadprocess#pkprocess

[@timshal2]

Its nonsense holding gear by not finished surface it's dumb because inside hole will not be in center after all he must use center hole

[@timur-wo3sv]

У него там биение жесть будет

[@jimmyplain7583]

Never worked in a machine shop? The casting looks like it's out of round, but the center hole is bored, and the outer surface is parallel to it. And as you can see, it's perfectly machined and still parallel to the center bore.

[@timshal2]

@jimmyplain7583 it can be parallel but not perfectly in center even half mm can damage gear.

[@cafe6010]

@@jimmyplain7583 No, he did not center the inner bore on the machine, watch when he takes it off, you can see.

[@williamhoward8319]

i may sound a bit ignorabt but should the part be better centered in the chuck

[@ВасКо-в2с]

This is Pakistan! In addition, the gear does not shine with quality either... And it will do!

[@user-bl1mi4tr7o]

Это тот случай, когда улучшать - только портить. Сточить зубы косозубого колеса с твердостью поверхностного слоя 65HRC резцом из быстрорежущей стали с твердостью 60-62HRC уже показывает уровень качества. Так что отсутствие радиального биения зубчатого венца, относительно оси детали на уровне 0.01 мм - меньшее из зол. И оскомину набил вопрос, почему показывают ремонт, а не работу отремонтированных деталей(риторический вопрос).

[@mauricioalfonsoleealvarez.6169]

Super. Muy inteligentes y no se dejan varar. Felicitaciones.

[@wawansetiawan4042]

Very good.👍👍👍

[@edswider9309]

This job has a very tight tolerance

[@willfromhythe]

It fits where it touches 😉

[@ThachMechanic]

Your skills are very good. I need to learn a lot from you

[@ilyas.3181]

Биение не устранили теперь агрегат будет шуметь и не долго будет работать, будет износ. Мастер за изобретательноть 5 а за работу 2.

[@paultabone2010]

You are very talented with your job 👍

[@pk-process]

@@paultabone2010 thank you so much…

[@andrzejporeda7281]

Super jest to zrobione pomyślane i wytoczony pozdrawiam serdecznie.👍👍👍👍👍👍👍👍

[@patrickdewhirst8125]

wow recycled indeed.. RESPECT SIR.

[@sergiocalpiriz6275]

Pregunto porque no sé! Pero no lo dejó muy fino al engranaje no le sacó demasiado con el torno y le quedó poco cuerpo???

[@hamiltonsoldasbh7554]

Muito bom

[@рыбалкавпоморье]

Офигеть, при помощи рулетки такую точную деталь выточить.

[@Alex_Ander77]

Точную? Не факт 😂

[@ВасКо-в2с]

@@Alex_Ander77 Это был сарказм!

[@roman8724]

Not sure what this gear goes on but I'm guessing the machine must vibrate like hell with a off center gear like that😂

[@mainsource1787]

Excellent job but i think its better to add some pins in addition to welding to ensure it will last longer

[@erikkos4788]

Très beau travail 👍!

[@francescofalcone7394]

Bravo complimenti

[@ВячеславМихайлов-р7ч]

Очень хорошо, молодец.

[@robettarmstrong6108]

He welded it then turned the weld off?

[@zango04]

je vois pas trop l’intérêt de faire un filetage,tu emboites les deux pièces tu soudes et puis c'est bon

[@bernardreilly7519]

Excelent better than most U Tube vidieo Bernard Glasgow Scotland

[@paulorth2251]

Now that was patience and attention to detail to get te fit correct and maintain the proper diameter on the gear. Nicely done sir. 😊

[@samrodian919]

But what about the appalling non concentricity of the damaged gear when it was being turned off and then the ' thread' put on? The thing is at least 200 thou out of concentricity. The finished gear will end up going in and out of engagement with its neighbour.

[@cafe6010]

I admire the hard work, but this is not good. The inner bore was not centered to start with and that ruins it. 2nd thing is that both should have been machined smooth with a too tight fit. Then the inner could have been chilled and the outer ring heated and the two halfs put together then.

[@danielsplayhouse3804]

Just the vibration of cutting the teeth off that gear would drive me crazy... I will say that they make do with what they have at their disposal!!!! 😁😁😁

[@justinmijnbuis]

no sure how strong this is compared to the original but the repair is genius.

[@williamhoward8319]

grind a chip breaker into your carbide may help

[@abhaykumarsinha]

It looks that centre is not aligned.

[@hancecrawford]

good bit of clever engineering much learning

[@jeffreylynch3203]

You’ve heard of third world? This is like 8th or 9th world.

[@user-Mitiay]

Он его даже не поставил по центру!!!😂😂😂😂😂😂😂😂😂😂😂😂

[@MrNeverseeme]

Wow that's some Mickey Mouse stuff going on here.

[@danielsplayhouse3804]

You know what kind of stuff I can make with a machine like that here in the US I would love to find one like that... People charge 7k + for one....

[@ГарриМуллан]

Не уверен, у шестерни будет биение относительно центра

[@MonicaDenis-wr9jj]

salam vean y aprendan

[@RanjitSingh-h8b]

Good work 👍

[@chaiwatpotichanid]

🥰🤲salamat kupchak ❤

[@user-fz8my8wc6k]

фуфло. не отцентровал. всё отвалится

[@edswider9309]

Definitely precise

[@user-no4gw4qr5r]

Смысл в резьбе?

[@carlos-oz2go]

This one looks like it could really work! Not like a lot of the others.

[@CarpinteroJesus]

You have no respect for our time, don't you know about something called editing?

[@pepebruno]

💪💪💪💪👍👍👍👍👏👏

[@ragupathi4356]

I d not center

[@nikolaos9906]

Congratulation very good work

[@billypelkey4766]

I am impressed