I’ve tried three solid privacy wood fences with swing operators and they always get destroyed on really windy days. I’ve done two dual swings and one single swing. I think the best option for a privacy swing gate is to build a ridiculously strong hinge post with like a 3 ft by 3 ft concrete footing and a steel post or a concrete post then make a single gate with 2” square steel tube welded frame then screw wood panels to it and have a electronic latch on the other side so it can lock when closed. You also need 7” bullet hinges and make a custom steel bracket attached to the arm made of 1/4” steel. But you still run into the problem of it not working when it tries to open into strong wind because it’s going to sense an obstruction and if it’s strong enough to push through the wind it could be dangerous and crush a person. The best way to make a privacy automatic gate is a rolling gate.
That is one option, but so many make the same mistake by not buying the proper operator that can do the job. In this video those look like either GTO or Mighty Mule, basically the same stuff. Not designed to handle the wind load you mention. Every manufacturer lays ourt in their spec on what length and weight their operator is designed to handle. This type of operator is no good at handling privacy gates with any wind load. There is one that can do the job if the gates aren't too long and the weight is reasonable. That would be the Maximum Conrols Strong Arm 2300. I install and service automatic gates and have done so for 23 years. I have made it a point to learn what works and what does not. This gate should have a steel frame, steel gate posts, and better operators.
Thanks for the suggestion. My problem is that I look at big box stores like Home Depot or Amazon and do everything diy. I kind of figured there is a commercial or industrial grade option for any type of gate if you have enough money and don’t mind paying for freight and are going to do some welding and custom fabrication.
@@curtcmiller Good question. generally speaking, I like the LA400, but not for a privacy gates. Even Liftmanster will tell you this if you call their tech support and tell them what you plan to do. The Strong Arm 2300 is the only system of the actuator type that can handle privacy gates,. Even those may not handle huge privacy gates. Good Luck.
About to install mine next week just having problems with the gates dropping a bit when fully open, hopefully will he rods to support the 4x4s will do the trick
@@qmyers367 Please see my earlier comment. The gates should have a minimal steel frame, properly constructed and preferably welded. the wood can be attached to the steel, and you must use automation capable of handling the wind load that a privacy gate has. What ever these operators are, they will not handle ANY wind load.
@@Nateboy1236 First, read the comment by @kanisohana below. the wind load on "privacy gates is incredible. The operators in this video will not be able to hold up to any wind at all. Trying to get those operators to lift a gate is way beyond their design parameters. there are systems made to lift gates vertically. Look them up and see how it's done.
I've been trying to figure out how to make the gate open outward from the controls instead of in. How did you set this up and did you need extra hardware from the manufacturer to make it open that direction?
This is incorrect, Almost every automation manufacturer makes hardware available that allows for outward opening instead of inward. Also please see my comment above.@@jonnyeagle839
we built a gate similar to this but the wind is constantly forcing the doors open and shut. I'm concerned it will break the openers. Has yours been fine?
From what I’ve seen, mind you im not a pro installer however what I’ve seen makes sense. If you live in a super windy area I don’t believe there’s any opener you can use that will support the wind from a solid privacy fence like this, now if you went with like a chain link, iron bar etc where the wind can pass through you’d be able to run this.
Any recommendations for a back gate with 2 swinging gate inward and or outward. ( I have an alley in the back of my yard and would love to install anything that would open the gates with out me getting out of the car and manually opening it by hand, and I live in a not so safe of an area in Cleveland Ohio, I thank you for ur time 🙏 🙇🏻
How is your gate and motors holding up? Do you still have it as a solid panel? Ghost controls recommends not to do so. I’m working on mine at the moment and have removed some pickets so the wind can pass thru.
At least make the supports 45 degrees, anything less than that won’t transfer the load back to the post but will instead shift it downward to the ground causing drag and leaning
It has to be installed properly. It sounds like yours was not. but there are much bigger issues with the featured installation. Please see my earlier comments.
@jonnyeagle839 no I'm just talking abt the fact there's no sencors on it and it's definitely not keeping a car from going right through it with minor damage
@@carcountry I think some people like the raised heartbeat and sudden shot of adrenaline as they try to race the gate before it either shaves the paint off their car or they take the gate off the hinges
I’ve tried three solid privacy wood fences with swing operators and they always get destroyed on really windy days. I’ve done two dual swings and one single swing. I think the best option for a privacy swing gate is to build a ridiculously strong hinge post with like a 3 ft by 3 ft concrete footing and a steel post or a concrete post then make a single gate with 2” square steel tube welded frame then screw wood panels to it and have a electronic latch on the other side so it can lock when closed. You also need 7” bullet hinges and make a custom steel bracket attached to the arm made of 1/4” steel. But you still run into the problem of it not working when it tries to open into strong wind because it’s going to sense an obstruction and if it’s strong enough to push through the wind it could be dangerous and crush a person. The best way to make a privacy automatic gate is a rolling gate.
That is one option, but so many make the same mistake by not buying the proper operator that can do the job. In this video those look like either GTO or Mighty Mule, basically the same stuff. Not designed to handle the wind load you mention. Every manufacturer lays ourt in their spec on what length and weight their operator is designed to handle. This type of operator is no good at handling privacy gates with any wind load. There is one that can do the job if the gates aren't too long and the weight is reasonable. That would be the Maximum Conrols Strong Arm 2300. I install and service automatic gates and have done so for 23 years. I have made it a point to learn what works and what does not. This gate should have a steel frame, steel gate posts, and better operators.
Thanks for the suggestion. My problem is that I look at big box stores like Home Depot or Amazon and do everything diy. I kind of figured there is a commercial or industrial grade option for any type of gate if you have enough money and don’t mind paying for freight and are going to do some welding and custom fabrication.
@@rentaissancemanhow do those you mention compare with Liftmaster LA400Pkgul?
Or is Liftmaster on par with Topens , co-z , Ghost, etc
@@curtcmiller Good question. generally speaking, I like the LA400, but not for a privacy gates. Even Liftmanster will tell you this if you call their tech support and tell them what you plan to do. The Strong Arm 2300 is the only system of the actuator type that can handle privacy gates,. Even those may not handle huge privacy gates. Good Luck.
I installed a zombielock so the gate latches, and stays put when windy, plus dogs can't push on a gate and slide through.
About to install mine next week just having problems with the gates dropping a bit when fully open, hopefully will he rods to support the 4x4s will do the trick
Gates should be made with 4x6 or 6x6.
@@qmyers367 Please see my earlier comment. The gates should have a minimal steel frame, properly constructed and preferably welded. the wood can be attached to the steel, and you must use automation capable of handling the wind load that a privacy gate has. What ever these operators are, they will not handle ANY wind load.
How did you handle the wire from one motor to the next? Did you cut a small channel in the asphalt?
Can you use something like this to open vertically?
NO!
@@rentaissancemanwhy no
@@Nateboy1236 First, read the comment by @kanisohana below. the wind load on "privacy gates is incredible. The operators in this video will not be able to hold up to any wind at all. Trying to get those operators to lift a gate is way beyond their design parameters. there are systems made to lift gates vertically. Look them up and see how it's done.
Any issues with weight, wind on the control arms?
How's the ghost controls holding up? Any issues?
I have mine for 3 years now and it works fantastic.
@@willtacoma2ndgen661 what kind of gate?
Where did you get the motor assembly. This is exactly what I am looking for.
Hi, did you ever find out what kind it is, I’m looking for the same one, thanks for ur time
@@sneekysmurf4754 not yet but still looking. Let you know
@@scottsmith8362 thank you 🙏,I appreciate ur time
@@sneekysmurf4754 Amazon
See my comment above.
I've been trying to figure out how to make the gate open outward from the controls instead of in. How did you set this up and did you need extra hardware from the manufacturer to make it open that direction?
Reverse the wires going to the motor, or if there is a switch tell it to change the handing. Right/left
This is incorrect, Almost every automation manufacturer makes hardware available that allows for outward opening instead of inward. Also please see my comment above.@@jonnyeagle839
we built a gate similar to this but the wind is constantly forcing the doors open and shut. I'm concerned it will break the openers. Has yours been fine?
Cutout some decorative design like square or round so wind can flow thru .
In your experience will these gate openers hold up? I was told by the manufacturer they wouldn’t hold up because of wind?
From what I’ve seen, mind you im not a pro installer however what I’ve seen makes sense. If you live in a super windy area I don’t believe there’s any opener you can use that will support the wind from a solid privacy fence like this, now if you went with like a chain link, iron bar etc where the wind can pass through you’d be able to run this.
Any recommendations for a back gate with 2 swinging gate inward and or outward. ( I have an alley in the back of my yard and would love to install anything that would open the gates with out me getting out of the car and manually opening it by hand, and I live in a not so safe of an area in Cleveland Ohio, I thank you for ur time 🙏 🙇🏻
@@sneekysmurf4754 I am in the exact same boat. Did you end up finding anything?
@@nolanprequels2764 no not yet but I’ll get to it within a month
@@sneekysmurf4754 let me know! I’m doing some research too but hoping to get something installed this summer
How is your gate and motors holding up? Do you still have it as a solid panel? Ghost controls recommends not to do so. I’m working on mine at the moment and have removed some pickets so the wind can pass thru.
See my comment above.
What make model is the opener?
What battery are you using?
Where can I buy , the openers??
At least make the supports 45 degrees, anything less than that won’t transfer the load back to the post but will instead shift it downward to the ground causing drag and leaning
That is only one of the problems, Please see my earlier comments.
The gate opens automatically the machine gate it makes gate open and close the gate actually getting closing
I'm wanting to set mine up similar because I don't want the actuator fully extended when gate is in closed position
see my comment above.
We bought a gate with all the setup stuff from a company called Annapolis Metal Works. Worked out well
Psalms 24... your gates control your gait. Glory to the Lamb of God! 😊
How much did this cost?
Gate 2000, operator 400 wiring free from fly by night electric
How much opener remote
Someone installed the same one on a house I rent , but the doors don’t fully open , does anyone knows how to fix this one issue?
It has to be installed properly. It sounds like yours was not. but there are much bigger issues with the featured installation. Please see my earlier comments.
Do you provide phone call assistance Or no
You're gonna have issues with wind
Absolutely!
Definitely not safe
You're right, if someone doesn't hear that constant grinding away they might get pinched while it keeps cycling like that
@jonnyeagle839 no I'm just talking abt the fact there's no sencors on it and it's definitely not keeping a car from going right through it with minor damage
@@carcountry I think some people like the raised heartbeat and sudden shot of adrenaline as they try to race the gate before it either shaves the paint off their car or they take the gate off the hinges
@@jonnyeagle839 exactly cuz that shit closes slow asf
Not to mention that those gates present a wind load that will destroy that automation in a heartbeat.@@carcountry
Shit gates or fencing should I say