I was riding normal, stopped at a red light and had no throttle when light turned green. Bike has 995 miles. Plugged in the diagnostic attachment and it doesn’t light up at all
I did a couple tests on the controller and it failed them so I replaced it. Fixed the issue and runs now. I put on an older used controller. Feels a little less torquey going up hill tho
I have a bike that’s blinking 17 times, says motor temp sensor failure in the chart you provided, any tips on how to fix or reset this? I can’t adjust my regen braking because it keeps throwing the code
I have the red light blinking 15 times. Apparently that means a short circuit from the throttle cable to the controller, do I just need a new throttle? Or is there a way I need to calibrate it
hi there, I would try turn your breaker switch off and let sit for a good 10sec then turn on again, see if that resets. Otherwise unplug the throttle wire plug, check theres no water in there and that the connection is firm. If all good then last thing would be to replace the throttle yes
My diagnostic cable just keeps blinking red continuously every 2 seconds until I turn the bike off. And I cannot turn off regen I’ve tried everything! HELP
What id your diagnostic cable doesn't produce a flash at all. I also lost visual on my screen. And now my bike is super unreliable works every 10 to 30 resets. I also get jolty speed (especially in economy mode) and the newest fault my sport mode sometimes will only reach 60kmh
Mines built with the 72/42 and the bac4000. Out of the blue I got no throttle. Thought it was done for. Tried restarting 10 times ready to give up then all the sudden it's good to go. Not sure what I did.
My diagnostic wire is just a soiled red light no blinking at on 3 diagnostic wires Sur Ron has never seen this I'm at a loss if you can point me in the right direction I would greatly greatly appreciate it
I have a issue with my Surron I installed a bac4000 on my x160 slowly it started to cut power when I would throttle it then no throttle would work , I swapped out the bac4000 and throttle it powers on but there’s no throttle response some please help
The red light on mine just stays solid, doesn't blink at all and there is no throttle response. There is power to going to the bike because the dash turns on, light turns on and I can charge my phone but no throttle response. I've tried a brand new throttle as well but the same issue; anyone have any ideas?
@AmpdBrothers this has been my problem for awhile now i've pulled out brake sensors kickstand sensor and tilt over sensor.. went through all the relay connections to see if any water got in or pinched wires but literally nothing i can see haven't been wet for awhile honestly needs a wash haha but yeah surely you know the root issue??
thx for the troubleshooting tutorial... i got a 22 blink after cutting and thermo tubing my kickstand wire and i was wondering why i had no more throttle. i had to reopen it and make sure the wire wasnt in contact with each other and thermo tube them back and it solved my problem.
My surron worked fine and did amazing for awhile..but now its stuck maxing out at 15MPH... is it my controller? my belt? i dont understand what the hell happened..yes green is cut ..
I crashed mine other day was getting 45mph in sport mode out of it before crashed it after I got back on it it won’t go past 31mph on sport mode anyone help me out with whats happened
Please help I have a 2023 Surron I used the diagnostic togal and it flashes slow ever 2 seconds I have deleted the break sensors kickstand sensor and tip over sensor the bike starts and runs but if you jump off a curb or accelerate fast it cuts all throttle response bike stays on but you have to turn the key off and back on to get it to start running agin I can’t figure out the problem any help please
My bac4000 is flashing 2 slow single ones then 6 in a row. I have all lights but no throttle. It's just dead. Hall sensor ?
my surron runs completely fine but when i plug the diagnostics wire in it doesn’t flash at all, could i have and explanation as to why?
I was riding normal, stopped at a red light and had no throttle when light turned green. Bike has 995 miles. Plugged in the diagnostic attachment and it doesn’t light up at all
Did you figure it out
@@AG-rj8bo I haven’t fixed it yet but I think it might be the controller
remove the tip over sensor unless you alreasy did
I did a couple tests on the controller and it failed them so I replaced it. Fixed the issue and runs now. I put on an older used controller. Feels a little less torquey going up hill tho
What tests did u do on your controller?
Will the cable work if I cut the region brake and limiter cable
I have a bike that’s blinking 17 times, says motor temp sensor failure in the chart you provided, any tips on how to fix or reset this? I can’t adjust my regen braking because it keeps throwing the code
Did you fix it mine is also blinking 17 times
The red light on mine doesn’t turn on at all. And I’m stuck with regen, any help?
I have the red light blinking 15 times. Apparently that means a short circuit from the throttle cable to the controller, do I just need a new throttle? Or is there a way I need to calibrate it
hi there,
I would try turn your breaker switch off and let sit for a good 10sec then turn on again, see if that resets. Otherwise unplug the throttle wire plug, check theres no water in there and that the connection is firm. If all good then last thing would be to replace the throttle yes
My diagnostic cable just keeps blinking red continuously every 2 seconds until I turn the bike off. And I cannot turn off regen I’ve tried everything! HELP
What id your diagnostic cable doesn't produce a flash at all.
I also lost visual on my screen.
And now my bike is super unreliable works every 10 to 30 resets.
I also get jolty speed (especially in economy mode) and the newest fault my sport mode sometimes will only reach 60kmh
Can u leave the light plugged in all the time?
Mines built with the 72/42 and the bac4000. Out of the blue I got no throttle. Thought it was done for. Tried restarting 10 times ready to give up then all the sudden it's good to go. Not sure what I did.
My diagnostic wire is just a soiled red light no blinking at on 3 diagnostic wires Sur Ron has never seen this I'm at a loss if you can point me in the right direction I would greatly greatly appreciate it
I have a issue with my Surron I installed a bac4000 on my x160 slowly it started to cut power when I would throttle it then no throttle would work , I swapped out the bac4000 and throttle it powers on but there’s no throttle response some please help
my asi controller says it's locked i have a bac4000 it turns on but has no throttle response any help?
Any chance of getting a video on the vortex carbon pretty keen on it
Heya! Funny you should ask we are working on an in depth video on the full skateboard range and will be coming shortly. Keep your eyes peeled
@@AmpdBros that dope bro do u know what ECU it's running
@@pappasmirk. the latest hoobywing esc
The red light on mine just stays solid, doesn't blink at all and there is no throttle response. There is power to going to the bike because the dash turns on, light turns on and I can charge my phone but no throttle response. I've tried a brand new throttle as well but the same issue; anyone have any ideas?
I have the same problem if you fix it let me knwo
Lmk to plzxx
@AmpdBrothers this has been my problem for awhile now i've pulled out brake sensors kickstand sensor and tilt over sensor.. went through all the relay connections to see if any water got in or pinched wires but literally nothing i can see haven't been wet for awhile honestly needs a wash haha but yeah surely you know the root issue??
Have the same issue, let me know if you guys get it fixed. My light stays solid red aswell
Avez vous trouvé le problème depuis ??
thx for the troubleshooting tutorial... i got a 22 blink after cutting and thermo tubing my kickstand wire and i was wondering why i had no more throttle. i had to reopen it and make sure the wire wasnt in contact with each other and thermo tube them back and it solved my problem.
My surron blinks once slowly, and 4 times at a normal pace. What could be the problem? The throttle doesn’t work
What does 22 blinks mean
Mine blinks once slowly and 4 times at a regular pace. My throttle doesn’t work. Can someone help me?
My surron worked fine and did amazing for awhile..but now its stuck maxing out at 15MPH... is it my controller? my belt? i dont understand what the hell happened..yes green is cut ..
I have the same issue! Did you ever figure it out?
@@billyjenkins3015 nope still looking for solutions.
I crashed mine other day was getting 45mph in sport mode out of it before crashed it after I got back on it it won’t go past 31mph on sport mode anyone help me out with whats happened
Exact Same is happening to me right now
What does 2 fast blinks then 2 slow blinks mean
Yep that’s what I have too. Have you figured it out?
@@satellitehunter7440 not yet still doing research nobody seems to know
@@satellitehunter7440 any luck?
Got a bike flashes 16 times what does that mean
It is brake related. More than likely your brakes are active. Try restarting your bike
Mine does 2 normal blinks then 3 quick blinks then back to the 2 normal blinks
ther is flashing charts for surron x
Please help I have a 2023 Surron I used the diagnostic togal and it flashes slow ever 2 seconds I have deleted the break sensors kickstand sensor and tip over sensor the bike starts and runs but if you jump off a curb or accelerate fast it cuts all throttle response bike stays on but you have to turn the key off and back on to get it to start running agin I can’t figure out the problem any help please
did you end up finding a fix
@@SethNGB bad throttle sometimes they go bad out of no where bout a new Surron throttle and it works perfect 👍🏼👍🏼
What happens if it doesn’t blink at all
Not sure that’s happening to mine, too
Mine won’t blink at all
Le mien fait 23 flash mais il demarre pas aussu
When i turn on my bike the blinking just keeps going but slower and doesn't stop
Same! Did u ever figure it out? Sorry late reply
I believe it's saying all is good. But that doesn't mean the bike works every time.
Same
@@JasonJason-hv1lu mine was a controller problem but it was covered by luna they said it was very rare and i got a new controller
Thanks MOOOOOYTE!
6 flashes what will that be😕
Hall sensor
Mines not flashing at all
More than likely your controller has failed if you have also lost drive. check all your plugs too
I was riding fine then I stopped and turned off the bike
Then the throttle would not engage therefore the bike did not move
mines is opposite problem
I have 2 flashes
I’m getting 31 flashes
I got 16 flashes lmao
It is brake related. More than likely your brakes are active. Try rebooting your bike with your master air switch
My light is continuously on at all times! Everything works but no throttle! Hall sensor or controller blown or any ideas!
Bonjour, avez vous trouvez la panne depuis j’ai la même chose ??
I was riding fine then I stopped and turned off the bike
Then the throttle would not engage therefore the bike did not move