I just saw your video on this water pump. Great for farmers. HOWEVER … It made NO sense putting the pipes on top of the road/trail. AND it’s the same in your other videos. TY for the great idea(s).
This is Great engineering man good old school ingenuity same as the old ram pump. I enjoy watching no electricity or fuel motors.cheers from NewZealand
I hope that filling water into the tanks is done once only. Else, think of other good ways to ease the filling of water. Your ideas will benefit farmers around the world. Such a huge contributions. I give 5 of 5 stars.
The whole process is when the water that was filled in the drum is let go after closing the air and filler valves, the water leaving the drum creates a low pressure, which in turn pulls the water from the one way valve connected pipe which is the smaller intake. For the suction to build up to pull water from the inlet, the drum has to be higher than the outlet but the inlet can be way below the outlet. Examples are pulling water from standing well which are deep than the ground level. Once the cycle starts you can hear the water flowing from inlet into the drum.
the vertical tubing is called the anti knocking. It absorbes the water knocking or water ram. Without it it would destroy the tubing.... Creates a pushing motion also..
It works on the syphon principal Negative pressure is created It works only if your field level is below the level of water or same It not work to lift the water above the water level of steem Law of conservation of energy
That is why there is the drum. water loss in the drum (to outlet) creating a air vacuum thus water is suck from the water source by those vacuum. and the cycle goes again² (if you see some video of similar project using plastic barrel or weak old metal barrel, it got deformed) so more drum create more vacuum thus more water pressure.. two drum with two smaller pipe inlet (in video) for less pressure lose in the intake.
@@chinxenix7104 You only use the drum to get this siphon started. After that, you do not need any drum. If you find an other way to fill the tubes, then you could drop the barrel.
@@lesterjay9248 The arrangemet you are liking to can not work. No siphon can lift any water up from a well. To do that you need energy. In other words, you must fill the barrels by hand, again and again, and again.
The hight of the water is higher than the field. A simple siphon hoes prime with water will do the same thing no drum or other equipment needed other than a piper hose primed with water to suck in the siphon mode. On this build.
Are you trying to get this man hurt . LOL I had the same thought of doing that. I guarantee this guy has tried it and hopefully doesn’t put it on video LOL
sir thanks for your great sharing of this creative video pls guide me how to utilize the river water to water the rice field 30meter above river water level
Nice project.... thank you...is not clear for me what purpose have the back pipes in the base of the barels? That 2 short pipes that coming out in the back at the base of barels...
@@Learnn_for_Future , I also have the same question for those 2 small pipes below at the back. Are just merely spare pipes which are optional to install or have a purpose or necessary for the entire process?
He could just use a 4inch pipe with a ball valve a one way valve and a priming port to fill the line on a u-siphon and open the ball valve and let it rip
Hi there, could you show how you made the intake holes on the drums, what kind of fittings and how those fittings are installed. Thanks 🙏 I am asking because one the outlet the holes are original and all you had to do is screw the fittings on.
Maximum 10 meter. 1 Bar atmosphere pressure which is equal to 10 meter. So it will start taking water from intake when pressure reduce inside drum and out side pressure 1 bar
Now this is a siphon. No siphon can lift water up from a well to a higher elevation. The discharge must be lower than the water level in the source! That said, a siphon can lead water over a 7-10 m high wall, but you can not take out anything, not a drop, up there. Everything must down under source level.
Is the water level in the river really higher than the exit to the field? This siphon is no pump! Using a drum, no foot valve is needed. Two drums are not needed Vertical tube on the output is not needed. Mater valve at the output not needed. Output should have been dipped into a bucket of water to prevent air leaking inn.
sir sorry me i know what is the name of that things you put,in the river sir that's connect to the pipe sorry because I can not understand totally what you tell. .thank you for your answer 💖
FILLING WATER CAN ONLY BE DONE ONCE? ONLY IN THE BEGINNING? AND AFTER IT START TO FLOW WATER AT THE OUTLET THE WATER AT THE INLET AUTOMATICALLY FILLS IN?
@@Learnn_for_Future Am and avid fan of your project and is interested to make one for use in my farm. Requesting your to please advice the sizes of the following: 1) Suction Pipe; 2) Vent Pipe and Reducer (Suction Side); 3) Vent Pipe and Reducer (Discharge Side); 4) Discharge Pipe; 5) Discharge Nozzle Pipe and Reducer; 6) Name and size of the fitting attached to the drums.
He should have placed the components to suit his height for easy mandating. He should have used funnel to fill drums through pipes, to avoid wastage. A good try. More comments after I tried this myself.
There are two pcv pipe with the cap is closed and the other one with outlet to the rice field do they helping anything why need them on the barrel and the one is at the big pcv pipe
The vertical pipe at the outlet is useless. Waste of money. Pipes on the barrel is for filling the barrel with water. Using 2 makes it easier to fill via one while air is let out via the other.
It works like when you suck your drink from the glass using a straw, when the water from the full drum is release, it will create a vacuum in the drum and the vacuum will suck the water to normalise the pressure inside the drum, as more water is drained, more vacuum will be created, thus more suction. It is simple physics, maybe they don't teach physics in religious schools.
@@thomasmahoney9748 WRONG AGAIN, first it is not hammer pump but ram-pump, and the intake need to be higher than the ram-pump, and a ram-pump is only 10% efficient, 90% of the water is waster to operate the pump.
With a hose, you must find a way to fill the hose 100% with water. With a drum you do not need any foot valve at the input an do not need to fill the input pipe as log as it is reasonable short compared to water volume in the barrel. Besides, if there is a small air leakage, the barrel can absorb some air before the siphon stops.
Hello brother... It looks like working... But if it really works... Why you are not connecting an alternator or generator... ? I think its everyone's dream a free energy sources... Make it happen...
![Coheed and Cambria - Searching for Tomorrow [Official Video]](http://i.ytimg.com/vi/hDsYGLbmadg/mqdefault.jpg)
You do a very good idea with out electronic pumps pressure blessings
Thank you for showing us your ideas. A simple yet working pump for irragating our fields. More power to you, friend of the farmers!!!!!
But it only works if the river is higher than the rice field. It is a siphon with a priming barrel.
I just saw your video on this water pump. Great for farmers. HOWEVER … It made NO sense putting the pipes on top of the road/trail. AND it’s the same in your other videos. TY for the great idea(s).
Thanks for helping around the world Big Hello from Senegal!❤️🙏🏾
May God continue to bless you for being a blessing to us thank you very much
You're very intelligent 👌. God bless you. 🙌 I am an Indian.
Thanks sir God bless 🙏
So easy and l past to learnnig , that., gampang tuin amoh Mak proll,; gurih.,👌👍
វិដេអូនេះល្អណាស់។ខ្ញុំមើលហើយយល់ងាយៗអាចធ្វើបាន។ល្អសម្រាប់កសិករមួយចំនួន
Amazing job free energy pump free energy water pump good idea thank you sir
Why not show to us by using drum also in suction dide.to know if it is working or not.
This is Great engineering man good old school ingenuity same as the old ram pump.
I enjoy watching no electricity or fuel motors.cheers from NewZealand
Is there a certain elevation needed to suct water to the drum to the outlet pipe? ..
Wi it be possible to use this system from a 6 meters elevation to the drum pump.?
His is a siphon. A ram pump is something different. A siphin can not lift any water, a ram pump can.
Yes your very good idea without electronic presure good for our ricefield without irrigation like umiray philippines
I hope that filling water into the tanks is done once only. Else, think of other good ways to ease the filling of water. Your ideas will benefit farmers around the world. Such a huge contributions. I give 5 of 5 stars.
But it only works if source is higher than outlet.
The whole process is when the water that was filled in the drum is let go after closing the air and filler valves, the water leaving the drum creates a low pressure, which in turn pulls the water from the one way valve connected pipe which is the smaller intake. For the suction to build up to pull water from the inlet, the drum has to be higher than the outlet but the inlet can be way below the outlet.
Examples are pulling water from standing well which are deep than the ground level.
Once the cycle starts you can hear the water flowing from inlet into the drum.
Kako može voda sa nižeg ići u viši nivo bez pumpe
the vertical tubing is called the anti knocking. It absorbes the water knocking or water ram. Without it it would destroy the tubing.... Creates a pushing motion also..
@@aebniala No, it is a useless waste of money. Besides there is no water knocking in a siphon system.
Noop. Water level at the source must be higher than the outlet to the field. A siphon like this can not pump water up from any well.
It works on the syphon principal
Negative pressure is created
It works only if your field level is below the level of water or same
It not work to lift the water above the water level of steem
Law of conservation of energy
ruclips.net/video/BV0ZZoaYW6s/видео.html explain this then
That is why there is the drum. water loss in the drum (to outlet) creating a air vacuum thus water is suck from the water source by those vacuum. and the cycle goes again² (if you see some video of similar project using plastic barrel or weak old metal barrel, it got deformed) so more drum create more vacuum thus more water pressure.. two drum with two smaller pipe inlet (in video) for less pressure lose in the intake.
@@chinxenix7104 sir good day...so this kind of idea is working..? so that i will make also here in my farm...thnks
@@chinxenix7104 You only use the drum to get this siphon started. After that, you do not need any drum. If you find an other way to fill the tubes, then you could drop the barrel.
@@lesterjay9248 The arrangemet you are liking to can not work. No siphon can lift any water up from a well. To do that you need energy. In other words, you must fill the barrels by hand, again and again, and again.
This is all about DIY, simplest materials available that really works. keep it going bro from your new subscriber from the Philippines
Very good idea bro,
I do this in my farm,
Thanks for A wonderful project, thanks for Sharing Keep safe God BleS
Thats creative idea tks 4 sharing guys gbu!!!
The hight of the water is higher than the field. A simple siphon hoes prime with water will do the same thing no drum or other equipment needed other than a piper hose primed with water to suck in the siphon mode. On this build.
good job form thailand
thanks bro for the video more power
you are a hero to farmers...
Very good brother thanks for good idea
Very well my friend. I like your work
Sir , could you please tell me all size of pipe you use in this video? Thanks
Wonderful project...... thanks for sharing your ideas to us it has given me a widen Idea I will do this too
Sending full my supports👍😍🍀🌳☘️
It is not right to support people fooling people.
Excellent.
Try adding a water wheel to it 😉
Are you trying to get this man hurt .
LOL I had the same thought of doing that. I guarantee this guy has tried it and hopefully doesn’t put it on video LOL
make the funnel (imbodo) bigger so that you will not waste much water that you are hauling from the rice field!
Hihihihi 😁😁
sir
thanks for your great sharing of this creative
video
pls guide me how to utilize
the river water to
water the rice field 30meter above river
water level
Thank you you done good job
good I have learnt it . thank you very much
ThAts a good job thanks for the information
its so nice, good idea & job
Very good proyek
Nice project.... thank you...is not clear for me what purpose have the back pipes in the base of the barels? That 2 short pipes that coming out in the back at the base of barels...
@@Learnn_for_Future No, he is asking about the 2 short pipes with plugs on the "bottom" of the drums.
@@Learnn_for_Future , I also have the same question for those 2 small pipes below at the back. Are just merely spare pipes which are optional to install or have a purpose or necessary for the entire process?
It's just plug to seal the opening
000
@@Learnn_for_Future p00q
He could just use a 4inch pipe with a ball valve a one way valve and a priming port to fill the line on a u-siphon and open the ball valve and let it rip
Shuaia maluom Inglishi!
True ba iyan baka magastusan lang kami , kailangan ko Rin Sana Yan Dito sa taniman ko
Hi there, could you show how you made the intake holes on the drums, what kind of fittings and how those fittings are installed.
Thanks 🙏
I am asking because one the outlet the holes are original and all you had to do is screw the fittings on.
As vrea sa fie tradus in Romina
Question: is there limit on heights to pump the water. Like 20 meter from the water resources.
Maximum 10 meter. 1 Bar atmosphere pressure which is equal to 10 meter. So it will start taking water from intake when pressure reduce inside drum and out side pressure 1 bar
Its only 7 meters max acording to them
Now this is a siphon. No siphon can lift water up from a well to a higher elevation. The discharge must be lower than the water level in the source! That said, a siphon can lead water over a 7-10 m high wall, but you can not take out anything, not a drop, up there. Everything must down under source level.
What is the maximum distance the pump can pump water to?
And if the distance is 150 meters to the farm what can I do if I want to use this pump?
Please remember, water level in the river must be higher than the outlet for this to work. It is a siphon.
please tells us how did you install the pipe into the drum in details.
Please giveus the correct dimensions ofthe input and output plastic pipes and details ofthe drums which is help us to make a free energy water pump
Not critical. Use whatever you hve.
Please post all list of materials needed to install it.
Thanks 😌
Can u possibly install a gauge at the input pipe so to know the water pressure coming in? T q much
The water pressure at the inlet is one atu=1 bar.
Hi bro i like this video but really work this one 24 hours ???
Very good idea
Ho many meter pipe suction.nace for your idea
Hi brother will you live can you come make me one for my farms too
What place in the world this abundant place belong?
tuyet gioi luon ban oi
Is it non stop system continues suck water no stop? Or after some time will stop!
Билишимча сиз груч экасиз сизларда гручни нархи канча дулирга
Is the water level in the river really higher than the exit to the field? This siphon is no pump!
Using a drum, no foot valve is needed.
Two drums are not needed
Vertical tube on the output is not needed.
Mater valve at the output not needed.
Output should have been dipped into a bucket of water to prevent air leaking inn.
sir sorry me i know what is the name of that things you put,in the river sir that's connect to the pipe sorry because I can not understand totally what you tell. .thank you for your answer 💖
FILLING WATER CAN ONLY BE DONE ONCE? ONLY IN THE BEGINNING? AND AFTER IT START TO FLOW WATER AT THE OUTLET THE WATER AT THE INLET AUTOMATICALLY FILLS IN?
Yes, since it is air tight, as the water goes out it pulls water from the other side into the tank and fills it up.
Yes, but only if the water level in the river is higher than the outlet to the field. This is a siphon, not a pump.
what is the size of intake pipe do you use?
can you explain all parts of pump and specification means diameter(internal and external)
@@Learnn_for_Future Am and avid fan of your project and is interested to make one for use in my farm. Requesting your to please advice the sizes of the following:
1) Suction Pipe;
2) Vent Pipe and Reducer (Suction Side);
3) Vent Pipe and Reducer (Discharge Side);
4) Discharge Pipe;
5) Discharge Nozzle Pipe and Reducer;
6) Name and size of the fitting attached to the drums.
I am from Indonesia.
Please explain the size of the Pipe used in the process ?
If the well is 80 meters deep, can it draw water up like in the tools above?
No, even not one single inch. This is a siphon with a priming drum. No siphon can lift water.
Please tell me how deep well I should be maximum...
How many hight feet water capacity output slope 10.12 or 15
GOOD JOB
One video drum how to join four points...
Is the foot valve installed in the ibottom of the inlet tube the same as the one way valve in the ram pump
With a barrel, you do not need any vale at the input.
Hi bro I have done the same,but it's not recieve water from inlet vaccum recieved from the outlet
He should have placed the components to suit his height for easy mandating. He should have used funnel to fill drums through pipes, to avoid wastage. A good try. More comments after I tried this myself.
There are two pcv pipe with the cap is closed and the other one with outlet to the rice field do they helping anything why need them on the barrel and the one is at the big pcv pipe
The vertical pipe at the outlet is useless. Waste of money. Pipes on the barrel is for filling the barrel with water. Using 2 makes it easier to fill via one while air is let out via the other.
Good
Good project
thanks ... great job
It is only possible if the discharge level is below the suction level
WRONG, Same as a hammer pump these are pumping up hill. He has videos on the siphon pumps too.
You are very RIGHT. That s not going to work. No gravity pump.
It works like when you suck your drink from the glass using a straw, when the water from the full drum is release, it will create a vacuum in the drum and the vacuum will suck the water to normalise the pressure inside the drum, as more water is drained, more vacuum will be created, thus more suction. It is simple physics, maybe they don't teach physics in religious schools.
When you drink with a straw, does the glass have to be higher than your head????
@@thomasmahoney9748 WRONG AGAIN, first it is not hammer pump but ram-pump, and the intake need to be higher than the ram-pump, and a ram-pump is only 10% efficient, 90% of the water is waster to operate the pump.
Share for people that giving. Like this knowledge. Share it
I want to know the height of the inlet from the bottom of water source
can u install a 24 inches transparent tube of the intake pipe to see water flowing into the tank? thank you
Tanka akan suyu gösteremez yalan konuşuyor insanları kandırıyorlar
No need. Thos works fine, if, and only if, water level in the source is higher than at the outlet to the field. It is a siphon.
If he can really siphon water or pump it to higher level flow it back into the creek and power a waterwheel generator
right
Can you please design a pump for deep tube well 8 inch. Thank you
Use whatever tubes you have, BUT remember, this system only works if water level in well is higher than output to the field.
Hi, is the inlet pipe must be smaller compared to the outlet pipe? thanks
No, does not matter. Inlet can also be wider than outlet tubes.
What are two pipes on the lower side of inlet pipes
Why can't you get a funnel to fill the drum, funnel will save you time and effort. Secondly why do you have 2 nozzles under the intake pipe.
Sir how many hour it will work?
Hi bro,the source of water is about 40,feet deep? Can work siphoning method?
No, not even from a 1 cm deep well. A siphon can not lift water.
what is the deferennce betwen the tube design only and the with drum design?
With a hose, you must find a way to fill the hose 100% with water. With a drum you do not need any foot valve at the input an do not need to fill the input pipe as log as it is reasonable short compared to water volume in the barrel. Besides, if there is a small air leakage, the barrel can absorb some air before the siphon stops.
what materials used in inlet area that deep in the river is it gate
valve?what does name ?
No foot valve are needed at the input when using a barrel.
great
THANKS.
beast work
Best, not Beast.
Thais isso beatiful
Is there a check valve from the bottom of suction pipe
Yes, but not needed. Waste of money.
Can this system work for well, how much Suction hight it's work Sir.
@@Learnn_for_Future can you please calculate and describe materiel for 300 fit deep well
Can not lift any water up from any well. A siphon can not lift water!
雙桶的水力並沒有雙陪增加啊
Hello brother...
It looks like working...
But if it really works... Why you are not connecting an alternator or generator... ?
I think its everyone's dream a free energy sources...
Make it happen...
It works, but only if water level at the source is higher than the output. This is a siphon with a priming barrel
There is no vaccuum pressure in the tank that people think can lift up the water. To make sure, use vaccuum pressure gauge.
This works fine if, and only if, water level in the river is higher than the outlet to the rice field.
@@kjellg6532 So it is a siphon principle. Then there is no need such a tank.
@@irwana4265 That is right, no tank is really needed, but can be practical to get the siphon primed. When running, there is no need for the tank.
Awesome
I missed the function of the air compression
wow very nice
Wow, very bad!!!
It's amazing project I like it
I like it bro
Nice
iside the drum sir? is the pvc pipe passed thru the other side of the drum & you make a hole on it. pls explain further to me on my email