Installing Floor Insulation in my Van - Ram ProMaster Van Build Conversion - Episode 5 | Jason Klunk
HTML-код
- Опубликовано: 18 апр 2020
- In this video I start the process of insulating my floor in the ProMaster. I used 3/4" Polyiso rigid foam board for my insulation. I had a lot of trouble finding it in southern California, none of the big box stores carried it. I ended up being able to custom order some through J&B Materials. They were super helpful, give them a call for any building supplies if you are in the area.
We’ll finish up installing the subfloor in the van next week, yewwwwwwwww!
#vanbuild #vanconversion #rampromaster #campervan #subfloor #vaninsulation #floorinsulation
Rattletrap Sound Deadener: amzn.to/3zcV4MX
Miter Saw: amzn.to/2yoZ8A3
Circular Saw: amzn.to/2ROwDTe
Jigsaw: amzn.to/2VFUiX4
3M Contact Adhesive: amzn.to/2Jqd4vO
Sikaflex 221 Sealant: amzn.to/2vZ7lKn
Rust-Oleum Primer: amzn.to/2Jlb486
Por 15 Top Coat Spray Paint: amzn.to/2wAWZ3H
Reflectix Tape: amzn.to/3dEu3bx
Loctite Construction Adhesive: amzn.to/3awyUti
Foam Brushes: amzn.to/2QYeF06
Simple Green Cleaner: amzn.to/2WylYz2
M8X1.25 screws (for tie down threads): amzn.to/2UZ4RnR
Dewalt Safety Goggles: amzn.to/2xsnNDo
Driver Drill: amzn.to/3ekL2jq
3/4" RMax Polyiso Rigid Foam Board Insulation
1x2’s (primed with rust-oleum mold/mildew prevention primer)
3/4" Birch Plywood
Instagram: / jasonklunk
Epidemic Sound: www.epidemicsound.com/referra...
Tesla Referral: ts.la/jason55632
Main Camera (Sony A7III): amzn.to/36AVy1c
Main Lens (Sony 16-35mm Vario-Tessar T FE F4 ZA OSS): amzn.to/2P4fkeN
Manfrotto Tripod w/ Fluid Video Head: amzn.to/2MLyNjW
Rode VideoMic NTG Shotgun Mic: amzn.to/336tEe7
DJI RSC-2 Gimbal: amzn.to/3vtrEbU
Mavic Air Drone: amzn.to/2EdfGeK
GoPro Hero 7 Black: amzn.to/2GuBFA7
Lighting: amzn.to/2FiksIX
I am available for van build consultation calls if you have questions on your build. Find my email in my bio and send me a message: / @jasonklunk
Music by Qveen Herby - Mint - thmatc.co/?l=7878A1D
As per the Amazon Operating Agreement, I am a participant in the Amazon Services LLC Associates Program. As an Amazon Associate, I earn from qualifying purchases. This is an affiliate advertising program designed to provide a means for this content to earn advertising fees and commissions by linking to Amazon.com and affiliated sites. This is at no cost to you, thanks for your support.
Did you insulate your floor? Would you do it again if you built another van?
I didn't insulate my mini bus floors - just plywood & mold primer. It got cold but not sure it makes a difference if theres no heat source for an extended period of time. Doing a promaster now.. hence why I'm here - It has that heavy duty rubber floor mat 1/4 " thick - tempted to just plywood over that - Happy you insulated?
@@Roam4Wild I found out on accident how much of a difference it makes when I was waiting for things to set, I left a gap in one of my seams and that part of the floor was so much colder than the rest of the floor the next morning. Yes, without a heat source the van is still going to be chilly, but there is a difference IMO. I am happy that I insulated, I would do it again if I built another one.
Great video. Thank you for sharing. I do have a question; I was thinking of using neoprene for my floor insulation ( maybe wrapping it in a plastic?) and then installing those vinyl rectangular- interlocking flooring. I’m wondering if the neoprene will hold over time against mold / moisture Etc.
@@JasonKlunk What do you mean you left a gap?
Good design, thorough work. Everybody, corral your FOAM BOARD SAWDUST to keep it out of streams and oceans.
Great tip! I regretted cutting that stuff outside as soon as I started.
Nice video 👍 so worth doing! Almost miss this stage and we have only just finished ours lol! Nice job 👍
haha thanks!
I didn't realize that 3m 90 worked on foam board. Thanks!
It bonds really well to a lot of different materials. The trick is to spray it on each piece of material, so for example in this case it'd be one side of the polyiso and the van floor, let it sit for like 3-5 minutes until it's tacky, and then adhere them together.
Thanks for the tip for getting the insulation foam board! Got some
In Escondido. I do have few more questions for you. Did you use both birch and poplar furring strips for framing the floor? And was all 1x2 strips? And 3/4 birch plywood for the to lay on top the strips? Lol, thanks again bro I’m sure I’ll be asking more questions. You’re patients and detailed stuff is much appreciated.
Nice, it took me forever to find that stuff. I just used pine 1x2's for the floor, but I primed all of it. Go for the poplar if you're ok with spending the $$. I used 3/4" birch for my subfloor, but you could do 1/2".
Jason Klunk Thanks for all the help 👍🤙
Great videos!
What type of adhesive did you use to glue down your furring strips?
Thanks!
Hey, thanks. I used Loctite Construction Adhesive - there is a link in the description to the exact stuff.
Have you experienced any squeaks with your layout? I"m confuse as how much gap should i leave between the edge and strips? or should i make the strips as close/tight to the edge? any advice truly appreciate. Great video!
That was a concern of mine as well, but I have no squeaks from the floor so far. Give yourself 1/8" - 1/4" for flexing.
Hey Jason how did you find the tie down threads?
Thank you for the video. Did the polyiso create any noise of any kind?
You bet. Nope, my floor is super quiet
Thank you Jason, I am anxious to follow you throughout the build. If you haven't progressed beyond this point yet I was wondering if you could help me with a single measurement. I would really like to know the width of the van measured from outer skin to outer skin (sheet metal to sheet metal) immediately above the upper rails. By "upper" rail I mean the rail that runs the length of the van immediately above the windows/window-areas. Thank you in advance.
sorry for the goofy question but I live on the S. Pacific coast of Costa Rica and getting such measurements for my planning are impossible. thanks again
no worries, I'll try to grab a measurement today
hard to get it accurate because the van curves and I already have insulation in, but it's about 74.5 inches
@@JasonKlunk awesome, thank you for your help.
Where did you use the Sikaflex? I am cutting the plywood tomorrow but wanted to seal things up where needed. Did you use between the joints of 1x2's?
I used the sikaflex to seal up a crack I had in my floor.
Hello hey I like your videos how many pieces did you use going across your floor and the thickness of them, I'm new work on my own van just looking for some help so can give me the measurements of the small pieces
thanks, all those details are in the video
In my opinion the spray on ceramic on the floor and ceiling makes the most sense.
How would you get the spray-on level on the floor?
Cannot find 3/4” polyiso anywhere… already glued my furring strips. I have 1/2 polyiso. Wondering if you suggest me doubling up and pushing the board to be flush with the furring strips? Is that a bad idea? Or maybe using 1/4 havelock wool to make up depth? I am over my head…
Do you have a video of you finishing the floor? I can't seem to find that video in your playlist. I'm referring to your method of either laminate or vinyl flooring. I think you used laminate from some of the clips in your finished van vid. TIA!
Hey, not yet but it's coming. FYI I didn't put down my final flooring until all of my cabinetry was in.
@@JasonKlunk yeah I figured that’s what you did and I’m assuming it was to cut down on costs? No sense in doing the entire floor if you have cabinets that will use that space correct? Also, thank you for taking the time to make this video series. It’s incredible well done and helpful. I just bought a new 2020 transit to convert and I bought all my supplies for the floor based off your vids/ @gregvirgoe . Y’all are hands down the best youtubers when it comes to conveying the build process. So cheers to you again for all the info. 🙏🏽
@@dannysan1272 thank you! Every flooring is different, but if you're using a floating/click-lock vinyl of some sort, in most cases it's recommended by the manufacturer to not install cabinets on top of the flooring.
@@JasonKlunk appreciate that tip; I hadn’t come across that info yet. 🤙🏽
The way of doing things is being organized. No other way.
Keeping everything on paper is the right way..
💯
Do you have a link for the Rattle Trap? Also, how much did you end up getting? Thank you.
I just put it in the description, sorry about that. I bought 50 sq ft.
Will you please tell me where and how much that is sticky insulation can I get it?
Hi Jason...What size bolts did you use to tie your floor down in the existing holes?
They are M8X1.25 - there is a link in the subfloor video if you can't find them. You'll have to figure out the length based on what you are doing for the floor.
@@JasonKlunk Thank you!
How did it turn out function wise? How soundproof is it?
The floor is absolutely solid, I would do the same thing again if I built another van.
What did u do for the front drivers area?
nothing up front
Can you pervide masurment for wood
ProMasters tend to leak ??? Yikes! I did not realize that...
You can find a lot of forum posts about people having water issues. I may have been a bit overzealous with my phrasing of 'tend to leak', but I think it's really important to be cautious of making sure the van is water tight (as best as possible) because of how many other people do have issues.
I personally had issues with the gaskets not sealing on all of my doors so I had water in the van when I first bought it because the dealer power washed the van and didn't realize it was spraying directly inside. I've been paranoid ever since.
What did you use to Glue the 1 by 2 to the floor with ?
Hey, I used some construction adhesive. There is a link in the description to the specific stuff I used.
These videos are great! Thank you for posting.
1X2 wood, with 3/4 inch polyiso, why not 1 inch poly? Is the poly a true 1 inch and the wood not (3/4 perhaps)?
1x2's are 3/4"
@@JasonKlunk figured. Perfect, now I can get rolling. Thanks for your time it is very much appreciated.
When you hear "1 by..." or "2 by...", it's a reference to the nominal lumber size. The actual dimensions of lumber are pretty much never what they're referred to as. A 1x2 is 3/4 x 1-1/2". For any other lumber size, you can look up a nominal vs actual size chart online :)
Hey! Quick question, we also have a Promaster and want to do 3/4 inch polyiso as well, but we’re having trouble finding it! Do you mind if I ask where you found yours??
Oops, never mind, just got to the part of the video where you explain that!
Jesse Larson ha no worries, I had trouble finding it too.
Do you build it as I will.pay for it and how much is it? Your response is highly appreciated. Thank you. 😘
Shoot me an email
@@JasonKlunk hi. The email is xetinetowandoka@gmail.com I and my dad have a plan of having a camper van so we can travel during summer.
Your video showed more of your hair than the point
😂