The nut you tightened on the engine was timing chain tensioner, loosen it up turn it over a few times and it will set the tension itself that knock will go 👌
Not sure if anyone gives a shit but if you are bored like me atm then you can watch pretty much all the new movies and series on InstaFlixxer. Been streaming with my girlfriend these days xD
That nut you tightened adjust the clutch. When you pull up on the shifter it engages the clutch. Be ready for some wheelies too. 225dx is a wheelie machine. You'll love it
My honda always had a tick even after I did adjusted valves. And has full competition bottom end is sound. It's just a three wheeler thing. Great vid bud
I’ve got a 225 dx runs great no matter what sits outside 24/7 always fires up electric start was really slow when I got it put a new starter in it starts lurks dream now
Im restoring a 1982 kawasaki kdx80 i got for free :D im getting no spark but im pretty sure its a stator issue. These videos make me want to get it running so bad.
To change the rear trailing arms, the diff has to come out. At least most of the way out. That intake boot is a huge problem. The maf is the only air metering device on that engine and it needs to have no air leaks between it and the cylinder head.
Really hope you cleaned that inside wheel good or the rust flakes will chew that tube to pieces, also use a round file for valve stem hole if its sharp so it doesn't tear the steam
NEED SOME HELP! I just rebuilt my dirt bike and it now has 5hrs on it. It takes about 20kicks to start it, but soon as it does it runs perfect all the power. Soon as it starts it might die then it will start up again first kick. Not sure what the problem is. I WILL GREATLY APPRECIATE HELP!
Try loosening or tighten the timing chain on the side of the where the cam pulley crank is there's a little screw that looks like a nut on by the BOK you'll see it it's on the right hand side of it
That bolt that says increase and decrease lossen it 3 turns and tighten it back up that's for the chain in the moter that's what the clicking is it's loose and it's slapping around in the moter
That screw is your timing chain adjuster screw start the three wheeler as it’s idling loosen that screw and it will auto adjust then tighten it back down found that out on another RUclips video for you
That battery is one bounce away from disaster. On a lurch to the right, the battery will almost certainly be thrown against the left tire. And there is absolutely nothing providing hold-down force to keep the battery from bouncing up and out past the small lip on the bottom edge of the bracket.
Finally!!! Dalton finished one project 🥳🎉🎊
now that 3 wheeler is what I want for Christmas
The nut you tightened on the engine was timing chain tensioner, loosen it up turn it over a few times and it will set the tension itself that knock will go 👌
I agree that will fix that knock..
Exactly right. 👍. I was going to comment about that but you beat me to the punch. Your genius is showing sir.
Agreed, came here to comment the same.
I give you big time props for keeping track of all these projects.
Nice to see you back to basic repairs enjoying your videos
Best put a rubber grommet in the whole of the frame so it doesn’t cut the wires
U made my Christmas by uploading again
The progress on the new projects is awesome, I really like the content lately and the daily uploads ✔️
Not sure if anyone gives a shit but if you are bored like me atm then you can watch pretty much all the new movies and series on InstaFlixxer. Been streaming with my girlfriend these days xD
@@yahiravery2097 no one does and no one likes spam
Somehow y’all find my comment and a whole bunch of videos and say the same shit
@Yahir Avery yea, been watching on instaflixxer for since november myself =)
@Yahir Avery Yea, been using instaflixxer for since november myself =)
Loving the videos man keep it up! Also love the bmw I remember watching all those videos
30:58 needs a rubber grommet or atleast wrap the wire with more them a few wraps of electrical tape were it goes threw the hole
Damn it’s good to see the old 3dmachines back. These are the videos that built this channel. Cheers mate!
Can you put a rubber grommet in the hole to help prevent the wires from being cut.
I used to have an 85 225DR, those three wheelers are a lot of fun and underrated.
Didn’t know Yamaha made a 3 wheeler. I always thought it was Honda only... that is cool
Out of all the wheelers and dirtbikes I've owned my old 225dx was one of the most fun
Subscribe to this dude he know his stuff!
Put a grommet in that hole, the rought edge will wear through the plastic coating in no time
That nut you tightened adjust the clutch. When you pull up on the shifter it engages the clutch. Be ready for some wheelies too. 225dx is a wheelie machine. You'll love it
That air filter is not pre oiled. It needs to be sprayed with Uni foam filter oil.
Yeah buddy I wanna see some Wheelies
You should do a meetup with Zachgos
For shure Zack goes the s good at wheelies
My honda always had a tick even after I did adjusted valves. And has full competition bottom end is sound. It's just a three wheeler thing. Great vid bud
Leave a👍🏻for 3d machines
Sounds like you need to adjust the valves and I think the knot on the side of the case was for the adjustment on theCentrifugal clutch
I’m livening the old video bring back longer more nitty gritty keep up the good work
Great Video Dalton, great content one on one teaching and fun! thanks for this video!
I’ve got a 225 dx runs great no matter what sits outside 24/7 always fires up electric start was really slow when I got it put a new starter in it starts lurks dream now
Poor BMW is junk, sell it, and with that money finish the Jeep. 🤙🤙
My thoughts to
I agree
No the BMW is og
Both cars should stay the BMW still can be fixed and can be a perfect daily driver some one in his family would really enjoy driving that car
thatdude word
Good job! What does the future hold for the 3 wheeler?
Im restoring a 1982 kawasaki kdx80 i got for free :D im getting no spark but im pretty sure its a stator issue. These videos make me want to get it running so bad.
Sweet.Happy Christmas to you and your's.
These are your best videos dalton little editing and loads of brap
To change the rear trailing arms, the diff has to come out. At least most of the way out. That intake boot is a huge problem. The maf is the only air metering device on that engine and it needs to have no air leaks between it and the cylinder head.
Blow up the BMW on your 100-acre land 🔥🔥🔥 That would be a great video and a lot of views
Jeffrey Matthews no it’s og
No it can be a good car
Jeffrey Matthews that’s a waste lol
BMW = P.O.S
Keep up these type of videos. They are what made me a subscriber. 👍🏻
I want a 3 Wheeler again soooo bad they are a hell of a lot of fun
Another great vid keep it up
Send the BMW to the junkyard 🖖
Cole Miller no
No
BMW is POS
Thats where it came from🤣
Jesse Perry no he bought it
Is that adjustment screw for cam chain tension? Maybe that's causing the noise.
Holy shit I just laughed so hard. Go to 11:13 and watch his mouth on the time lapse part 😂😂😂 gotta have your mouth just right to get that on buddy
Nice truck! Go D-Max
Really hope you cleaned that inside wheel good or the rust flakes will chew that tube to pieces, also use a round file for valve stem hole if its sharp so it doesn't tear the steam
Damn I’ve been subscribed since August 25 2015 🤯🤯😱
The best oil to use for Yamaha is yamalube because I use it on my Yamaha grizzly 660 and it works really good
BMW is rusty af. Dismantle it and sell it in parts
Does anyone notice that the top motor mount is gone?
Yes sir
Love the three wheeler tho I've had many Hondas myself
You should try some amsoil products in the three wheeler for the ticking sound
NEED SOME HELP!
I just rebuilt my dirt bike and it now has 5hrs on it. It takes about 20kicks to start it, but soon as it does it runs perfect all the power. Soon as it starts it might die then it will start up again first kick. Not sure what the problem is.
I WILL GREATLY APPRECIATE HELP!
could be carb related issues, i had a similar issue with a quad bike turns out the carb just needed a rebuild.
check valve clearances.
mmm tea thanks for the help I’ll try that
Banj Fam thanks for the help I’ll try that
Might be a weak spark (plug, coil, gap or ground) all the cranking heats the cylinder enough for a weak spark to finally start
That bmw is clapped man needs a rebuild😂(words from the gasman)
Just needs bilstein suspension
Bye quad ricers nice to meet you
Gonna need a rebuild boys
and a 50k tow job
Try loosening or tighten the timing chain on the side of the where the cam pulley crank is there's a little screw that looks like a nut on by the BOK you'll see it it's on the right hand side of it
What happen to your harbor freight tire changer hitch
Adjust the timing chain tensioner and adjust the valve lash
I believe the advance and decrease on the side of the engine is for timing so you advanced your timing all the way
I’ll take the tbar protecter! I need one
not worried about that hole rubbing those wires through? Gz on getting it running as well!
WHAT KIND OF DRILL BIT DID YOU USE TO DRILL THE HOLE?
31:00 This is a bad move without a rubber grommet
Nice Carolinas boots,I have the same pair lol they can take a beating
That bolt that says increase and decrease lossen it 3 turns and tighten it back up that's for the chain in the moter that's what the clicking is it's loose and it's slapping around in the moter
Just buy a pro taper bar pad for that thing it would look good and they are cheap
That screw is your timing chain adjuster screw start the three wheeler as it’s idling loosen that screw and it will auto adjust then tighten it back down found that out on another RUclips video for you
Whoohooo about time
Get rid of the BMW it's old news finish the jeep build
kiwiflyer new Zealand no the BMW is the best
BMW needs to stay
I agree the bmw is kinda a disappointment
Rather keep the BMW over the jeep
BMW is a pile of shit as soon as he talks about the heap shit I fwd or move onto a new video
when will the 3DMACHINES 2TWO TONE HOODIE in medium be in stock again?
What we have is what we have. Grab a T
3DMachines aawwww okay :(
I have a challenge for you 3dmachines.. This thing runs good by New year's, or it's send off day.. You know Boom!!
Did you bleed the break after putting hand break in
You need a grommet in that hole you drilled because turning is gonna rub threw the wire
Time Table absolutely
Some thin aluminum flat stock should work on making the bottom fender flap stay away from the tire.
To mount and dismount a tire put a some soap water on the bead it will go on alot easier
That battery is one bounce away from disaster. On a lurch to the right, the battery will almost certainly be thrown against the left tire. And there is absolutely nothing providing hold-down force to keep the battery from bouncing up and out past the small lip on the bottom edge of the bracket.
The bar cover matches
Plan on getting the sled out this year ?
Great
I vote Dalton starts a new channel called Parenting with 3DMachines
A yamaha warrior 350 sounds like the yamaha dx 250 did Yamaha use the same 4 Stroke Engine in the yamaha dx 250 and yamaha warrior 350
ah yes, no views, but 25 likes
Your missing the top motor mount don't ride it without it to hard or your chassis is going to snap.
nice vintage rear tire..
Do you live in arkansas
pick up the front end off the trike and slame it down it should make the carb stop leaking
Leave it on gives the bike that special look
Faded teeth protector just needs a light coat of spray paint. Will be way better than no front teeth, even if you leave it as-is!
Pressure wash the frame on 3 wheeler
Oxygen sensor wire of the BMW has a cut in it. Might want to fix that it will start easier.
Omg you got the bmw done good on you man and because I feel bad cause I haven’t watched you in like a year where is the razar
Xavier Draper you mean crush
Think it’s time for car heaven
Get a body kit or something, new custom made exhaust and so interior parts would make the BMW mint
What is the bmw plan.... are you restoring it? Or just blowing it up? I forget
Sending it first class
I've commented on every video about do not paint that blue headlight, nice to see our comments ignored, I even offered to trade you the right one
Gonna guess your not gonna oil that air filter?
Mmupullit got one in on Monday last car row 12
@ 18:50 the 2 nuts u should have said “like a glove “ really dramatic like
Didn't you used to drive a Duramax diesel and a motorcycle?
Woods wagon = BMW
I used to have one of those puppies! They're tippy lol
Damn good job
How are you doing dalton
Sorry Dalton but please dont waste your time with the BMW.. bring it to the trashyard and make a nice Video like Burnout until the engine breaks 😁🙈
Turn the teethsaver insideout and put it on if its possible
Some of the things you say remind me of Mustie1. Is he your dad or uncle?