I love this…. Even though I don’t have any megasquirt products … the software is sick. I use WinOLS… but I’m going to have to do some things with my stock ECU and tune it via stock tables when I turbo my car… but very interesting. I listened to the entire video In essence, we are increasing (scaling) fuel tables… ignition tables, and what else?
Helpful information as usual. Appreciate the insight in the adaptation of a forced induction on an n/a map. This subject isn't covered as well as some people believe. The ignition is a entire separate subject for every type of motor.
I've always used the copy and paste method on the 100 values then highlight and fill column down to bottom row. Then figure the max boost and increase that row by whatever percentage the engine and fuel would demand at that boost level. Then again pull from that value ''whatever it may be'' and down to the 100 row and fill column in that upper section of the table. This has always gotten me in the ballpark quickly and keeps the table smooth. After a little fine tuning, up to target boost i just figure the fuel percentage increase trend and continue that up the graph. Maybe even give it a couple additional points to lean on the side of safety.
Keep going with these videos, they will be very useful when i will have to learn how to boost my fiat panda turbo. Thank you very much. PS what's the deal with monthly subscription?
Thank you :) the monthly membership subscription is RUclips's version of Patreon. It's just to help support content creators beyond watching the videos.
Hy. I really love your videos, gives me courage to start my own MS project. I have a silly question. I want to buy a pre build ms3, but the seller says i dont have to buy a dedicated wb 02 sensor kit with controller, because it already in it. What i need is just the sensor, without controller. Is it possible with ms3?
@@tomisanzero from my experience no megasquirt product comes with a built in wideband controller. You need to buy a controller and sensor like the link I sent and wire it to the O2 input on the megasquirt ECU
starting to tune my boost maps tomorrow and this helped soooo much
Just learning how to tune, these videos are good keep making them please!
Thanks 🙏
Well this one is gonna be super handy. 67 beetle is finally getting an m90 supercharger 🤪 thanks again for this super valuable information
You're welcome! Thanks for watching
I love this…. Even though I don’t have any megasquirt products … the software is sick. I use WinOLS… but I’m going to have to do some things with my stock ECU and tune it via stock tables when I turbo my car… but very interesting. I listened to the entire video
In essence, we are increasing (scaling) fuel tables… ignition tables, and what else?
Helpful information as usual. Appreciate the insight in the adaptation of a forced induction on an n/a map. This subject isn't covered as well as some people believe. The ignition is a entire separate subject for every type of motor.
I've always used the copy and paste method on the 100 values then highlight and fill column down to bottom row. Then figure the max boost and increase that row by whatever percentage the engine and fuel would demand at that boost level. Then again pull from that value ''whatever it may be'' and down to the 100 row and fill column in that upper section of the table. This has always gotten me in the ballpark quickly and keeps the table smooth. After a little fine tuning, up to target boost i just figure the fuel percentage increase trend and continue that up the graph. Maybe even give it a couple additional points to lean on the side of safety.
Good way to go about it
Thank you for the amazing and informative videos. I’m working my way through them all and learning a lot.
You’re welcome! Glad they are helpful!
You're the best, been watching these in preparation of tuning my soon to be boosted E30. Planning to run some high boost, so fingers crossed!
Keep going with these videos, they will be very useful when i will have to learn how to boost my fiat panda turbo. Thank you very much. PS what's the deal with monthly subscription?
Thank you :) the monthly membership subscription is RUclips's version of Patreon. It's just to help support content creators beyond watching the videos.
This guy just have the stuff i need
Thank you for this great info👍
You're welcome!
Got a 95 mustang with a 331 which will get a vortech supercharger soon .
that's soooo interesting !!!! thank u❤
You're welcome! Thanks
Hy. I really love your videos, gives me courage to start my own MS project. I have a silly question. I want to buy a pre build ms3, but the seller says i dont have to buy a dedicated wb 02 sensor kit with controller, because it already in it. What i need is just the sensor, without controller. Is it possible with ms3?
You will just need a controller and sensor kit like this amzn.to/3jaPDfo
@@TurbineResearch so it doesn't matter what he says, i have to buy a full kit with sensor, controller, gauge anyway in order to work with MS3?
@@tomisanzero from my experience no megasquirt product comes with a built in wideband controller. You need to buy a controller and sensor like the link I sent and wire it to the O2 input on the megasquirt ECU
@@TurbineResearch thanks for your help
Can tuner studios work with other ecus? Or just megasquirt?
There are only a couple other that use it like speeduino and rusefi
👍💪