Just got my AWE track exhaust installed. Took about 3 hours. No lift, no Hanger tool. Just jack stands, channel locks and WD-40. Probably could've finished an hour earlier, but each pipe piece had a sticker on it that would only peel off millimeter by mm. Even with goo gone and a razor blade it took a while to get them off. First time I've done an exhaust. But mayn I had the biggest goofiest smile on my face when I heard the cold start. videos don't do it justice, u can feel more rumble. Totally happy with the purchase.
There should be a gap between the flanges at the front pipe due to the donut style gasket that is used. As long as those bolts are tight the gap between those flanges is normal.
Once its installed is it ok if the donut gasket is still partially visible after the spring bolts have been tightened? It looks to me like the gasket is still partially visible, but there is no more threads to tighten down further. Lol
Yes, that is the nature of the the donut. It's very much supposed to be visible once fully tightened (if it wasn't, you'd have a problem). Proceed with confidence! 🤠
@@awetuning If I bring the tips out to show the logo, it doesn’t seem to be secure in place. Do you recommend adjusting the mid pipe to compensate for that? Main concern for all fittings would be to completely block the side cutouts, right? I do want the tips to bring out a bit more. My current fitment isn’t allowing me to do that.
@@TahsinAhmed26 sounds like they need to be tightened further. Use hand tools, and gradually tighten. You’ll find the threshold of where the tip will clamp tightly. Once you find that, adjust once more (you may to loosen slightly to maneuver) and then tighten all the way down once you’re satisfied with placement. Note the install guide and the diagrams showing orientation. Also note, stainless grows in length when hot, so they will protrude out a bit more after reaching operating temps. cdn.shopify.com/s/files/1/0240/7294/5728/files/installation_instructions_awe_Subaru_BRZ_Rev1.2.pdf
At the front of the inlet/ front pipe is that gasket the OEM gasket or is that included with the kit, or sold separately? Just got my gr86 and this is the exhaust I ordered but I want to make sure I have everything I need.
Everything about this exhaust is great except the included hardware for the tips. This is the second one I’ve installed from you guys and it never snugs down. You just have to buy different hardware
Tips don't get as hot as you would think, they are also double walled which helps. We did not see any issues with that in testing or any reports to date.
One in the same. We call our offerings "suites" due to the fact that we offer more than one tip option for each system, and on some vehicles we have a variety of Touring and Track Editions.
We are no longer including them with our kits. If your existing donut is in good shape, use it, if it is not... hit your dealer (or any source for that matter) for P/N 44022AA123
For full details on the AWE Exhaust Suite for the BRZ/86, click here: bit.ly/38XBTzt
Just got my AWE track exhaust installed. Took about 3 hours. No lift, no Hanger tool. Just jack stands, channel locks and WD-40. Probably could've finished an hour earlier, but each pipe piece had a sticker on it that would only peel off millimeter by mm. Even with goo gone and a razor blade it took a while to get them off. First time I've done an exhaust. But mayn I had the biggest goofiest smile on my face when I heard the cold start. videos don't do it justice, u can feel more rumble. Totally happy with the purchase.
Nice work, LB! Happy rippin'.
Just ordered the touring for my 86 :) absolutely can’t wait to install it!
purchased this 2 weeks ago sounds amazing on my 86.
Video made my install go smoothly. Tried it with just a socket wrench and gotta say, just use the impact gun. Exhaust sounds amazing on my 86.
Glad to be of assistance!
Looks great!👍🏼
How much gap is there where the new donut gasket sits? Would love to see a picture of the finished install where the gasket meets the pipe.
There should be a gap between the flanges at the front pipe due to the donut style gasket that is used. As long as those bolts are tight the gap between those flanges is normal.
If the bolts are tight should there still be movement from the donut style gasket?
Thanks for your review and information 👍
Can you tell us what the difference in the volume of the sound compared to the OEM ?
Will be much more volume than OEM especially at startup for the first 30 seconds it is at its loudest.
Once its installed is it ok if the donut gasket is still partially visible after the spring bolts have been tightened? It looks to me like the gasket is still partially visible, but there is no more threads to tighten down further. Lol
Yes, that is the nature of the the donut. It's very much supposed to be visible once fully tightened (if it wasn't, you'd have a problem). Proceed with confidence! 🤠
@@awetuning thanks for the help :)
How do you adjust for the tips? Should they go all in and cover the side cutouts? But that makes the tips way more tucked in than I prefer.
We usally bing them out so the top edge of the logo is showing. Completely your call, though!
@@awetuning If I bring the tips out to show the logo, it doesn’t seem to be secure in place. Do you recommend adjusting the mid pipe to compensate for that? Main concern for all fittings would be to completely block the side cutouts, right? I do want the tips to bring out a bit more. My current fitment isn’t allowing me to do that.
@@TahsinAhmed26 sounds like they need to be tightened further. Use hand tools, and gradually tighten. You’ll find the threshold of where the tip will clamp tightly. Once you find that, adjust once more (you may to loosen slightly to maneuver) and then tighten all the way down once you’re satisfied with placement. Note the install guide and the diagrams showing orientation. Also note, stainless grows in length when hot, so they will protrude out a bit more after reaching operating temps. cdn.shopify.com/s/files/1/0240/7294/5728/files/installation_instructions_awe_Subaru_BRZ_Rev1.2.pdf
At the front of the inlet/ front pipe is that gasket the OEM gasket or is that included with the kit, or sold separately? Just got my gr86 and this is the exhaust I ordered but I want to make sure I have everything I need.
Simply re-use factory. 👍
Just got mine today, it didn’t come with the donut gasket, is it a problem if I use the one that’s already on the car?
We are no longer including them with our kits. If your existing donut is in good shape, yes, if it is not... hit your dealer for P/N 44022AA123
Everything about this exhaust is great except the included hardware for the tips. This is the second one I’ve installed from you guys and it never snugs down. You just have to buy different hardware
Hit us if ya need anything sent over.
Curious to know if the heat from those huge exhaust tips will discolor the rear diffuser?
Tips don't get as hot as you would think, they are also double walled which helps. We did not see any issues with that in testing or any reports to date.
Would this exhaust fit the first gen 86 or only the GR?.
Yes it will fit.
@@awetuning Thank you.
When tightening the spring bolts at the donut gasket, how tight? should the springs be completely compressed?
Yes, the factory nute and bolt should be all the way tight (which is most important). The springs will be nearly fully compressed.
This is the exhaust I plan on getting when my brz gets here in October. Do you have any recommendations on how to install if I do not have a lift?
Certainly achievable with jack and stands. Very straight forward installation.
I just got my exhaust and it didn’t come with the exhaust hanger locking collars
Hey there. Fill this out for us and we can get a set out to ya: awe-tuning.com/pages/support
I ordered track edition on Dec 29, how long does it take to be delivered.
Standard lead time is 3-4 weeks barring any materials delays. Shoot us an email at performance@awe-tuning.com if you need to get in contact with us!
what are the sizes of the hanger collars?
What is the difference between the touring suite and just the Touring?
One in the same. We call our offerings "suites" due to the fact that we offer more than one tip option for each system, and on some vehicles we have a variety of Touring and Track Editions.
Does it fit toyota gt86 2013
Is it possible to buy AWE somewhere in Europe?
Yep! Find 'em here: awe-tuning.com/pages/find-a-dealer
Thanks
Wood smash
LMAOOO
Do you have to use the included gasket for the inlet pipe? I just got mine but the gasket was missing.
We are no longer including them with our kits. If your existing donut is in good shape, use it, if it is not... hit your dealer (or any source for that matter) for P/N 44022AA123
Awesome, thanks for the quick response!
Does it fit toyota gt86 2013
Yep