I've had this exhaust for over a year on my N54, always gets compliments. Only thing I added the next day was a Vibrant resonator where the secondary cats use to be because the drone and rasp sounded like shit lol. You can hear what is sounds like on my dyno run video on my channel. I want to get better sound clips but video doesn't really do it justice.
my dream project, but with a real transmission , 6mt. I have the receiver E91 since 2019, sport + navi + 6mt ; step 1 is done . Trying to find a donor 335 and find time.
@swap depot Check the BOV when the car is idling. you might just have the wrong spring rate if its open during idle you got too soft of a spring. Mine did the same thing on my auto until I changed the spring out.
also for everyone that doesnt want a vrsf exhaust, i have the beluga racing catback and it sounds hottttt. got it for i think 580 after shipping and taxes and its perfect for my upgraded twins.
Please cover what the "DUCK SOUND" is and why it's happening on the car. I have this problem as well and my car is a X drive car so if it's a problem with the way the inlets were installed I will not be happy as it's such a big deal to reach the turbos for any reason on it. But I gotta know why it's doing this. Please! Love the videos!! Thank you! I think it sounds like baby owls or baby seals lol.
please do a VRSF straight pipe with One vibrant resonator, Budget Bimmers was the only one to ever run this setup properly, gotta see it on this sick ass E91
Lol my 148k mile stock turbos with 2in inlets have been doing that stupid duck noise the past 5 years and I thought it was normal (only the noise when you let off). Just heard the last part I missed earlier 🤣 When I put the stock airbox back in the noise goes away so I'm assuming it's because of the inlets. I smoke tested the inlets multiple times in the past and there are no leaks either. I'm also using a tial q bov with 11lbs spring connected to the intake manifold with bigger line so I don't thing it's the bov. If you find any fix for that noise please let us know, it's embarrassing lol.
I have the same sound lol, same bov and same spring. I think its just the way those silicone inlets sound man. My friend has relocated steel inlets and he doesnt have the duck noise
On that Diff ratio you mentioned, if it's a DCT car, swapping diff ratios will trigger issues, but on the auto haven't seen it trigger any faults. I blew my 3.46 stock diff on my e92 n54 6at (the inner housing that holds the spider gears cracked in half), then as an emergency temporary solution, threw in the beefier diff and axles from the 335D e90, the ratio on that is 2.81! Talk about long ass gears! Drove it like that for a week then swapped it back to another 3.46 stock diff. But didn't have any issues... Other than a weird feeling as if I'd lost a gear.. since I'd be driving in 2nd while usually I'd be in 3rd or 4th lol I'd probably swap the 3.15 or 3.07 in it but the 2.81 is waaaay to long of ratio! On DCT cars it uses wheel speed and engine RPM for calculating what gear to be in. But the 6HP has its own speed sensors internally.
I’m surprised you didn’t get the noise after flipping around the center support bearing. From my experience those break easily and eventually wear out the Guibo lol Question: In the long term wouldn’t it create rust if I don’t install the heat shield? I find the driveshaft heat shields so annoying but I always put them back because I’m afraid of rust in the long term …
@@SwapDepot Also I just checked my Center support bearing and mine is installed the way you originally had it. Which is consistent with other Center support bearing replacement videos on RUclips for the 335i . Are you sure that’s the correct way ? Just asking so I can flip mine as well 😂
Have you guys had any experience with Vrsf 1.75” inlets collapsing? I’m getting a noise that sounds like turbo leak, I still need to check the couplers to the intercooler, but I swear I can hear it like it’s coming from the rear turbo inlet. Sounds like it’s right on the other side of the firewall. Will be checking couplers soon to the intercooler but I was just wondering in case it is the inlet. Also the inlet is still on the turbo so it’s not from the snout of the turbo.
@@VehicleVirals want to order them but i move September 10. Will they be here b4 i move? And keep up the great work you’re the reason i have a 335i now!
@@g37xhndrxx54 Hard to promise a date since there's always a slim chance of a shipment delay happening. But assuming they come in on time, you'd receive the downpipes way before your moving day. Appreciate you watching the videos!
I was sitting in a Popeyes drive thru tryna get my pop-on and i swear i thought a marching band was rolling by only to turn and see an Infiniti trumpeting down the road... disgusting
I guess if the person that install it is new to cars and always known it. Jess runs 5.0 especially if no gauge. Yesterday I was beside a charger it sounded good and I'm not a fan on American cars. I let hit cruise at 90+ and hung back and enjoyed the screen. I know a thing or two because I've seen a thing or two. Lol Keep the content coming!
I have a neighbor with a loud car and every time he leave early or late at night. I feel like going out there and break all his window. I don’t see why people do this, inconsiderate bastards. Do they need attention, mommy don’t give them enough attention in their life?
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
You’re a master at your craft brotha. Loving these repair/mod videos. Can’t wait to see what you have planned. Thanks bro
The last 2 clips had me crying that sounds so crazy/interesting, hopefully it’s not some crazy fix! Ali you’re the man
as for the "duck" BOV, get the lightest spring for it, and the vaccum line from the manifold needs to be bigger. :)
I've had this exhaust for over a year on my N54, always gets compliments. Only thing I added the next day was a Vibrant resonator where the secondary cats use to be because the drone and rasp sounded like shit lol. You can hear what is sounds like on my dyno run video on my channel. I want to get better sound clips but video doesn't really do it justice.
It’s a good day when a new swap depot video comes out
Nice.. I'm doing a N54 Awd swap on my e91..
my dream project, but with a real transmission , 6mt. I have the receiver E91 since 2019, sport + navi + 6mt ; step 1 is done . Trying to find a donor 335 and find time.
That elbow dance 🤣🤣🤣🤣🤣
😂
@swap depot Check the BOV when the car is idling. you might just have the wrong spring rate if its open during idle you got too soft of a spring. Mine did the same thing on my auto until I changed the spring out.
Outro clip sounded like I was watching the Jetsons
bruh wagon builds are soo 🔥 there so unique only a handful of them done right on RUclips.... definitely going to be a contender 👍
Ali-Haust is back at it
I’m wondering where’s the shop to visit! Loving the videos and performances 😂
That same sound happened to me when my inlet came off
I threw a e92 m3 factory exhaust on my 335i full catless. Love the way it sounds
I love my Borla catback with my catless downpipes . Secondary cats / mid pipe in place
also for everyone that doesnt want a vrsf exhaust, i have the beluga racing catback and it sounds hottttt. got it for i think 580 after shipping and taxes and its perfect for my upgraded twins.
Please cover what the "DUCK SOUND" is and why it's happening on the car. I have this problem as well and my car is a X drive car so if it's a problem with the way the inlets were installed I will not be happy as it's such a big deal to reach the turbos for any reason on it. But I gotta know why it's doing this. Please! Love the videos!! Thank you! I think it sounds like baby owls or baby seals lol.
Sounds miles better!
Love the sound of the bov. What setup is it?
You guys need to hear an equal length n54 manifold. Its the new must have on n54.
I've found nothing on twins sounds better than PE mod primary catless with secondary cats still in place. Once you go single it sounds better
Nice. Greetings from Mexico
Sounds much much better. Nice homework
forever in the market for an e91
Hard to find good ones
This wagon is going to be 🔥🔥🔥!! Does this VRSF street exhaust fit the E90 Xdrive 335i ?
Sounds good. I like the VRSF race exhaust with vibrant resonators a lil better though
My car makes the same noise. How would I check to see if the inlet is installed wrong?
please do a VRSF straight pipe with One vibrant resonator, Budget Bimmers was the only one to ever run this setup properly, gotta see it on this sick ass E91
He basically has this set up on his e90. Christian does as well on his e90.
@@KAS470 Ye, Christians setup is exactly like BBs. Ali has it too, except with single exit.
That duck noise 😂
Lol my 148k mile stock turbos with 2in inlets have been doing that stupid duck noise the past 5 years and I thought it was normal (only the noise when you let off). Just heard the last part I missed earlier 🤣
When I put the stock airbox back in the noise goes away so I'm assuming it's because of the inlets. I smoke tested the inlets multiple times in the past and there are no leaks either.
I'm also using a tial q bov with 11lbs spring connected to the intake manifold with bigger line so I don't thing it's the bov.
If you find any fix for that noise please let us know, it's embarrassing lol.
I have the same sound lol, same bov and same spring. I think its just the way those silicone inlets sound man. My friend has relocated steel inlets and he doesnt have the duck noise
im having the same sound and can't figure it out at all
@@cptreySounds goes away once I install the stock airbox so it has to be the stock location inlets. I have no leaks at all.
12:19 hittin the woah
Lmao the last clips were funny !!
I think BCBR's ride nice when you also replace all the rubber otherwise Aluminum on Metals of any kind kinda sucks
what’s the setup it had before?
having this same duck noise did you ever figure it out exactly what it is
On that Diff ratio you mentioned, if it's a DCT car, swapping diff ratios will trigger issues, but on the auto haven't seen it trigger any faults. I blew my 3.46 stock diff on my e92 n54 6at (the inner housing that holds the spider gears cracked in half), then as an emergency temporary solution, threw in the beefier diff and axles from the 335D e90, the ratio on that is 2.81! Talk about long ass gears! Drove it like that for a week then swapped it back to another 3.46 stock diff. But didn't have any issues... Other than a weird feeling as if I'd lost a gear.. since I'd be driving in 2nd while usually I'd be in 3rd or 4th lol I'd probably swap the 3.15 or 3.07 in it but the 2.81 is waaaay to long of ratio! On DCT cars it uses wheel speed and engine RPM for calculating what gear to be in. But the 6HP has its own speed sensors internally.
4.10 diff here i come 😂
@@SwapDepot 😂😂 better have some super sticky tires! Traction gonna exit the chat real quick! Especially if you gonna run the FlowMaxes on that e91 😏
Thats the plan! Light up the tires 😂
Enjoyable video - but that drive-by clip sounds so bad haha - keen to see the intake/etc fixed
Can’t wait to see this car de clapped and rippin!
What’s the size an how much for the wheel
What about if your awd I know people that been having issues
You guys are fucking halarious HAHHAHAHAH. Elbow Dance had me dead
my boy needs a head band to keep the sweat off his eyes . sm blinking lolol.
I’m surprised you didn’t get the noise after flipping around the center support bearing. From my experience those break easily and eventually wear out the Guibo lol
Question: In the long term wouldn’t it create rust if I don’t install the heat shield? I find the driveshaft heat shields so annoying but I always put them back because I’m afraid of rust in the long term …
I dont think it would create rust unless you live up north
@@SwapDepot Also I just checked my Center support bearing and mine is installed the way you originally had it. Which is consistent with other Center support bearing replacement videos on RUclips for the 335i . Are you sure that’s the correct way ? Just asking so I can flip mine as well 😂
@@SwapDepot I live in Miami so I’ll toss it 😂
Driveline has to be straight so you dont get any vibration, i would say flip it
Jesssss🔥🔥
Have you guys had any experience with Vrsf 1.75” inlets collapsing? I’m getting a noise that sounds like turbo leak, I still need to check the couplers to the intercooler, but I swear I can hear it like it’s coming from the rear turbo inlet. Sounds like it’s right on the other side of the firewall. Will be checking couplers soon to the intercooler but I was just wondering in case it is the inlet. Also the inlet is still on the turbo so it’s not from the snout of the turbo.
Usually turbo noise is caused by a loose inlet or it popped off
How soon will downpipes get sent out?
On or before August 20th
@@VehicleVirals want to order them but i move September 10. Will they be here b4 i move? And keep up the great work you’re the reason i have a 335i now!
@@g37xhndrxx54 Hard to promise a date since there's always a slim chance of a shipment delay happening. But assuming they come in on time, you'd receive the downpipes way before your moving day. Appreciate you watching the videos!
Those Wheels still for sale??
Yep
So What coil overs do you suggest for e93 335i n55 stage 2+ currently rides shitty
ST coilovers
Sounds like the bov line is disconnected
Nope
@@SwapDepot I got nothin then
auto and manual driveshafts are different
hey I have a e92 335xi is there any VRSF exhaust I can run or no ?
Only thing i can think of is buying the system and modifying mid section to go around the t case
@@SwapDepot word that’s what I was thinking thanks for the advice
what lip did you guys put on this car??
Top secret 😂
@@SwapDepot lol is it the new lip that surfaced on FB forums a few months ago
No this is definitely ebay 😂
@@SwapDepot nothing wrong with that LOL we all know theres a limit to it all haha
Its supercharged 🌝 . i think both exhausts sound pretty good first one sounds more raw
Can you guys help me finding an exhaust for a E60 with a N54 motor
Custom exhaust
That's a Boost leak bro
Would that exhaust fit on a awd e90!?
No rwd only
In Europe we need TÜV!😔
How much for the wheels?
800$
Size of rims and offset .
How much you want for the wheels?
800$
This makes me wanna drop an N54 in my e91 so bad 😭😭😭😭
Do it! 😂
@@SwapDepot you’re the one that made me get the 17t’s from eBay on my n54 e92, I used that same link and they worked amazing 😤🙏
JESS…👌🏻
Fire 🤣
🥺 she sound hurt 😢
Supercharger noises on an N54???? 24:20 HAHAHA
I feel like they were learning how to Weld..period
I was sitting in a Popeyes drive thru tryna get my pop-on and i swear i thought a marching band was rolling by only to turn and see an Infiniti trumpeting down the road... disgusting
please manny swap it
Sounds like a leaky gasket.
Its the inlet
@@SwapDepot The inlet has a leak, installed incorrectly or naturally sounds like that?
Installed wrong
I have the same inlets on my e90 and doesnt sound anything like that
I guess if the person that install it is new to cars and always known it. Jess runs 5.0 especially if no gauge. Yesterday I was beside a charger it sounded good and I'm not a fan on American cars.
I let hit cruise at 90+ and hung back and enjoyed the screen. I know a thing or two because I've seen a thing or two. Lol
Keep the content coming!
I have a neighbor with a loud car and every time he leave early or late at night. I feel like going out there and break all his window. I don’t see why people do this, inconsiderate bastards. Do they need attention, mommy don’t give them enough attention in their life?
Yea ok, dont watch my videos then!
No
Sounds like a diesel LOL
Hey @SwapDepot and @VehicleViral I am not too far from you and would like one of you to look at my 08 e92. How would I get in touch with one of you?
IG swap_depot
@@SwapDepot msg sent