i got a 327 for free because they rebuilt it and left water in it and it cracked it runs hard has a bunch of after market parts on it and chrome but it don't hold water but it don't mix with the oil then i started looking at the block and it is cracked just under the head on the block goes all the way back then down to the oil pan i thinking how does it not mix with the oil but it runs really good and hard . i really only wanted the truck it was in . so i have all the internals for a 327 steel crank heavy rods 12 to 1 pistons moderate cam sounds like a 312 duration about 500 lift . i all ready have 2 327's that are built but will look for another block just i never run a sbc i pull them out and put a bbc in them still have 2 4 inch stroke 450 hp 454 sitting factory built engines
This brings back memories when my brother bought a 307 we couldn't get the engine to crank over turned out one of the Pistons were rusted up in the block the cure to get it to spin over was we're talking junior high here high School I loaded up my wagon with four 12 volt batteries and I hooked them up in series parallel and information it didn't break the ring gear but the engine broke loose and ran one problem it had a miss and a slight lifter sound we thought that was the broken end of the connecting rod on the big end hitting the side of the block noise went away after a little bit but my brother can never get to miss fixed so after compression check he pulls the head off on the side that had the problem turned out that piston wasn't moving up and down with the rest of them on that side of the block again the oil pan comes off he finds out what happened so he pounds out the piston gets a new connection run and voila running on a cylinders amazing what you can do in the backyard as a teenager. Little help from our dad.
This is just a suggestion only but you might consider sparying some PB BLASTER IN each of the Cylinders and let it sit for a couple of days and during that time of settling come buy and spray it a couple of more times. This will help with the tear down of the engine. And who knows you might get lucky and the crankshaft may not be damaged as much as you think. Good luck with your tear down.
They will collapse from sitting oil pressure is critical so if it's not running a long time it's not a spring inside there that keeps it pumped up hydraulic pressure does
should have left the plugs in and you would have seen how everything was positioned ,,,, and how it was burning the feul ... it's the small things you have to look for sometimes !!!!! THOSE ARE GOOD HEAD ON THAT ENGINE .. pull the heads with the plugs in the HEADS...
You don’t need to take rockers loose Take out head bolts and yank off the heads Off course in makes for a longer video People that piddle around to make longer videos about urp me
Never use an impact to remove head studs man that can tell you the tension of each bolt and if there was lots of heat etc in that area… like the sound of music you gotta feel and listen
![Summer Walker - Heart Of A Woman [Official Lyric Video]](http://i.ytimg.com/vi/SFddctbZzw8/mqdefault.jpg)
Dang u lucky .. that 327 came out with a steel crank 💪💪💪💪💪👌👌👌👌😎😎
Nice video ! I enjoyed watching you figure out what went wrong ! Appreciate ya !
same power pack heads that were shared with thr283
Thank you so much for this video bro ! I have a 1966 Chevy caprice with the 327 turbo fire and it’s stuck too…
Thanks for your time.
i got a 327 for free because they rebuilt it and left water in it and it cracked it runs hard has a bunch of after market parts on it and chrome but it don't hold water but it don't mix with the oil then i started looking at the block and it is cracked just under the head on the block goes all the way back then down to the oil pan i thinking how does it not mix with the oil but it runs really good and hard . i really only wanted the truck it was in . so i have all the internals for a 327 steel crank heavy rods 12 to 1 pistons moderate cam sounds like a 312 duration about 500 lift . i all ready have 2 327's that are built but will look for another block just i never run a sbc i pull them out and put a bbc in them still have 2 4 inch stroke 450 hp 454 sitting factory built engines
I’m about to rebuild a 69 327. Thanks for the insight. Keep up the good work
This one has pointe heads(power pack)
There was flat ones, pointe ones, and double hump ones
041 heads I think
Awe the good ‘pyramid’ powerpacs
This brings back memories when my brother bought a 307 we couldn't get the engine to crank over turned out one of the Pistons were rusted up in the block the cure to get it to spin over was we're talking junior high here high School I loaded up my wagon with four 12 volt batteries and I hooked them up in series parallel and information it didn't break the ring gear but the engine broke loose and ran one problem it had a miss and a slight lifter sound we thought that was the broken end of the connecting rod on the big end hitting the side of the block noise went away after a little bit but my brother can never get to miss fixed so after compression check he pulls the head off on the side that had the problem turned out that piston wasn't moving up and down with the rest of them on that side of the block again the oil pan comes off he finds out what happened so he pounds out the piston gets a new connection run and voila running on a cylinders amazing what you can do in the backyard as a teenager. Little help from our dad.
Thanks for sharing and thanks for watching
This is just a suggestion only but you might consider sparying some PB BLASTER IN each of the Cylinders and let it sit for a couple of days and during that time of settling come buy and spray it a couple of more times. This will help with the tear down of the engine. And who knows you might get lucky and the crankshaft may not be damaged as much as you think. Good luck with your tear down.
Man that’s like the engine glad you showed us. You’ll be more educated soon enough
Gr8 engine 2 rebuild...love mine..mi put it in a C10...screamer on RPMsm..💪
Already 💯
great video. subscribed . more 327 videos i hope coming
Gotta throw some new rings in it and hone them cylinders. Too close not to. Cool video, ty
looks like it has 283 power pack heads !
T here is a. Bolt in the center of the big round oil filter canister . 5/8 mayb e
I'm thinking on that 1st side it looks you had a bad head gasket and that's probably why you have rust in the Cylinders.
Put some ATF in the cylinders and let it soak to help loosen it up
A clasped lifter is signs of a oiling problem, maybe a bad oil pump, or they ran it hard low on oil, just thinking out loud
I agree
They will collapse from sitting oil pressure is critical so if it's not running a long time it's not a spring inside there that keeps it pumped up hydraulic pressure does
I look forward to seeing what is behind those heads.
I have this engine in a 1957 Chevy. My dad did it in the late 60s early 70s. It’s has the double hump heads. Should I keep it or LS Swap it?
I’m all about Ls or Lt Gen5 swap. But keep the classic engine.
should have left the plugs in and you would have seen how everything was positioned ,,,, and how it was burning the feul ...
it's the small things you have to look for sometimes !!!!!
THOSE ARE GOOD HEAD ON THAT ENGINE ..
pull the heads with the plugs in the HEADS...
I hear you but remember those plugs was changed after it sat. Meaning the plugs didn’t have any mileage on them
Ther es a bolt , in the center of the oil filter canister ,
Brother I haven't seen so much sludge in an old oil pump on a 327 engine that is
Bad.
me too man lol
I don't think I'd want them guys working on my motor
Let see the motors you work on?
can’t expect to knock a piston thru the bore if it’s connected to crank and rod ? …. wouldn’t even turn a free engine ? …
The reason why I was knocking on them is because I was try to check for Rod bearing play I appreciate the sub homie
Looks like it has forged TRW pistons
I didn’t notice 🤔 that would be cool if it is
You don’t need to take rockers loose
Take out head bolts and yank off the heads
Off course in makes for a longer video
People that piddle around to make longer videos about urp me
I like to get the pushrods out before I pull the heads off thanks though
Yo Mohammed 😂 ❤❤
Your volume is too low
Camshaft junk rock around so loose
Yeah nah
China wall to much silicon.
Wouldn’t it be easier with it on an engine stand?
The engine was locked. And yes
Since the engine was locked he couldn't access all the torque converter bolts to remove it. It's in the way of mounting it on a stand.
283 heads
Open RUclips I like what I like what I see at 3:27 is going to be awesome let's race someday
Fought to pull it up ever thought about tapping it down and then retrying? Bingo
Can't hardly hear you, speak up please
Make sure your volume is up
A
Never use an impact to remove head studs man that can tell you the tension of each bolt and if there was lots of heat etc in that area… like the sound of music you gotta feel and listen