How To Properly Bleed A Master cylinder - FASTEST & EASIEST WAY!!
HTML-код
- Опубликовано: 19 сен 2019
- In this video i show you how to bench bleed a brake master cylinder before you install it. i also show you how to install a master cylinder and properly bleed your whole brake system afterwards.
The syringe tool i used is below:
www.amazon.com/Cardone-10-500...
********Get your klowny1969 Shirts and Apparel here:
teespring.com/stores/klowny1969
video on how to install a vacuum canister:
www.youtube.com/watch?v=v9G0T...
Check out my other videos:
How to change a tire pressure sensor (TPMS) yourself:
www.youtube.com/watch?v=PDpDm...
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
How to Wire A Switched fuse block:
• How To Wire A SWITCHED...
********Get your klowny1969 Shirts and Apparel here:
teespring.com/stores/klowny1969
SUBSCRIBE TO MY CHANNEL! Also check out the videos below!
Complete Brake Overhaul:
www.youtube.com/watch?v=TVA0t...
Vintage air serpentine setup:
www.youtube.com/watch?v=ByVdD...
How to Upgrade your fuel pump:
www.youtube.com/watch?v=8-7sB...
How to install an electric vacuum pump:
www.youtube.com/watch?v=i1n3b...
How to build a camaro from top to bottom:
www.youtube.com/watch?v=5twT_...
400 Cubic inch small block Dyno testing:
www.youtube.com/watch?v=eavm4...
How to Clock an Alternator:
www.youtube.com/watch?v=_I24m...
How to Replace a u-joint:
www.youtube.com/watch?v=QQsXs...
How To install a trans pan drain bolt:
www.youtube.com/watch?v=zXFCB...
How to install subframe connectors:
www.youtube.com/watch?v=9n1Yc...
How to do a quick wheel alignment (toe in toe out):
www.youtube.com/watch?v=Ycdoo...
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world !
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac gmc astrovan truck blazer silverado
Category
Autos & Vehicles 
Авто/Мото
I quickly viewed the video cause i know that some proper pumping was going to happen soon after the sucking. I didn't know you were going to include some plugging and cracking also! Now @ 05:30 i am left without words! I really hope Brianna learned a few tips in this video and as always a great job Klowny!
That squirt was for you ;)
@@klowny1969 Oh my....Brianna gonna be hating!
Great idea!! Definitely saves time and ensures the MC is bled.
thank you..dont forget to subscribe 😉
Great video! Now I am about to do the same to our 1985 motorhome. Thank you so much.
Awesome..dont forget to subscribe
Cool man, I’ve done all new lines up to the MC. Worried about all the flairs I did. I’ll use this for sure when the time comes... 👍
Awesome..good luck
Good Stuff Klowny! Glad I found this video. I really like this method. Thanks for the link too. Cheers from Motown.
thank you sir! don't forget to subscribe and ring that bell!
@@klowny1969
Hello
my car is 1993 Ford Taurus V6 3L and my master cylinder
have 4 ports (4 brake lines) Bendix 12377
its a plastic and there is a filter so its hard to look in
do I do the same things you did with the plastic seringe,,but in my case i need to do the 4 ports instate of 2 like you?
and how long estimate can take
thank you
Nice technique, ill be doing that way from now on
Thank you..it works great!
Very thorough !!!!
Super detailed, Super helpful!!! Thanks a bunch!!🏁🔥🏁🔥
Perfect instructions. 👍👍👍
Thank you..dont forget to subscribe
Best damn video I’ve seen yet on bleeding the master cylinder..👍🏻 damn good job.
Thank you..don't forget to subscribe
Hey man, love the videos. I have a question for you that’s not really part of this video. I have an 85 Camaro. I’ve noticed an rpm surge of about 200 rpm’s when I press the brake pedal, then back to normal, then same surge when I release the pedal. I’ve changed the booster, booster check valve, check filter, and all the rubber hoses that connect those items. Still same issue. Any ideas??
Awesome video thanks I needed this to bleed my brakes on my 68 Chevy
Thanks for watching and don't forget to subscribe
Thanks, was looking for one with the syringe, I was not sure how to use it. hopefully I can get a pedal
afterwards.
Good luck and don't forget to subscribe
@@klowny1969 IT did not work lol no air bubbles when sucking, and none when injecting. The instructions say to inject till no bubbles. 76 C10 truck
Did this today with a food injector , worked well
Thanks for watching and don't forget to subscribe
Hi there , is this master cylinder for 2nd generation camaro.
Very good 😊
Thanks for watching and don't forget to subscribe
Also remember to replace the fluid and bleed at each wheel every 5 yrs. Wheel order, RR, LR, RF, LF. I also bench bleed the master with hoses connected back into the master cyl.
Another great video! I have a question. After doing this process, am I then able to proceed with bleeding each individual line as normal? If I add more fluid to the master cylinder do I need to do the entire process over again?
Yes..I like to start cracking open all the lines from the top and proceed downwards to the rest of the fittings..next would be the fittings on the combo valve..and if ur car has ABS, make sure that system is bled as well..some cars need a computer hooked up to activate the abs solenoids to bleed the air out of there as well..and finally bleed the bleeders at the calipers.
As far as adding fluid..not sure what you are asking me there..just keep the fluid topped off in the master as you are doing this process
@@klowny1969 that answers my question. Thanks much.
Np
Well if you can bleed a master cylinder off the car in this manner,couldn’t you bleed it in this same way on? Thanks for your video it’s very interesting,Lester from Canada
You can..but it would take much longer..don't forget to subscribe
Vacuum bleeder saves the day when bleeding masters
yep..love them
So i got a stumper. 74 f350 disk front drum rear. I replaced the master and booster. Bled the system no air. 18inches of vaccum. I got pedal pressure, no actual brake pressure. Calipers are good but rebuilt anyways. Replaced rear drums, shoes and spring kit. Same thing, plenty of pedal pressure, no grab. Also rear drums are adjusted, even had a mobile brake guy look at it and hes stumped.
The Stutterin Mechanic Sounds like something went wrong with the new booster/brake master installation. The push rod has to be in there correctly and the pedal must not hit any stop. Some cars also have a pressure adjustment valve in the lines that could be set wrong. It is either mechanical with the pedal, or hydraulic in the lines. Good luck.
Are you having no brakes just in the back or just the fronts? If so your valve in your combination valve could have moved. You would have to take the sensor off and use a pick to manually move the valve.I also have a video on how to pressure test your brakes, you can start at the bleeder screws to see the pressures and work your way up to the master..
What is the part number for the syringe?
www.amazon.com/Cardone-10-5000MCB-Master-Cylinder-Bleeder/dp/B002JSM7HA/ref=sr_1_4?dchild=1&keywords=brake+syringe&qid=1633055790&sr=8-4
Dont forget to subscribe
I'm a little surprised that Brianna didn't have anything dirty to say
Bryanna was at time out..caught her doing some unmentionable things the other day...
You can bleed a cervo on the car
You can if you want..this is faster though..dont forget to subscribe
Instruct how much to fill at the end.
Up to the fill mark..don't forget to subscribe
I hope to never need to do this
It's a little messy..but not that bad :)
Be careful not to splooge in her hair, lol.
Yes..that's what I was thinking!!
All that sucking talk..opportunities wasted.
Here we go another autozoner diy guy
Oh did they asked you what color is your car when you asked for the brake fluid ?
Napa auto parts is the way to go
if you think im an autozone diy guy..you havent watched my other videos
@@klowny1969 for sure I haven't watch your videos don't get mad this is youtube