Muy bien, yo creo que también se puede controlar el tiempo de soldadura por un temporizador y un pulsador que uno lo presione en el momento de tener las puntas listas para soldar. Gracias por compartir
Well, brother, if the transfer is set below 18 volts, that is, if you use a transfer of 15 volts or 9 volts, will there be any problem?I used the rest of the equipment given in your video, there will be no problem
Hi Brother I put 4 x 6800 50v capacitors . There is good spark . I used a homemade brass electrode but the electrode itself is getting welded with nickel strip and the two strips is not getting welded at all .please help where the problem is coming.
I don´t know, this is dodgy at best. Just cobble together some crap from the parts bin with no further informaton isn´t gonna cut it for me. I´d like my spot welder with a switch at least...
I am asking just because I have noticed that your welder had a lot of spark. Can I use 12-0-12 and 2 35v 6800uf and kbp307 rectifier with it? What would you suggest?
Iski current kafi ziada thi, spark kafi ziada and cell ki efficiency damage kr skta hy. Me 1 link send kru agr ap usko dekh kr mazeed detail se video banao to wo ap k channel k lye b acha hoga and bananay walay ka fayeda b hojaey ga qk us k current and time ko control kia ja sakta hy.
I use machine for just 1 min. Then my one of the capacitor ( 4700uf 50v ) get explode. When I touch it, it was extremely hot. What's the problem bro ?????
Hello gays! I made this spot welding same from the video but just sparking strong and not welding... Nikel strip make to burn... Output a have 24v DC! I welding with copper elektrode... Can you help me why didn't welding!.? Thanks
Use switch or relay on primary side, first press and hold probes then on switch or relay for less than a second then soot will be neat & clean, i will make video soon
I am using fixed 12 V 6-AMP it has two out put wires, Multimeter is showing 18.36 volts just like the video, I have installed everything according to the manual but spark is very small it's not working I have also attached the button according to your instructions but all in vain it's not welding the nickel strip. Should I use any other capacitor like motor car DC capacitor
@@TARIQLAB One more question please, because I'm a novice. Is it possible to reduce the output voltage with potentiometer, maybe? If yes, how it should be connected?
Hi Bhai saab . i am using a 12v012v 50va transformer . 2x 68000uf 50v capacitors and 6A10 diode bridge . But it is making a good spark but not welding the two pieces. Can you please help what is not working bhai saab
This spot welding project is very useful, great showed, Thank you.
Neat, logical and methodical, a great presentation. Thank you.
It was interesting, but why did you use a rectifier and a capacitor instead of using a transformer alone?
EXCELENTE vídeo. Vou fazer um para mim. Obrigado. Ah! Vc tem algum vídeo ensinando a fazer carregador de bateria?
Capacitor use
nice work and simple
perhaps it is showing >50V output!
let you design one more circuit with minmal p.d, say 3V with lot of current
I m working on that, soon i will upload video
Can I use a 50v 10000uf capacitor?
Muy bien, yo creo que también se puede controlar el tiempo de soldadura por un temporizador y un pulsador que uno lo presione en el momento de tener las puntas listas para soldar.
Gracias por compartir
capasitor cuma 50V di paralel , tengangan outPut 51V . , kalau secara teori capasitornya bisa meledak.
Litar ini adalah untuk 220v, voltan negara saya ialah 240v, jika anda menggunakan voltan 220 atau 230v akan menjadi sekitar 40v
Can i use 12 0 12 4amp transformer with same components
Use spot switch on main ac line
@@TARIQLAB ok but transformer is good for it ?
If guaranteed 4 amp then ok.
Hello bro can we use 27v ac secondary using 63 v 10,000 uf capacitor?
Good
Yes ❤
Maganda yan pero kailangan seconds lang ang pag weld.
If you apply this to a lithium battery, you will throw the battery away. However, it is useful except for the battery and electronics, good job
Current not passes through battery, only one side terminal
Assalaammu'alaikum,brother..
Is it work also for aluminum?
Та херня, видно же в конце видео что дорожка отходит и почему он так хило за полосу держался ? Почему не попытался оторвать ?
Well, brother, if the transfer is set below 18 volts, that is, if you use a transfer of 15 volts or 9 volts, will there be any problem?I used the rest of the equipment given in your video, there will be no problem
Its ok but use higher amp transformer
Good bro
merci , bonne expérience
Did you use one relè ? What is that pop ? You sholud have continous flow of current
Excillent thank you 🙏🙏🙏
Welcome
Hy Brother Can I Use 68000Uf 50 Volt for high Spark Or Other Way to Spot My Project is Not working In Spot Welding
Use on off switch on main side, will work fine
Sir I had made it as you show but the output current you showed 51V in video but my device shows 125V can i use it ?? Its safe??
Too much, not safe
Sir it's burning the nickel strip what can I do to reduce power
Hi Brother I put 4 x 6800 50v capacitors . There is good spark . I used a homemade brass electrode but the electrode itself is getting welded with nickel strip and the two strips is not getting welded at all .please help where the problem is coming.
First press electrodes then on transformer for a short time, u have to use a switch on main side
try to use a harder material for the electrode .... like steel which has a higher melting point
if I add a push button or (switch button), can I use a 3.6 ohm ¼ watt resistor
Why
@@TARIQLAB I mean, I want to add a push button, do I have to use a resistor
Use a push button on main side, that is good for neat spot, no need resistor
@@TARIQLAB Do I need to add an MCB module?
what does push button switch mean?
Can I use 6 amp 4 diodes for bridge rectifier?
Plz reply
Yes
@@TARIQLAB I used but they become hot.
Also it provides high sparking but no welding.
Use 10A diode & use a push button on main side first press probes then press and release button very quickly this will make neat welding without spark
Hi, I have a q, Can i use 12v 10A SMPS? I will connect 2×3300uf 50v capacitors with correct polarity, then connect probes?
Smps will trip,
I don´t know, this is dodgy at best. Just cobble together some crap from the parts bin with no further informaton isn´t gonna cut it for me. I´d like my spot welder with a switch at least...
EXCELENTE...
Wouldn't it be better to use a nail (or other disposable thing) for the positive (in this case) contact probe? Ron W4BIN
hi, but doesn't this soldering method work on a moka? since it's thicker
Nice❤
good
Thanks
RANGKAIAN TERSEBUT APAKAH BISA JADI POWER SUPPLY
Yes
Sir, can I use a tranformer 10a 220v to 18v
Yes
Thank you my friend, may God reward your kindness with heaven
I am asking just because I have noticed that your welder had a lot of spark. Can I use 12-0-12 and 2 35v 6800uf and kbp307 rectifier with it? What would you suggest?
Yes,
sir, can I use 10 a kbpc bridge rectivier 1008
Yes
Sir , I have 2 capacitor of 4700uf , 50 V will it work .....??
Yes
Nickel strip ok but ms strip weld experience????
Pls reply
Bro aap camera close kia kro taa k +ve and -ve terminal nzr to ayn na. Aap ne tips ki wire change kr k konsi Lagai ye b nhi btaya
Pehly wali patli thi moti laga di
Iski current kafi ziada thi, spark kafi ziada and cell ki efficiency damage kr skta hy. Me 1 link send kru agr ap usko dekh kr mazeed detail se video banao to wo ap k channel k lye b acha hoga and bananay walay ka fayeda b hojaey ga qk us k current and time ko control kia ja sakta hy.
@@physicsmentor1984 bhejo link bhai
@@Jdjbsikj ruclips.net/video/BGB8oWpO4pM/видео.html
Bhi yhe transformer kitnay tak ajata
1000 2000 ka
Very powerful 💪💪
Hello, how much amps you have on output, and how it's drop after weld? Voltage after capacitors? Thx
5Amp but capacitor add extra charge to help spot
I use machine for just 1 min. Then my one of the capacitor ( 4700uf 50v ) get explode. When I touch it, it was extremely hot. What's the problem bro ?????
Over voltage or reverse polarity
Terminals(+,-) wrong
could i use 12v 3 amp transformer?
Yes
@@TARIQLAB thank u sir.
what happens when you pull on the strip hard ?
How strong is the weld ?
Eminim oldukça zayıf kaynak
What's the power source? 18V AC?!
Yes, 5A transformer
Capacitor 12volt is it
What are you using for power to the transformer?
AC 220v
hi, transformer AC 8v, ok ?
Hello gays! I made this spot welding same from the video but just sparking strong and not welding... Nikel strip make to burn... Output a have 24v DC! I welding with copper elektrode... Can you help me why didn't welding!.? Thanks
Use switch before transformer, first press electrodes then press and release that switch, this way welding will be neat & clean
Before transformer switcher or after....
Or before rectifier or after.... Where should I put switcher?? Sorry I bother you
Before transformer, on main line
nice
i have tried 15 x 4700uf 35v capacitor in parallel but its not working it puts hole in the strip but not welding it 😔
Add a switch in main side of transformer, first press then on switch for short time it will weld nicely. 4 capacitors enough
Too much currnet (amps), remove some of the capacitors and try again
@@belesman okay i ll surely do
does it not burn the battery structure..
If u want silent spot use switch on main side, first press probes on strip then press and release switch
Can I use 3300uf 35v capacitor.?
Yes
@@TARIQLAB ok
Thanks
Can i this as 110v input ?
sir i tried as per your specfication but cap bursted, solution pl
Use switch or relay on primary side, first press and hold probes then on switch or relay for less than a second then soot will be neat & clean, i will make video soon
thanks sir
I did everything like on video exted i used 3300 and 100v, and i get on output 24v, i dont know why is that? Can u help me?
Transformer volts ?
18v 5a
It's ok i used 18+18 3wire
you shoult show how much
UF /V capacitor.
3300uf 50v
Consegui un transformador de 220v a 25v 2 cables!!
Me sirve los mismos capacitores y puente rectificador para este proyecto ?
Yes
Bos. Kalau Travo CT bisa nggak? Gimana caranya?
Itu trafo ct.. Ct nya gak pk
Will 12 volt Transformer work???
Yes, but not less than 6A
Thanks
Please this transistor is 1/2watts?
No transistor here
Welding nahi pakad rahi
Kya kare
Main pe switch laga len press karny ke baad jhatka den
Video is good but it doesn't work even with 6 Amp transformer 😢
Use switch on main side. First press then press switch less than a second
You mean I should connect the switch at DC side?
I am using fixed 12 V 6-AMP it has two out put wires, Multimeter is showing 18.36 volts just like the video, I have installed everything according to the manual but spark is very small it's not working I have also attached the button according to your instructions but all in vain it's not welding the nickel strip. Should I use any other capacitor like motor car DC capacitor
On AC main side
Replace the secondary wire with thik/multiple good wires together 1/2 round. You will get at least 10amp
Sir capacitor walue bta dein
3300uf 50 volt
@@TARIQLAB super capacitor hein ya normal Jo capacitor
Narmal
18v 5 amp ka transformer lazmi hona chie
12v ka ya 24v ka bhi chaly ga, agar 12v hai tu capacitor ziyada uf ke laga lena
@@TARIQLAB अगर 12 वोल्ट का ट्रांसफार्मर हो तो आपके हिसाब से सर कौनसा कैपेसिटर लगाना सही रहेगा
Hi bro,
Can you make one spot welding for me
Will pay you
Sir can you tell me capacitor value
3300uf 50v
Sir, I have available transformer 220 to 24 volt center-tapped 2A, Can this still work? please reply! Will it work on stainless wire?
yup
I have no centre tapped transformer help me
Use normal 24v but not less than 5Amp, if 12v then 8Amp
@@TARIQLAB I made it the FULKLLL BRIDGEE RECTRRIFAYERR exploded and set my desk alight
whats the minimum amperage of the diodes
What's the minimum amperage of the diodes I used a 2 amps one
it worked 2 times before well
Hi! Can I use a 19V 3.16A laptop charger, instead?
Yes, but use capacitors on 19V line
@@TARIQLAB Thank you for your quick answer!
@@TARIQLAB One more question please, because I'm a novice. Is it possible to reduce the output voltage with potentiometer, maybe? If yes, how it should be connected?
Not possible with potentiometer, potentiometer only 1/4watt.
3300 uf ki jgha 6800 lga sakty hy
good one question can you use a 18v 3a transformer
This is 18v but 18-0-18 used outer wires to make 36v ac, if u have only 18v 2wires then increase capacitors value or number to store more current
@@TARIQLABHow much capacitor would I put? I only have 18 v 3 a
3300uf 50v x2
السلام عليكم سولناك في الوتساب وما جاوبتيناش
Hi Bhai saab . i am using a 12v012v 50va transformer . 2x 68000uf 50v capacitors and 6A10 diode bridge . But it is making a good spark but not welding the two pieces. Can you please help what is not working bhai saab
Use a on off switch in main side, first press spot needles then on for a short time then spot will be fine
Thanks bro will try . is there any need of increasing the number of capacitors
2A keliye Same material lagega.
2amp kam hai
3amp chalega.
Aur capacitor apne Jo use Kiya hai wahi chalega.
10000 uf chly ga
Yes
6v out put is ok for lithium cell 220 to 240 input transfermer please reply
If voltage low amp should be more
@@TARIQLAB a0.65
At 6v u need around 10A
@@TARIQLAB thanks for reply ❤️❤️🤗