Woodworking is quite a difficult job. Building a shed ramp is likewise tough but through this video it is somehow made even easier to follow. I guess this step by step approach can really help to make your shed long lasting.
Thanks so much for a great video. I was able to build my ramp in about an hour and it looks beautiful and doesn't even budge when I drive my lawn tractor into the shed. You rock!!!
Thanks a lot, you have shown me that building a small ramp is a lot easier than i was thinking :D a question though, do you not want a small gap between the treds to allow greater water flow to reduce slipperiness when its wet and getting a bit mouldy?
Thanks for watching, here in Florida I never leave gaps in pressure treated wood outdoors because the climate will do it for you, I used this ramp on my shed and it now has very wide gaps even though I tightened the boards with a ratchet strap. If you are using kiln died wood or you are in a climate where there wont be shrinkage I would definitely leave gaps between the treads. You can also reduce the angle and lengthen the riser to make it safer and easier to use, it just costs a little more
Ted, my shed door extends 1" beyond the door opening. What would be the simplest way to be able to close the door and still have the ramp even with the shed floor? I'm guessing I either have to remove 1" from the door or leave it and mount the ramp one inch lower than the shed floor and have a 1" bump. Also, my shed floor is 17" from the ground. Would it be ok to build the height of the "ground" with concrete pavers as long as it's level, or should I just use wider wood to make the stringers?
Thank you for this video! I was almost going to spend $110 for a kit... I built my shed using a kit but thanks to your video this is very direct and actually simpler than what I thought! You used a 2x12" board for the runners... My ramp only needs to be up to about 7" tall... I feel the 2x12 will be too tall for the ramp any way of modifying it or just cut the board down first then cut the diagnal cut like you did in your first step? Thanks, -Nigel
ACtually you answered my question! 2x10 stringer! Can't wait to do this for a weekend project. Are you using pressure treated wood since it's making contact with the ground? How do you prevent rott? Or is it adviced to paint/stain the wood? Thanks again, -Nigel
Nigel, your welcome, thanks for the positive response. I really enjoy making these videos and it's nice to know people gain confidence from them. Always use pressure treated wood anytime they are to make contact with the ground or are constantly exposed to the elements. Painting and or staining will also help preserve the wood if done properly. Thanks again Ted
![[SFM] Risky Recital](http://i.ytimg.com/vi/RzNkY1_Nk3o/mqdefault.jpg)
Woodworking is quite a difficult job. Building a shed ramp is likewise tough but through this video it is somehow made even easier to follow. I guess this step by step approach can really help to make your shed long lasting.
Thanks so much for a great video. I was able to build my ramp in about an hour and it looks beautiful and doesn't even budge when I drive my lawn tractor into the shed.
You rock!!!
Thanks for a great video. Just built my ramp for my motorcycle and its really sturdy.
Excellent video!!
The treads alone are plenty of bracing it doesn't wobble and screwing it to the shed makes it even stronger
Good project. When your ramp parts were uneven how did you "trim" them?
Thanks a lot, you have shown me that building a small ramp is a lot easier than i was thinking :D a question though, do you not want a small gap between the treds to allow greater water flow to reduce slipperiness when its wet and getting a bit mouldy?
great job explaning i need ramp and i think i can make one thanks
Thanks for watching, here in Florida I never leave gaps in pressure treated wood outdoors because the climate will do it for you, I used this ramp on my shed and it now has very wide gaps even though I tightened the boards with a ratchet strap. If you are using kiln died wood or you are in a climate where there wont be shrinkage I would definitely leave gaps between the treads.
You can also reduce the angle and lengthen the riser to make it safer and easier to use, it just costs a little more
Ted, my shed door extends 1" beyond the door opening. What would be the simplest way to be able to close the door and still have the ramp even with the shed floor? I'm guessing I either have to remove 1" from the door or leave it and mount the ramp one inch lower than the shed floor and have a 1" bump.
Also, my shed floor is 17" from the ground. Would it be ok to build the height of the "ground" with concrete pavers as long as it's level, or should I just use wider wood to make the stringers?
Thank you for this video! I was almost going to spend $110 for a kit... I built my shed using a kit but thanks to your video this is very direct and actually simpler than what I thought!
You used a 2x12" board for the runners... My ramp only needs to be up to about 7" tall... I feel the 2x12 will be too tall for the ramp any way of modifying it or just cut the board down first then cut the diagnal cut like you did in your first step?
Thanks,
-Nigel
ACtually you answered my question! 2x10 stringer! Can't wait to do this for a weekend project.
Are you using pressure treated wood since it's making contact with the ground? How do you prevent rott? Or is it adviced to paint/stain the wood?
Thanks again,
-Nigel
Nigel, your welcome, thanks for the positive response. I really enjoy making these videos and it's nice to know people gain confidence from them. Always use pressure treated wood anytime they are to make contact with the ground or are constantly exposed to the elements. Painting and or staining will also help preserve the wood if done properly.
Thanks again
Ted
nice ramp.
what size screw do you use ?
Good video..
nice
thanks for this
Thanks
Your welcome
I held them together and remarked the uneven part with a magic marker and trimmed one with the skill saw until they matched.