Just built this with my Dad. Thank you so so so so much!!! We had to rewatch the angle part a few times but it was explained so well. Thank you again!!
One of the best instructional videos I've seen for DIY. I plan on building this as a transition incline ramp to eliminate the high step up into our front door. I'll paint it with herculiner truck bed liner to waterproof the wood, and to provide a slip resistant textured surface for walking up the ramp. Thank you sir for helping alot of people remedy a common household problem. Much appreciated.
Glad to hear it was helpful. A truck liner bedding would work really well. It would definitely help waterproof it and make it a little bit more slip resistant
When i tell you THIS VIDEO IS AMAZING! I REALLY MEAN IT! I needed one for my dad; bilateral amputation of both legs, and paralyzed. This video helped me make two ramps. Thank you so much!!
Ramp is amazing! That's awesome that Rex Lumber sent someone out to assist you with the build! The slope on the ramp should be perfect for anyone to go up/down with minimal effort. Nice! *For those that don't know what ripping is: it's going from one side to the other length-wise with your saw to cut down the width to desired size
I need one of those for my house. My father-in-law is wheelchair bound and need this type of ramps. Thanks for the great instructions and showing us how to do it step by step.
It's a good project that should be able to do now that you have seen it done. Be safe, take your time, and get some help to assist your father-in-law out on having a wheelchair ramp at your home. Good luck!
Thanks for the video, it was very helpful. I built a two-piece ramp for my friend based on your design. Her house had two long steps. I built the top ramp so the end of it overlapped the bottom ramp about six inches. The advantage is that the ramps cannot easily separate when she drives her mobility scooter over them While going down the weight of the scooter is already pressing down on the bottom ramp. Anyway, great video, it really helped!
Thank you SO MUCH for an easy to follow video. I was trying to figure out how to calculate the correct angle 📐 of the side support boards and this made it so simple to figure out. Thanks for providing an excellent tutorial! The great thing is it’s easily adaptable to any need.
Just what i was looking for! Retired by Phippeans beach we need side door entrance from kitchen to higher concrete Patio where wife feeds our egg producing Chickens and Ducks.
Tools: * Circular Saw - amzn.to/3eIFC3W * 3/8" Masonry Drill Bit - amzn.to/3eM8Nn2 * T-25 Torx Bit - amzn.to/3bpV6rs * Rigid Hammer Drill - amzn.to/2RgPZ6g * Rigid Drill - amzn.to/3bb9t2S * Square - amzn.to/3vUn4U8 * Tape Measure - amzn.to/3bg83nI * Pencil * Orbital Palm Sander - amzn.to/3fhsBxp * 220 Grit Sandpaper - amzn.to/2RSRHuo * Shop Vac - amzn.to/3ffTmT5 * 4ft Level - amzn.to/3oc9Mjm * Hammer - amzn.to/3tLRVB0 * 3/8 Ratchet - amzn.to/3xWjE5g * 1/2in Socket - amzn.to/3fjRoBd 00:43 The Tools Tools: *Circular Saw - amzn.to/3eIFC3W *Drills - amzn.to/3bb9t2S *T-25 Torx bit - amzn.to/3bpV6rs * 1/8 drill bit - amzn.to/3hlH4v3 * Square - amzn.to/3vUn4U8 * Tape Measure - amzn.to/3bg83nI * Chalk line - amzn.to/2SSUrsx * Pencil * 2in t-25 exterior screws - amzn.to/3fn0TQ6 * 2-1/2in t-25 exterior screws - amzn.to/3ffU5Uj * 3in t-25 exterior Screws - amzn.to/3bp7lEV * Paper - to draw out your design Pressure Treated Wood: * (1) 2 x 6 x 12 * (1) 5/4 x 6 x 8 * (1) 5/4 x 6 x 12 01:27 The Fix - how to measure it all out 04:10 The Header & Rail Cuts 10:02 The Runs Cuts 10:34 Putting It All Together Check out my website at mcfixit.us Disclaimer: Due to factors beyond the control of MC FIX IT, I cannot guarantee against improper use or unauthorized modifications of this information in the video, post, blog, or social media. MC FIX IT assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. If you feel uncomfortable at any time. Stop and go to a professional. MC FIX IT recommends safe practices when working on vehicles, your house, or any other project and or with tools seen or implied in this video. Due to factors beyond the control of MC FIX IT, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MC FIX IT. #mcfixit #wheelchairramp #diy -- Supplies used to record this video: * GoPro Hero 7 Black - amzn.to/3a1uKLU * 256GB Flash Drive - amzn.to/3a1ilre * Vlogging Frame - amzn.to/2Rq7kJL * GoPro Pro 3.5mm Mic Adapter - amzn.to/3s1MNb2 * Youmic Lavalier Lapel Mic - amzn.to/3mB0KeV * Boom Stand - amzn.to/3mCFg1b * 5/8” to 1/4” adapter - amzn.to/3wIJ5Xf
Not quite the way I would have done it. Main issues width, would have gone enough wider to add strips on the sides to make sure the chair wheels could not accidentally go off the sides. Second, I would have overlapped the top by 1/2 width and then sawed off the end with the angle to make the top edge flush with the top of the door step. I don't know if these guys have ever had to move someone in a wheel chair, but the bottom of this ramp is a show stopper. Had they started at the top with a half width, they could have finished on a half width with the last board cut to exceed the end of the ramp risers to give a flush to the concrete edge. What they have instead at the bottom is a one inch wheel stop. The caregiver will have a very hard time getting the chair on the ramp. They will have to first get the front wheels on the ramp by stepping on the wheelie bar(s) and then lifting the entire weight of the chair and patient onto the ramp (no way you will roll the wheels onto the ramp) while controlling the position of the chair on the ramp without going off the sides, a very dangerous situation without guide/guard rails on the edges. Also, looks like they could have gone another foot from the door to reduce the slope. That would be a tough push for anything over a 100# person + chair. I (my own opinion only) would not do this as designed. Could be painted with Non-skid paint (worked well for years on a stair built for an outdoor hot tub.
I just said same thing to my son. Both my kids are in wheelchairs , we have industrial type metal ramps at our house but I'm making one similar to this for my parents house. As well as possibly making one for a person I met yesterday that needs one
Obviously these guys are not so good at building this. But you are going overboard with the difficulty. Also you make it sound like the caregiver is insanely old and needs the chair herself or himself. And did they specify the ramp was for an elderly person with a caregiver? I would assume this kind of ramp would be for a person with a broken leg healing up soon. I hope at least.
This is exactly what I need. Wanting to build a wheelchair ramp for my mother ,as my inaugural project in the workshop that came with my new house, and my dimensions for the door frame and drop are identical to yours.
@@MCFIXIT Havent started yet, been having bad weather. Though, I think I have a problem. The door I'll be putting the ramp at isn't flat to the ground like yours. For some reason, someone has like a concrete glob along that section of the house. I dont know how to explain it.
@@MCFIXIT Ok, I'm getting the materials tomorrow. But I have a question. I got rid of the concrete that was in the way, it wasnt even attached to the foundation, it was just there. But it caused me to miss measure the step, it's 7 inches not 6. Is the best way to adjust the lumber, just to get a x8 piece, and cut off an inch?
13:56 He steps on the ends to make it just like it needs to be. I thought there might be a beveled edge on that last deck board. Probably not really necessary. Nice job.
I would have made it a bit wider to be able to have some extra space on both sides of the door for entering and exiting. Overall a really great video with instructions and tips along the way! Thank you!
I need a ramp like this for my mom. She has an apartment and can't have a fixed ramp. I think my brother will be able to make something like this. I will send this to him!
How did you finish the bottom edge, or did you just pop a small wheelie every time you pushed her up the ramp? Thinking about making something like this for my parents house for when I visit (that they can store in the garage when I'm not there), since they have a ramp up to the porch (concrete, put in when they got their driveway replaced last year) but not from the porch to the door. I would definitely need the bottom edge finished, though, so I'm trying to find a how-to that shows it for a removable ramp like this.
I notice that where the angled framing meets the ledger/ header, they are a bit shorter. is this intentional so that the top 5/4 board pitches downward or should they be flush?
Great informative video making one for my local pub though I will chamfer the last board too make it even easier for the wheelchair , just subbed to your channel , Alan from Scotland cheers
Yes, it definitely should! I have almost the same thing to my shed for my riding mower and I go up and down on it and I’m a big guy. You could always add additional supports under it like 5 instead of 3 boards. Also, you may want to fix it to your house or ground so there no chance of slipping away from the door.
Thanks for the video. Question; Would it be ok to make the ramp wider.... ?? To compensate for ramp movement, since it isn't bolted down and so the the wheel chair doesn't Have to be perfectly centered on it to enter????
for my project I just have to build another step like the one that's existing already there and just build a wider version of the same height and everything and then on the left side it'll have a ramp and a rail to hold on to I'm not sure if I going to put a rail the part that's against the wall maybe not but I am going to put one on one side and then there's going to be another rail going forward so in case somebody wants to walk straight ahead down the stairs they can but for the ramp it's going to be on the side I don't know if my mom will allow me to put the ramp on the side because she has a thing there that shouldn't be there because the ram could go there and that way she has a way to get down without getting hurt
We did not. It's under a covered porch and did not see that necessary since we measured it the way we did. You could if you need to help split the gap on your measurement.
Yes, that is definitely something you could do. I would suggest some 3in Tapcon screws. They often come with a masonry drill bit too. And make sure to pre-drill the wood too! That would definitely make it more secure if you want to go that route. This project was intended to be a simple removal if needed.
Yeah, that’s what I’d do. I would put it into the ground since it’s supposed to be temporary but a few tapcon screws would help hold it in place very well. Then fill the holes with mortar chalk when done using it
I would think that you would want to leave a little gap between the boards for expansion and contraction. Otherwise, a great video. Thanks for posting.
Thank you for the great simple design. I too have stage 4 cancer and need one of these now. The online curb ramps for sale are too steep and expensive and wouldn't work for me. I'm in an apartment with a 5" step up, plus it has to be removable. Since it would be a smaller design, could I use silicone caulking as a temporary hold to the concrete? (So the ramp doesn't slide or someone walks away with it).
Yes, that could be applied to adhere it to the concrete. This could be simply removed when the time to move the ramp. Praying for you and for you to beat cancer! My grandma died of cancer in May and she is the one I built this ramp for.
Are you absolutely positive that it has to be removable? Or are you simply wanting it to be removable in case you want it elsewhere? I'm asking, because there might be some options! First off, the apartment complex - while you would need to talk with them - you should have the right to safely enter the premises, especially if it doesn't cost them anything! Also, are you on any home care? Ask for a social worker. They can help you get resources that you didn't know you qualify for! I wish I could reverse your disease, but hopefully I can at least ease some of the burden!
Are you talking about side by side or two different ones? I don’t see any issue on either of those? If side by side I’d put longer boards on it and make it connected that way.
I have the same step into my house. I also have a 7 inch step from my porch to the sidewalk. Would it be best to keep the platform level until I reach the sidewalk and my 90 degree turn? The sidewalk turns about 15” from the porch. I hope I explained that good.
Yes, that’s what I would do due to how soon it turns. You may want to anchor it to the concrete or to the ground with a pressure treated posts to help it not move though. The benefit of having no turn is the force going up the ramp presses against the step. This would not happen with a turn and some sort of anchoring would help out a lot.
I do need to build one with a 7" header too. Can I used the same proportions to calculate the run, or would you recommend longer? The ramp does not need to be ADA compliant and the shorter the run the better (within reason) as the walkway to the ramp is curved.
Yes, it will be a bit steeper than mine. This one did not also meet ADA standards, but was built for my grandma, who since passed with cancer. This was done to help get in inside and outside of the house for treatments. There was another step shortly after the end of the ramp. You might be able to see it in the video. Once they were no longer needed, we were able to easily remove them. Hope this helps!
I need to build one that would fit onto three stairs so the first step is a really deep step like you stepped on a lot so the previous owner added a box to cut that step in half then there's a half circle brick step and so what I want to do is I want to put a long box that goes from one end to the other and then on the one end on the I want to say if you're facing the door in the inside of the room it would be the one on the left side if you're coming in the room it would be on your right side and build a little ramp that goes down there and I want rails that go down forward and rails that goes sideways so it's like a two-way so you can either go forward and step down the rest of the way or you can turn to your right as you and go down the ramp and that's what I need to build but I'm not sure how it I do that I have a picture of the area but I put it too bad RUclips doesn't have a way to upload pictures so that the RUclipsrs who upload their videos could get a better idea of what we're working with when asking questions
That's hard to picture without a photo or drawing. Ensure there's enough for someone to use the ramp or stairs as needed. Best of luck on your project!
Yes! This is a removable one bc it was on my grandma’s house and she was close to passing and her children were worried about the house selling so they choose to go the route of a removable ramp with it being attached to the house (brick).
That’s definitely an option for you! This was very temporary for my grandma who has since passed. It was also underneath a large covered porch, so the elements really never got to it.
Yes, but it would need to be longer. If you are able, it would be better to Mount this to the ground or house in some way bc of how big it would be. Post holes would be best with a railing since it’s 3 steps.
I do. My Ridgid drill chuck is not the best. It’s a very powerful drill but the chuck sometimes slip and the bit falls out. I’ve contact Ridgid for the repair (free with them) but I’m out of my favorite drill for a few weeks
Yes that’s an option. I’d try to find a treated version if you plan on using it for some time. Plywood can often get damaged easily and weather can become an issue as well. That’s what I used the boards instead of plywood.
Can this be done for a shed? I would like the option to be able to remove it, but need to get my lawnmower up and down with a ramp. Would it withstand weather being treated lumber?
Yes, make sure you only pressure treated lumber to ensure it lasts for a longer period of time. Over time, all wood can deteriorate though, but your best bet is pressure treated.
The top of the ramp should be just below the step not above like in the video because if the person is coming out of the house in a wheelchair, there is a real risk of the ramp sliding out making it useless. You could have fixed it in place with a couple of brackets in to the mortar.
Definitely secure it if in an electric chair, my son was driving his chair down the ramp but I didn't realize he had ran into the railing first and then backed up to go down the ramp. Unfortunately when he hit the railing he moved the ramp out and when the heavy chair started down the ramp it fell and he and his over 800 pound chair fell with it His chair landed on his back and he was using his arms to hold himself up. We have security cameras and when I re watched his fall my heart fell to my stomach. I called the ramp guy at that point t and he came right over to bolt it down He said he didn't realize our son had changed to an electri. Heavier chair. All ramps using wheel chairs should be bolted You can always refill the hole if ramp is no lo gee needed.
Yes, that would be a good drop ratio. This had another step about a foot away from it. So this is what we did to make this temporary wheel chair ramp for grandma before she passed with cancer.
Yes, you could use some sort of deck stain like this: amzn.to/3oBMIv4. They have a variety of tints so make sure it will look good with the decor of your house before purchasing. Ours was a very temporary setup so we did not add a stain to it.
Try and find this answer. Can i build a ramp with a 10"Rise and 60"a run NOT using it for wheelchair access. I keep my motorcycle in my addition 20x20 room and need a ramp just for that on my side entry
Yes, this would be doable. You will need to make it stronger than this video. I would use 2x10 for the joists. 1/2” plywood with joists 12” on center! I would also add some metal structural hardware to give even more strength.
Hi, want to build something similar for our stroller. The design looks solid, just have 1 question - I want to buy pressure treated 2x8, but it is listed as "above the ground". Is there a solution for it? I know that there are U clamps, but I don't want to drill them into the concrete... What would you recommend?
I would go with ground contact treated lumber if you are putting it in the ground. If it's on a porch like this vide, then you are good with above the ground lumber. Does that make sense? Here's a link to Home Depot's pressure treated lumber that's above or below ground: www.homedepot.com/b/Lumber-Composites-Pressure-Treated-Lumber/N-5yc1vZc3sr
I am in a wheelchair, the last board is to high for easy transition going up. It should of had a bevel cut on the last board. If your life revolved around living in a wheelchair , you would know what I am talking about.
Thank you for this tip! I’m sure it will be helpful for others. I bet this would really help out and make the transition easier. This build was a very temporary ramp for my Grandma who has since passed.
We spent about $150. It was a while ago with higher pricing of wood. We had all of the tools and screws. So your cost would depend on those things. You can also build a shopping list at local stores and see exactly how much it would cost in your area.
My first power chair is FWD. I'd have to go up that thing backwards while dragging my foot rests on it, way too short. My next chair is MWD for that reason. never getting FWD again.
Yes the MWD is definitely the best for going up any ramp. This was designed for my grandma with a basic wheel chair in her last days so she could get in and out of her house. There was only enough room to make this length but yes a longer one makes it much easier to go up especially with a powered chair.
Sorry, I do not hire out my work right now. Depends on where you live for how much someone would charge for this project. The cost of labor is crazy high right now.
Looks great but how does someone in a wheelchair reach the door handle and open the door to go through it if they're in their wheelchair on the ramp? Pretty much impossible.
This was built for my grandma in her last days battling cancer so we could get her in and out of her house. It was temporary and removable. Someone was with her to open and close the door for her. If it was a long-term fix, then we would have created a different model for her to able to use the door handle easier.
The "frowning" and "smiling" thing isn't as important as best face up. Besides, its wood. It'll do whatever it wants to, as far as warping in any fashion.
That helps with water run off. Feel free to do best side up. Yeah, warping can be bad depending on how fast the mill dried it and lots of other conditions.
I think I did something wrong because I had a gap and only the point was touching the ground, well I also did not Have enough Height on the 2 x 6 To reach all the way to the floor because of the aggressive angle
Thank you for your comment. You are correct. I mentioned this is ADA approved for sizing. It was completely designed to be temporary and to be removed. It was created for my Grandma who had stage 4 cancer and then quickly passed after it was built. It needed to be temporary and to work with our situation at the time. They have since been removed and the house is about to go up for sale. You could also use this same design for other things like a ramp to a shed to easily get out your mower. Have a great day!
@@MCFIXIT My condolences for your loss. Thanks for the video. I'm looking into buying a home. I'm about at the point with my chronic pain from failed back surgery syndrome and neuropathy to end up in a scooter. This is an excellent solution for a portable ramp where you don't want to permanently modify the property.
Definitely an option! We did this for a temporary ramp before my grandma passed. It’s now in my backyard for my mower to go up and down to our shed. It’s the perfect size for that and when she used it.
Don't see the point of checking if it's square against the door , then pulling it away, cos it then goes off!!, then when pre-drilling give it a wiggle to get it square!!!, oh then step on the bottom to try and square it up !!!., then the drill falls out !!
Thanks for pointing that out. The top is flush with the threshold. The bottom is actually flush at a board width (~3/4in). We didn’t want to cut the board at an angle but leave it the full width to be able the handle the full load of the board since it will have a wheel chair going up and down it. So yes, we did not cut it to be flush and there’s a boards width (~3/4in) but that was planned. It’s hard to say it all in a video and keep it concise enough. Thanks for your comment to allow me to explain that in more detail! Have a great day and thanks for watching & commenting!
Thanks for commenting. I’d say since it’s a tutorial it’s a shorter way of saying “now go ahead and do the step yourself.” Not sure why that’s an issue when you are watching a tutorial on how to do something with multiple steps, can you explain why?
Just built this with my Dad. Thank you so so so so much!!! We had to rewatch the angle part a few times but it was explained so well. Thank you again!!
You are welcome! Glad you were able to complete it together!
One of the best instructional videos I've seen for DIY. I plan on building this as a transition incline ramp to eliminate the high step up into our front door. I'll paint it with herculiner truck bed liner to waterproof the wood, and to provide a slip resistant textured surface for walking up the ramp.
Thank you sir for helping alot of people remedy a common household problem. Much appreciated.
Glad to hear it was helpful. A truck liner bedding would work really well. It would definitely help waterproof it and make it a little bit more slip resistant
When i tell you THIS VIDEO IS AMAZING! I REALLY MEAN IT! I needed one for my dad; bilateral amputation of both legs, and paralyzed. This video helped me make two ramps. Thank you so much!!
Thanks so much for the feedback! This was very helpful for my grandma before she passed.
This is what I needed to help my 94 year old grandma, thank you so much
You are welcome. Hope it helps!
Thank you for this! I don’t have a man at home or a dad and this helped me tremendously!
Glad it was helpful! Good luck on your project
You don't need a man, you just need the proper tools and materials to do the same. You can do it yourself. 👌👍
Ramp is amazing! That's awesome that Rex Lumber sent someone out to assist you with the build! The slope on the ramp should be perfect for anyone to go up/down with minimal effort. Nice!
*For those that don't know what ripping is: it's going from one side to the other length-wise with your saw to cut down the width to desired size
What’s Rex?
@@timbanks4043 They make the lumber from raw logs out of Graceville, Florida and ship the boards nationwide.
Thanks @knightz cross! It has worked very well so far!
I need one of those for my house. My father-in-law is wheelchair bound and need this type of ramps. Thanks for the great instructions and showing us how to do it step by step.
It's a good project that should be able to do now that you have seen it done. Be safe, take your time, and get some help to assist your father-in-law out on having a wheelchair ramp at your home. Good luck!
Thanks for the video, it was very helpful.
I built a two-piece ramp for my friend based on your design. Her house had two long steps. I built the top ramp so the end of it overlapped the bottom ramp about six inches. The advantage is that the ramps cannot easily separate when she drives her mobility scooter over them While going down the weight of the scooter is already pressing down on the bottom ramp. Anyway, great video, it really helped!
Thanks so much! That was nice of you to help your friend. Have a great day!
Thanks for the video! It was super easy, hardest part was making those diagonal cuts by myself.
You are welcome. I hope you get lots of great use of your project!
Thank you SO MUCH for an easy to follow video. I was trying to figure out how to calculate the correct angle 📐 of the side support boards and this made it so simple to figure out. Thanks for providing an excellent tutorial! The great thing is it’s easily adaptable to any need.
Best of luck on your project! Thanks for commenting!
Thank you so much! I'm planning to build a ramp for a friend this weekend and this is exactly what we need!
Glad I could help! Have a great day!
Thanks man! Need this for my elderly Mother.
Glad to help!
Just what i was looking for! Retired by Phippeans beach we need side door entrance from kitchen to higher concrete Patio where wife feeds our egg producing Chickens and Ducks.
That would work!
Tools:
* Circular Saw - amzn.to/3eIFC3W
* 3/8" Masonry Drill Bit - amzn.to/3eM8Nn2
* T-25 Torx Bit - amzn.to/3bpV6rs
* Rigid Hammer Drill - amzn.to/2RgPZ6g
* Rigid Drill - amzn.to/3bb9t2S
* Square - amzn.to/3vUn4U8
* Tape Measure - amzn.to/3bg83nI
* Pencil
* Orbital Palm Sander - amzn.to/3fhsBxp
* 220 Grit Sandpaper - amzn.to/2RSRHuo
* Shop Vac - amzn.to/3ffTmT5
* 4ft Level - amzn.to/3oc9Mjm
* Hammer - amzn.to/3tLRVB0
* 3/8 Ratchet - amzn.to/3xWjE5g
* 1/2in Socket - amzn.to/3fjRoBd
00:43 The Tools
Tools:
*Circular Saw - amzn.to/3eIFC3W
*Drills - amzn.to/3bb9t2S
*T-25 Torx bit - amzn.to/3bpV6rs
* 1/8 drill bit - amzn.to/3hlH4v3
* Square - amzn.to/3vUn4U8
* Tape Measure - amzn.to/3bg83nI
* Chalk line - amzn.to/2SSUrsx
* Pencil
* 2in t-25 exterior screws - amzn.to/3fn0TQ6
* 2-1/2in t-25 exterior screws - amzn.to/3ffU5Uj
* 3in t-25 exterior Screws - amzn.to/3bp7lEV
* Paper - to draw out your design
Pressure Treated Wood:
* (1) 2 x 6 x 12
* (1) 5/4 x 6 x 8
* (1) 5/4 x 6 x 12
01:27 The Fix - how to measure it all out
04:10 The Header & Rail Cuts
10:02 The Runs Cuts
10:34 Putting It All Together
Check out my website at mcfixit.us
Disclaimer:
Due to factors beyond the control of MC FIX IT, I cannot guarantee against improper use or unauthorized modifications of this information in the video, post, blog, or social media. MC FIX IT assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. If you feel uncomfortable at any time. Stop and go to a professional. MC FIX IT recommends safe practices when working on vehicles, your house, or any other project and or with tools seen or implied in this video. Due to factors beyond the control of MC FIX IT, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MC FIX IT.
#mcfixit #wheelchairramp #diy
--
Supplies used to record this video:
* GoPro Hero 7 Black - amzn.to/3a1uKLU
* 256GB Flash Drive - amzn.to/3a1ilre
* Vlogging Frame - amzn.to/2Rq7kJL
* GoPro Pro 3.5mm Mic Adapter - amzn.to/3s1MNb2
* Youmic Lavalier Lapel Mic - amzn.to/3mB0KeV
* Boom Stand - amzn.to/3mCFg1b
* 5/8” to 1/4” adapter - amzn.to/3wIJ5Xf
Not quite the way I would have done it. Main issues width, would have gone enough wider to add strips on the sides to make sure the chair wheels could not accidentally go off the sides. Second, I would have overlapped the top by 1/2 width and then sawed off the end with the angle to make the top edge flush with the top of the door step. I don't know if these guys have ever had to move someone in a wheel chair, but the bottom of this ramp is a show stopper. Had they started at the top with a half width, they could have finished on a half width with the last board cut to exceed the end of the ramp risers to give a flush to the concrete edge. What they have instead at the bottom is a one inch wheel stop. The caregiver will have a very hard time getting the chair on the ramp. They will have to first get the front wheels on the ramp by stepping on the wheelie bar(s) and then lifting the entire weight of the chair and patient onto the ramp (no way you will roll the wheels onto the ramp) while controlling the position of the chair on the ramp without going off the sides, a very dangerous situation without guide/guard rails on the edges. Also, looks like they could have gone another foot from the door to reduce the slope. That would be a tough push for anything over a 100# person + chair. I (my own opinion only) would not do this as designed. Could be painted with Non-skid paint (worked well for years on a stair built for an outdoor hot tub.
Great ideas. Thanks for writing! It worked great as a temporary ramp for my grandma.
I was thinking the same thing about the strips on the sides. That's the way I did my ramp. Best choice I could have done.
I just said same thing to my son. Both my kids are in wheelchairs , we have industrial type metal ramps at our house but I'm making one similar to this for my parents house.
As well as possibly making one for a person I met yesterday that needs one
Obviously these guys are not so good at building this. But you are going overboard with the difficulty. Also you make it sound like the caregiver is insanely old and needs the chair herself or himself. And did they specify the ramp was for an elderly person with a caregiver? I would assume this kind of ramp would be for a person with a broken leg healing up soon. I hope at least.
Yes I agree. How would they get the wheelchair onto the ramp with that gap at bottom???
My son made a ram in the afternoon . I use a walker . It works out fine
That’s great news! Glad it worked out!
Thank you!! My mom and I rent our house so we can't do any remodeling. This is extremely helpful.
You are welcome! Good luck on your project!
This is exactly what I need. Wanting to build a wheelchair ramp for my mother ,as my inaugural project in the workshop that came with my new house, and my dimensions for the door frame and drop are identical to yours.
Glad you found it helpful. How’s the project going?
@@MCFIXIT Havent started yet, been having bad weather. Though, I think I have a problem. The door I'll be putting the ramp at isn't flat to the ground like yours. For some reason, someone has like a concrete glob along that section of the house. I dont know how to explain it.
@@MCFIXIT Ok, I'm getting the materials tomorrow. But I have a question.
I got rid of the concrete that was in the way, it wasnt even attached to the foundation, it was just there. But it caused me to miss measure the step, it's 7 inches not 6. Is the best way to adjust the lumber, just to get a x8 piece, and cut off an inch?
That sounds like it would work. I am a visual person so I’d lay it out and check it before making cuts to ensure it’s exactly what you want
Dude you have nice writing ✍️. It’s almost like a a comic book font 🤙🏼
Thanks!
13:56 He steps on the ends to make it just like it needs to be.
I thought there might be a beveled edge on that last deck board.
Probably not really necessary. Nice job.
Not that I can remember. It holds down fine once the weight of the other boards on placed on top of it.
You just gave me my answer for my New Concrete Up and Down Garage Ramo. Thanks.
Glad it was helpful!
This is the best tutorial so far.
Thank you for putting it together
Thanks so much! I’m trying to make them very user friendly! Make sure to subscribe to see more like this one!
Very good instructional video. The best I have seen. Thank you.
Glad it was helpful!
I would have made it a bit wider to be able to have some extra space on both sides of the door for entering and exiting. Overall a really great video with instructions and tips along the way! Thank you!
You certainly could do that. 36in is half a 6ft board and the width of the door. So that's why we choose to do it that way.
I was thinking the same way. I would make extra 6”. Good video! Thanks!
I need a ramp like this for my mom. She has an apartment and can't have a fixed ramp. I think my brother will be able to make something like this. I will send this to him!
This would be a great option!
How did you finish the bottom edge, or did you just pop a small wheelie every time you pushed her up the ramp? Thinking about making something like this for my parents house for when I visit (that they can store in the garage when I'm not there), since they have a ramp up to the porch (concrete, put in when they got their driveway replaced last year) but not from the porch to the door. I would definitely need the bottom edge finished, though, so I'm trying to find a how-to that shows it for a removable ramp like this.
It didn't need a wheelie, but just a firm push up the ramp. My grandma did not weight much before she passed which probably helped with that.
Building this tomorrow definitely helps a lot
Glad you found it helpful! How’d the project go?
Hello, I’m kind of an idiot, but for the slope of the ramp, did you basically just make a straight line from corner to corner of the board?
I was wondering the same thing.
I notice that where the angled framing meets the ledger/ header, they are a bit shorter. is this intentional so that the top 5/4 board pitches downward or should they be flush?
Great informative video making one for my local pub though I will chamfer the last board too make it even easier for the wheelchair , just subbed to your channel , Alan from Scotland cheers
Glad it helped. That's a great option! Let me know how it goes!
For a 6” rise, the ramp should be 6’ long. I used 1/2” plywood for the top and put 2 x 2 edges to insure the wheelchair doesn’t go off the side.
Those are great tips and would work well. That would not work in this application though. Thanks for adding your comment and watching the video!
Great tutorial! If I wanted to build a ramp flush to the ground, what would I change in this tutorial to do so? Any help would be greatly appreciated!
Use a table saw and cut the angle on the front edge of the ramp
@@MCFIXITI wish I could visualize this fix! And I only have a circular saw. 😢
Question, can I take the full weight of a person on a mobility scooter? If not what adjustments might I have to do?
Yes, it definitely should! I have almost the same thing to my shed for my riding mower and I go up and down on it and I’m a big guy. You could always add additional supports under it like 5 instead of 3 boards. Also, you may want to fix it to your house or ground so there no chance of slipping away from the door.
Great design! This is a super helpful tutorial!
Glad you think so!
Thanks for the video.
Question;
Would it be ok to make the ramp wider.... ?? To compensate for ramp movement, since it isn't bolted down and so the the wheel chair doesn't Have to be perfectly centered on it to enter????
Yes. That would help reduce movement.
Thank you for showing the math
You are welcome!
for my project I just have to build another step like the one that's existing already there and just build a wider version of the same height and everything and then on the left side it'll have a ramp and a rail to hold on to I'm not sure if I going to put a rail the part that's against the wall maybe not but I am going to put one on one side and then there's going to be another rail going forward so in case somebody wants to walk straight ahead down the stairs they can but for the ramp it's going to be on the side I don't know if my mom will allow me to put the ramp on the side because she has a thing there that shouldn't be there because the ram could go there and that way she has a way to get down without getting hurt
Yeah, I'd do whatever is best for you mom! Make sure it's secure and will assist her. I made this for my grandma when her health was failing.
Did you leave a gap in the planking? Or are they butted up against each other. It's kinda hard to tell in the video. Thanks!
We did not. It's under a covered porch and did not see that necessary since we measured it the way we did. You could if you need to help split the gap on your measurement.
@@MCFIXIT Thanks for answering my question!
@@jannetwilson4094 You are welcome! Glad to help!
It looks like you could bolt it down if you really had to though the header and into the brick it really needed!
Yes, that is definitely something you could do. I would suggest some 3in Tapcon screws. They often come with a masonry drill bit too. And make sure to pre-drill the wood too! That would definitely make it more secure if you want to go that route. This project was intended to be a simple removal if needed.
Yeah, that’s what I’d do. I would put it into the ground since it’s supposed to be temporary but a few tapcon screws would help hold it in place very well. Then fill the holes with mortar chalk when done using it
I find this video very helpful… but would you mind if rough estimate how much did you spend in the materials…thanks
It was about $150 but that’s when wood was through the roof. We had all of the tools and screw.
This is Fantastic!! Easy, looks Strong, Great video !!!❤❤❤❤
Thanks so much for watching and commenting!
I would think that you would want to leave a little gap between the boards for expansion and contraction. Otherwise, a great video. Thanks for posting.
Thanks for this suggestion!
Only if the boards are dry.
Glad to find your channel
Thanks! I’m glad you found it too!
Thank you for the great simple design. I too have stage 4 cancer and need one of these now. The online curb ramps for sale are too steep and expensive and wouldn't work for me. I'm in an apartment with a 5" step up, plus it has to be removable. Since it would be a smaller design, could I use silicone caulking as a temporary hold to the concrete? (So the ramp doesn't slide or someone walks away with it).
Yes, that could be applied to adhere it to the concrete. This could be simply removed when the time to move the ramp. Praying for you and for you to beat cancer! My grandma died of cancer in May and she is the one I built this ramp for.
Are you absolutely positive that it has to be removable? Or are you simply wanting it to be removable in case you want it elsewhere?
I'm asking, because there might be some options!
First off, the apartment complex - while you would need to talk with them - you should have the right to safely enter the premises, especially if it doesn't cost them anything!
Also, are you on any home care? Ask for a social worker. They can help you get resources that you didn't know you qualify for!
I wish I could reverse your disease, but hopefully I can at least ease some of the burden!
Really good team work 👍
Thanks so much. I hope it was helpful for you!
Going to build two of these this weekend. I’m worried about the ramp sliding. Any issues with that?
Are you talking about side by side or two different ones? I don’t see any issue on either of those? If side by side I’d put longer boards on it and make it connected that way.
I have the same step into my house. I also have a 7 inch step from my porch to the sidewalk. Would it be best to keep the platform level until I reach the sidewalk and my 90 degree turn? The sidewalk turns about 15” from the porch. I hope I explained that good.
Yes, that’s what I would do due to how soon it turns. You may want to anchor it to the concrete or to the ground with a pressure treated posts to help it not move though. The benefit of having no turn is the force going up the ramp presses against the step. This would not happen with a turn and some sort of anchoring would help out a lot.
I do need to build one with a 7" header too. Can I used the same proportions to calculate the run, or would you recommend longer? The ramp does not need to be ADA compliant and the shorter the run the better (within reason) as the walkway to the ramp is curved.
Yes, it will be a bit steeper than mine. This one did not also meet ADA standards, but was built for my grandma, who since passed with cancer. This was done to help get in inside and outside of the house for treatments. There was another step shortly after the end of the ramp. You might be able to see it in the video. Once they were no longer needed, we were able to easily remove them. Hope this helps!
@@MCFIXIT thank you so much for the video and your response. I'm sorry about your grandma but glad she had someone like you to make things easier.
Quick and easy. Very helpful.
Thanks so much for commenting and watching!
Only easy if you have carpentry skills, difficult for us newbies.
@@outpost31737 I did not have any experience but I did get the help of my neighbor and his mitre saw.
I need to build one that would fit onto three stairs so the first step is a really deep step like you stepped on a lot so the previous owner added a box to cut that step in half then there's a half circle brick step and so what I want to do is I want to put a long box that goes from one end to the other and then on the one end on the I want to say if you're facing the door in the inside of the room it would be the one on the left side if you're coming in the room it would be on your right side and build a little ramp that goes down there and I want rails that go down forward and rails that goes sideways so it's like a two-way so you can either go forward and step down the rest of the way or you can turn to your right as you and go down the ramp and that's what I need to build but I'm not sure how it I do that I have a picture of the area but I put it too bad RUclips doesn't have a way to upload pictures so that the RUclipsrs who upload their videos could get a better idea of what we're working with when asking questions
That's hard to picture without a photo or drawing. Ensure there's enough for someone to use the ramp or stairs as needed. Best of luck on your project!
what great video. thanks !
You are welcome. Thanks for watching
Good one !
You are welcome. Hope it helps!
Would it not be stronger attached to outside?
Yes! This is a removable one bc it was on my grandma’s house and she was close to passing and her children were worried about the house selling so they choose to go the route of a removable ramp with it being attached to the house (brick).
How do you waterproof the ramp so it won't rot?
That’s definitely an option for you! This was very temporary for my grandma who has since passed. It was also underneath a large covered porch, so the elements really never got to it.
we have a 3 step with about 18" height. would it be possible to do the same type of ramp?
Yes, but it would need to be longer. If you are able, it would be better to Mount this to the ground or house in some way bc of how big it would be. Post holes would be best with a railing since it’s 3 steps.
@@MCFIXIT thank you
You are welcome. Have a great day!
You gotta lock those drill bits my guy!
I do. My Ridgid drill chuck is not the best. It’s a very powerful drill but the chuck sometimes slip and the bit falls out. I’ve contact Ridgid for the repair (free with them) but I’m out of my favorite drill for a few weeks
Could you not use a sheet of thick ply wood instead of batons across the frame?
Yes that’s an option. I’d try to find a treated version if you plan on using it for some time. Plywood can often get damaged easily and weather can become an issue as well. That’s what I used the boards instead of plywood.
So really the angled stringers are cut from point to point ( in half) correct??
Yes! If you have enough room on your landing that will work fine!
@@MCFIXIT Yes it worked out great!! Thanks for the video it helped out alot.👍
Can this be done for a shed? I would like the option to be able to remove it, but need to get my lawnmower up and down with a ramp. Would it withstand weather being treated lumber?
Yes, make sure you only pressure treated lumber to ensure it lasts for a longer period of time. Over time, all wood can deteriorate though, but your best bet is pressure treated.
@@MCFIXIT That's really helpful information. Thank you for replying!
@@johnking398 You are welcome. Thanks for watching my video and commenting!
@@MCFIXIT Great tips! Thank you!
Do you do contract work? I need one of these built! I live in Indiana.
I don’t. Thanks for asking though!
@@MCFIXIT I assumed especially since you said you were from Ohio in one of your videos!
The top of the ramp should be just below the step not above like in the video because if the person is coming out of the house in a wheelchair, there is a real risk of the ramp sliding out making it useless. You could have fixed it in place with a couple of brackets in to the mortar.
Don’t ruin a possible AFV entry…….🤪
Definitely secure it if in an electric chair, my son was driving his chair down the ramp but I didn't realize he had ran into the railing first and then backed up to go down the ramp.
Unfortunately when he hit the railing he moved the ramp out and when the heavy chair started down the ramp it fell and he and his over 800 pound chair fell with it
His chair landed on his back and he was using his arms to hold himself up.
We have security cameras and when I re watched his fall my heart fell to my stomach.
I called the ramp guy at that point t and he came right over to bolt it down
He said he didn't realize our son had changed to an electri. Heavier chair.
All ramps using wheel chairs should be bolted
You can always refill the hole if ramp is no lo gee needed.
6” drop recommendation is 72” ramp
Yes, that would be a good drop ratio. This had another step about a foot away from it. So this is what we did to make this temporary wheel chair ramp for grandma before she passed with cancer.
Is there a way to sand the last board down so there's NOT a lift there?
Yes that is def an option!
Great video 👍
Thanks for watching!
Hi, Any suggestions to cover that wood as its getting dirt & the colour is changed.
Yes, you could use some sort of deck stain like this: amzn.to/3oBMIv4. They have a variety of tints so make sure it will look good with the decor of your house before purchasing. Ours was a very temporary setup so we did not add a stain to it.
@@MCFIXIT thanks for your suggestion.
Try and find this answer.
Can i build a ramp with a 10"Rise and 60"a run NOT using it for wheelchair access. I keep my motorcycle in my addition 20x20 room and need a ramp just for that on my side entry
Yes, this would be doable. You will need to make it stronger than this video. I would use 2x10 for the joists. 1/2” plywood with joists 12” on center! I would also add some metal structural hardware to give even more strength.
Excellent video. Thank you!
Thanks so much!
Hi, want to build something similar for our stroller. The design looks solid, just have 1 question - I want to buy pressure treated 2x8, but it is listed as "above the ground". Is there a solution for it? I know that there are U clamps, but I don't want to drill them into the concrete... What would you recommend?
I would go with ground contact treated lumber if you are putting it in the ground. If it's on a porch like this vide, then you are good with above the ground lumber. Does that make sense? Here's a link to Home Depot's pressure treated lumber that's above or below ground:
www.homedepot.com/b/Lumber-Composites-Pressure-Treated-Lumber/N-5yc1vZc3sr
Fantastic! Thank you so much 💪💥😎🙂
Thanks so much!
How to do a much higher ramp? One that leads up to a Mobile Home door.
Much higher and you probably want to secure it to the ground properly with 4x4 posts and concrete:
I am in a wheelchair, the last board is to high for easy transition going up. It should of had a bevel cut on the last board. If your life revolved around living in a wheelchair , you would know what I am talking about.
Thank you for this tip! I’m sure it will be helpful for others. I bet this would really help out and make the transition easier.
This build was a very temporary ramp for my Grandma who has since passed.
how do you get rid of the bump at the bottom
How much was the matirals and how much to build it thk u
We spent about $150. It was a while ago with higher pricing of wood. We had all of the tools and screws. So your cost would depend on those things. You can also build a shopping list at local stores and see exactly how much it would cost in your area.
Definitely needs an aluminum transition at the bottom. A 1” lip is pretty big. Or cut the wood down the last few inches at an angle.
You can definitely do either of those things to ensure a tighter transition. Great ideas!
Thank you!
You are welcome!
Good info, but what weird curved lumber!
Late 2020 lumber… it was all terrible, hard to find, and super expensive!
My first power chair is FWD. I'd have to go up that thing backwards while dragging my foot rests on it, way too short. My next chair is MWD for that reason. never getting FWD again.
Yes the MWD is definitely the best for going up any ramp. This was designed for my grandma with a basic wheel chair in her last days so she could get in and out of her house. There was only enough room to make this length but yes a longer one makes it much easier to go up especially with a powered chair.
Around how much US dollars would you charge to build this?
Sorry, I do not hire out my work right now. Depends on where you live for how much someone would charge for this project. The cost of labor is crazy high right now.
Looks great but how does someone in a wheelchair reach the door handle and open the door to go through it if they're in their wheelchair on the ramp? Pretty much impossible.
This was built for my grandma in her last days battling cancer so we could get her in and out of her house. It was temporary and removable. Someone was with her to open and close the door for her. If it was a long-term fix, then we would have created a different model for her to able to use the door handle easier.
Final someone showed how to make the angle
Glad you found it useful. Thanks for watching and commenting
looks nice.To bad it wont work its still to high at the beginning where the cement and wood meet.
It worked totally fine. No issues at all. We used it for a few months before my grandma passed.
@@MCFIXIT sorry to hear about gramms. My mom's wheelchair is manual and it's pain for every tiny little bump.
My grandma needs one of these for his house. He just got put into a wheelchair and has only been given a few months to live.
Thats almost exactly what this was used for!
If the step is 8" high you must go out 8' that is the ratio...or
6"= 6' and so on.
That’s probably a great plan. For this, there was another step at about 6ft so we choose to go this route. How’d your project turn out?
The "frowning" and "smiling" thing isn't as important as best face up. Besides, its wood. It'll do whatever it wants to, as far as warping in any fashion.
That helps with water run off. Feel free to do best side up. Yeah, warping can be bad depending on how fast the mill dried it and lots of other conditions.
I think I did something wrong because I had a gap and only the point was touching the ground, well I also did not Have enough Height on the 2 x 6 To reach all the way to the floor because of the aggressive angle
But it’s strong enough and it will do the job for a few weeks that I read it
Glad it worked out. Sorry I've been away from my computer recently and just getting back to comments.
🔥🔥🔥
Thanks!
put anti slip tape on top
Great tip! Thanks for adding to the conversation
Ramp must be 6' for ADA unassisted wheelchair.
Thank you for your comment. You are correct. I mentioned this is ADA approved for sizing.
It was completely designed to be temporary and to be removed. It was created for my Grandma who had stage 4 cancer and then quickly passed after it was built. It needed to be temporary and to work with our situation at the time. They have since been removed and the house is about to go up for sale.
You could also use this same design for other things like a ramp to a shed to easily get out your mower.
Have a great day!
@@MCFIXIT My condolences for your loss.
Thanks for the video. I'm looking into buying a home. I'm about at the point with my chronic pain from failed back surgery syndrome and neuropathy to end up in a scooter. This is an excellent solution for a portable ramp where you don't want to permanently modify the property.
I would've built it 4 feet wide. If you were ever in a wheelchair, you'd understand.
Definitely an option! We did this for a temporary ramp before my grandma passed. It’s now in my backyard for my mower to go up and down to our shed. It’s the perfect size for that and when she used it.
Don't see the point of checking if it's square against the door , then pulling it away, cos it then goes off!!, then when pre-drilling give it a wiggle to get it square!!!, oh then step on the bottom to try and square it up !!!., then the drill falls out !!
Flush at the top but no attention paid at the bottom
Thanks for pointing that out. The top is flush with the threshold. The bottom is actually flush at a board width (~3/4in). We didn’t want to cut the board at an angle but leave it the full width to be able the handle the full load of the board since it will have a wheel chair going up and down it. So yes, we did not cut it to be flush and there’s a boards width (~3/4in) but that was planned. It’s hard to say it all in a video and keep it concise enough. Thanks for your comment to allow me to explain that in more detail! Have a great day and thanks for watching & commenting!
Drywall screws? Brudda nooooo
They outdoor torq screws, not drywall screws
MC FIX IT
there is no such thing as 5 1/ 4 board
Good catch. It's 6in, but in reality it's 5 1/2 inches. I miss spoke.
A little too involved for me to follow
Sorry about that. This is a little tougher project than most I do. Hope you have a good day!
Why do Americans say go ahead in every sentence, really unnecessary and I' turn off straight away
Thanks for commenting. I’d say since it’s a tutorial it’s a shorter way of saying “now go ahead and do the step yourself.” Not sure why that’s an issue when you are watching a tutorial on how to do something with multiple steps, can you explain why?
@@MCFIXIT have you counted how many times you said it in that video,it's like torture
No, I haven’t. Sorry it’s torture, but I guess that’s how I talk. Hope you learned something and able to do the project yourself.
"would help if somebody is holding it"
Me- " well mfukka hold it, nikka made me fukk up! ". Lol
Lowlife!
Having extra help always makes projects go smoother. A friendly neighbor is always great to have assist you.