Edelbrock Carburetor Rebuild 83 Regal
HTML-код
- Опубликовано: 7 фев 2022
- In this video I go through the process of removing my 500cfm Edelbrock, part #1404, carburetor and rebuilding it. I also install an electric choke and the powerblast plate from Thompson Performance.
Visit our store below. Thank you for the support!!
stillstandingstore.com/
Instagram👇
/ diaze_stillstanding
Rebuild & Maintenance Kit
amzn.to/34sowVq
Edelbrock 1478 Electric Choke Kit
amzn.to/3gh5Uuc
PowerBlast Plate
thompsonperformance.com/
#83Regal #78MonteCarlo #StillStandingGarage
Edelbrock Carb Rebuild on 83 Regal 
Авто/Мото
Amazing videos! Helped me out a lot
Thank you for watching 👊💯
Thanks for linking this to the Monte--very interesting rebuild. So did you have to replace the fuel pump? Nice job!!
Thank you! I did replace th fuel pump on this motor. Check it out un the Regal's playlist 💪💯
Your videos are dope bro.. keep them coming.
Appreciate it and thank you for watching 👊💯
I appreciate the videos carnal 👌💯 been alot from your vids
I have the same car and engine v6
Most car of tht year have a whole bunch of vacuum lines your engine bay is real nice and clean.
How were you to able make it look like tht
Did you ditch all the vacuum lines? With that set up that you have see you have new intake and carb setup
Because its a hassle trying to route vacuum line and find leaks and try to tune it
Or hopefully you can make a vid of the process of how you did that the pros and cons i guess you can say tht
Because if tht helps the performance in the car, ill ditch all the line amd do the same setup up as you did
Much respect.👍🏾
🤜🤛💯
What performance improvements do you see with your 231, utilizing a 500cfm Edelbrock 4bbl? What Edelbrock intake manifold are you using? I'm restoring an '81 Cutlass with a new 231 engine and 2bbl factory carb. Great videos by the way. Nicely done.
I can feel a bit of improvement in performance. Not enough to do it again on another 231 motor. I have part # 5486 for the manifold. Nice! those factory 2bbl carbs run really nice when they're tuned properly. If I knew what I know now I would of kept my motor all stock. Thank you for watching 👊💯. My apologies on the late reply, I just saw your comment today.
There's only so much you can get out of a 231, less turbo. Mine will be all stock. An LS is way too expensive. I just can't stand all the ridiculous smog control garbage, thanks to the disastrous CAFE standard from the late 70s' early 80's. Sigh... I'm attempting a remedy. @@StillStandingGarage
How’s it going, I have the same engine in my 79 Monte, and 231 V6 3.8L. Can you tell me what intake manifold and Edelbrock Carburetor you have in your regal? Also where did you purchase them? Thanks for your time.
Nice! The manifold is Edelbrock #5486, and the carb is an Edelbrock #1404. I got these from Jegs. I'm not sure if they still have them there. I got mine back in 2005. Thank you for watching 🤝💯
Let's see a new one on the Monte ese
I'm working on it...have a few more on the Regal... I'll probably make an update video on it in between the Regal videos... Thanks for watching 👊💯
@Still Standing Garage Gracias! I have a 79 MC spensa lol
Nice! It's all good 🔥💯
I have a 83 cutlass 3.8 V6. Does the cutlass and regal have the same engine ?
Yes, they share the same engine.
How do you like that intake manifold with no EGR
I like it. It feels like it has a bit more power without it.
cool is the engine a Buick 3.8L V6 can you send the parts #
for that intake manifold and carburetor
Yes, it's a 3.8 V6...the part #s are 5486 for the Intake manifold and 1404 for the carb.
@@StillStandingGarage Thanks Homie
You're welcome💪💯
How do you like that intake and carb on the v6 ? Do you feel any difference ?
Yeah I like it. It runs better than stock. Took a bit of tuning but it runs good now. Working on replacing the fuel pump and adding a fuel pressure gauge and possibly a pressure regulator. Should improve how it runs even more.
I have a 1984 Buick Regal 3.8 V6 231 just like yours. I look up the 1404 Edlebrock Carburetor like yours but it says it is for the 305 V8 engine not the 231 but I am assuming it is because I will have to change the intake manifold is that right? Also do you have the part# for the intake manifold that I need to make mine like yours? Thanks In advance!
Nice! Yes, you'll need the 4bbl manifold to install the Edelbrock #1404 carb. Here's the part number for the manifold...Edelbrock part #5486 💪💯
@@StillStandingGarage thank you Sir, I just followed your Instagram also I have been binge watching your videos all day today! I am changing my window motors on my regal tomorrow I bought the 1 inch hole saw and grinder already thanks to your videos!
That's whats up! Thank you for watching 💪💯... glad my videos are helping