Put your shower on the hottest setting with your exhaust fan off. Give it 5-10 mins to get steamy and apply your protector in there. The steam makes dust particles hard to travel through the air. I've done this for years and it has always worked for me
I just installed one. Here's a small tip to make an easy installation. After setting the screen protector into the small holder, center everything and put a small piece of scotch tape on top of the screen protector (half inch on each side) about half way up the bottom portion, both sides, and stick it to the table. This will hold the screen protector in place. Then you can install the top half without it moving. Remove the tape and install the bottom half. I had a perfect installation. No bubbles, nothing.
This would have been so helpful! I don't think I'll use this type of screen protector again though..but for those who prefer it this way, the tape method sounds like the perfect solution!!
You should try Ringke's s23 accessories, i have the screen protector, magsafe case & camera protector. No hassle while applying the screen protector, and it has a winged design. You should definitely try it out.
I had issues with the middle section picking up dirt before laying it down on the phone. The top and bottom were perfect but the middle sticky section was trapping in dirt creating bubbles. I ruined both unfortunately. The seller reached out after my review and is sending me a replacement. Hopefully I can get it applied correctly with the new kit when it arrives. Nice video!
Thanks Paul! It's a good thing they sent you another one to apply. For me, it's been three months later and the screen protector on the top started peeling off the screen, so I gotta get another one
I installed mine on the first try without any trouble after watching the install video. Not saying if I have to do it again, it will turn out or is it luck.
I’m not sure if they have decent glass screen protectors for the S23 ultra, as it’s got a slight curved screen, but I always use glass screen protectors on my iPhones, as they offer more drop protection, and are way easier to apply, as they are rigid, not all floppy like a plastic one. You demonstrated perfectly in this video, why I hate plastic screen protectors 😂 ok it went on fine eventually, but what a hassle it was! Also I’ve never liked those lens protectors, as they can smudge up, and scratch over time,and hinder the camera performance. I know you’ve used Spigen, and not some cheap ass no name brand, but still, the lens on the phone are way higher quality than any lens protectors, and I’ve yet to damage a lens on my phones, from only using a case, it’s a risk I’m willing take, and I’m careful with my phones😊 Good choice of case though, can’t go wrong with a spigen👍🏻
Yeah I agree, I've always used a glass screen protector for my iPhones but since the s23 ultra has an in screen fingerprint sensor, the glass ones would hinder the sensitivity which I've read has been a problem for those who use the glass ones instead of plastic. And I've never used camera lens protectors before this one so it was kinda a test run for me. Never had an issue with scratching my camera lenses either. Since I won't be buying samsung care for this phone I wanted to protect it as much as I could. And yeah spigens a solid brand!
I have the simtect case for my s23 and it has a sliding door to protect the lens and I also put lens protector over the lens. So the lenses are double protected
When you say "lower sticky part," you're referring to the middle section where I used the squeegee, right? I noticed that as soon as I pulled it. smh... Unfortunately the angle where I was installing it made it difficult to install it properly. You can see in the video when I try to fix it, the phone was off screen. It was easier for me to do it as it was closer to my body. I should've changed the recording angle and installed it from a better position in the first place 🤣
Those lens protectors over the laser mess up focusing in low light. I wouldn't use them. Go out at night and try to take photo. Cant focus. Also with any magsafe accessory attached, s-pen will not work right.
@@MattPau dead spots and erratic behavior when you have an ccessory attached. Doesnt happen if you just have one of those metal magsafe rings on it since those are not magnetic.
@@WarpedTrekker Oh i see. Ok so its not a deal breaker for me since I dont rlly use anything on the magsafe ring except for when im wirelessly charging it.
The camera lens protector barely protrudes from the case so without those protectors, the lenses would either be flush with the case or slightly within the case. Also, the lining on top of the case is slightly thicker so the lenses dont touch the surface if it's laid flat
@@MattPau Thank you so much for your reply. I have a camera lens protector applied and i also bought a spigen case(not the one in your video), the camera protector protrudes that's why im having doubts buying that case on your video. It's not exactly cheap as well but thanks to you, im confident to buy it now. 😊
Hi just wondering does this screen protector work better then the temper glass?? I have been buying the film ones but what if I jump the phone would the film protector help at all???
It sure helps with bumping your phone, I wouldn't say it helps better than tempered tho. Probably the same but for phones with built in finger print readers, go for the filmed ones
First mistake was attempting a screen application without gloves -- always wear gloves. Even washed hands have oils that will transfer to the phone leave finger prints. Watches worker at factories, they always wear gloves. Besides, you can't clean your phone while you're touching it. You also have to squeegee slowly in increments to prevent the bubbles. They certainly don't just "go away." Not completely.
Gloves are definitely not necessary. Never used them and always had no bubbles. They may be helpful but not necessary And actually they did go away completely after 24 hrs
I bought the cryo case from spigen along the most expensive resin screen protector and the lenses protectors and I have to say one thing.... Never again... I put the screen protector perfect and after 45 days bubbles formed out of nowhere in many parts of the screen. Put the lenses protectors and made sure the lenses and Glass was absolutely clean.... Guess what after 2 weeks dust is between lenses and lense protector 😢. As for the case it absolutely does nothing.... I mean it gets a lot of dust between the hexagons.... I'm seriously done with spigen.... Nilkin was always the best.
This screen protector is still bubble free after two months so maybe don't go for the expensive ones cuz this cheap one works just fine! And this case definitely does protect it. But I do see your same issue with the dust accumulating in the holes on the sides of the case.
I agree if you have a thick case or just like me buy Spigen's optic armor case it has a camera slider that you can close when you don't need to use the camera.
I'm not too familiar with greece but I did a quick little search and you can check out this website here: www.skroutz.gr/ Apparently it's the go-to spot for online shopping since there's no Amazon out there.
It slides nicely into your pockets, but I wouldn't say it's slippery by any means. It's not like those cheap plastic cases, and it has a good amount of grip on it when holding it in your hands.
Thanks for the quick response, I have these lens protectors too, I was wondering if when the device is on a flat surface, do the lenses touch it? Or does the case touch?
@@MattPau i mean that was a terrible application of a screen protector all you had to do was press the bubble out and would have been a perfect install
You clearly didn't watch the video then. Bubbles weren't the issue. The screen moved as it was placed the first time. It's just not an ideal method to apply a screen protector but I still wanted to try it out. Never again tho
I swear putting on screen protectors is the most anxious and annoying thing about owning a phone 😂
It really is! 🤣
😁😁😁
Put your shower on the hottest setting with your exhaust fan off. Give it 5-10 mins to get steamy and apply your protector in there.
The steam makes dust particles hard to travel through the air.
I've done this for years and it has always worked for me
The truth my friend is a feeling of nervousness with anxiety 😂😂😂😂😂
@@Jhordan77 facts, i try to do it as slow as possible to minimize mistakes but as you can see through the video, mistakes were still made LOL
I just installed one. Here's a small tip to make an easy installation. After setting the screen protector into the small holder, center everything and put a small piece of scotch tape on top of the screen protector (half inch on each side) about half way up the bottom portion, both sides, and stick it to the table. This will hold the screen protector in place. Then you can install the top half without it moving. Remove the tape and install the bottom half. I had a perfect installation. No bubbles, nothing.
This would have been so helpful! I don't think I'll use this type of screen protector again though..but for those who prefer it this way, the tape method sounds like the perfect solution!!
Bhai samsung s23 ultra pe normal tempered chaadh jata hai naa?? Kyoki kafii loog UV chadhva rahe haii
S23+ flat display and best of both worlds!
You should try Ringke's s23 accessories, i have the screen protector, magsafe case & camera protector. No hassle while applying the screen protector, and it has a winged design. You should definitely try it out.
I had issues with the middle section picking up dirt before laying it down on the phone. The top and bottom were perfect but the middle sticky section was trapping in dirt creating bubbles. I ruined both unfortunately. The seller reached out after my review and is sending me a replacement. Hopefully I can get it applied correctly with the new kit when it arrives. Nice video!
Thanks Paul! It's a good thing they sent you another one to apply. For me, it's been three months later and the screen protector on the top started peeling off the screen, so I gotta get another one
I installed mine on the first try without any trouble after watching the install video. Not saying if I have to do it again, it will turn out or is it luck.
I’m not sure if they have decent glass screen protectors for the S23 ultra, as it’s got a slight curved screen, but I always use glass screen protectors on my iPhones, as they offer more drop protection, and are way easier to apply, as they are rigid, not all floppy like a plastic one. You demonstrated perfectly in this video, why I hate plastic screen protectors 😂 ok it went on fine eventually, but what a hassle it was!
Also I’ve never liked those lens protectors, as they can smudge up, and scratch over time,and hinder the camera performance. I know you’ve used Spigen, and not some cheap ass no name brand, but still, the lens on the phone are way higher quality than any lens protectors, and I’ve yet to damage a lens on my phones, from only using a case, it’s a risk I’m willing take, and I’m careful with my phones😊
Good choice of case though, can’t go wrong with a spigen👍🏻
Yeah I agree, I've always used a glass screen protector for my iPhones but since the s23 ultra has an in screen fingerprint sensor, the glass ones would hinder the sensitivity which I've read has been a problem for those who use the glass ones instead of plastic.
And I've never used camera lens protectors before this one so it was kinda a test run for me. Never had an issue with scratching my camera lenses either. Since I won't be buying samsung care for this phone I wanted to protect it as much as I could.
And yeah spigens a solid brand!
@@MattPau ah I see, you have good reasons for using the plastic screen protector, and lens protectors 👍🏻
Whitestone Dome is the way to go ~
I have the simtect case for my s23 and it has a sliding door to protect the lens and I also put lens protector over the lens. So the lenses are double protected
Nice! Spigen is the Best of the best!
It sure is!
for the screen protector, you have to have the lower sticky part still on the screen. you lifted it all during the installation
When you say "lower sticky part," you're referring to the middle section where I used the squeegee, right? I noticed that as soon as I pulled it. smh...
Unfortunately the angle where I was installing it made it difficult to install it properly. You can see in the video when I try to fix it, the phone was off screen. It was easier for me to do it as it was closer to my body. I should've changed the recording angle and installed it from a better position in the first place 🤣
Elegant looking case
I installed unique me and their lens protectors
Bubbles usually leave within 24 hrs
i just installed perfectely
Bro can ve apply normal screen protector on samsung s23 ultra because alot of people use UV protector for this mobile
I don't see why not
Those lens protectors over the laser mess up focusing in low light. I wouldn't use them. Go out at night and try to take photo. Cant focus. Also with any magsafe accessory attached, s-pen will not work right.
What exactly goes wrong with the s pen? I haven't found any issues at all with it so far
@@MattPau dead spots and erratic behavior when you have an ccessory attached. Doesnt happen if you just have one of those metal magsafe rings on it since those are not magnetic.
@@WarpedTrekker Oh i see. Ok so its not a deal breaker for me since I dont rlly use anything on the magsafe ring except for when im wirelessly charging it.
Funny vid mate! Well done :)
Thanks!! Much appreciated!!! =D
Is that a simple screen guard or a temper glass?
It's not tempered glass.
You put a lot if pressure, is there any chance lenses to crack??
With enough pressure, almost anything can crack. I don't see it cracking from everyday use though
I'm planning to buy that case however I am worried that the camera lens will protrude from the case. Did it though?
The camera lens protector barely protrudes from the case so without those protectors, the lenses would either be flush with the case or slightly within the case.
Also, the lining on top of the case is slightly thicker so the lenses dont touch the surface if it's laid flat
@@MattPau Thank you so much for your reply. I have a camera lens protector applied and i also bought a spigen case(not the one in your video), the camera protector protrudes that's why im having doubts buying that case on your video. It's not exactly cheap as well but thanks to you, im confident to buy it now. 😊
Hi just wondering does this screen protector work better then the temper glass?? I have been buying the film ones but what if I jump the phone would the film protector help at all???
It sure helps with bumping your phone, I wouldn't say it helps better than tempered tho. Probably the same but for phones with built in finger print readers, go for the filmed ones
First mistake was attempting a screen application without gloves -- always wear gloves. Even washed hands have oils that will transfer to the phone leave finger prints. Watches worker at factories, they always wear gloves.
Besides, you can't clean your phone while you're touching it. You also have to squeegee slowly in increments to prevent the bubbles. They certainly don't just "go away." Not completely.
Gloves are definitely not necessary. Never used them and always had no bubbles. They may be helpful but not necessary
And actually they did go away completely after 24 hrs
I bought the cryo case from spigen along the most expensive resin screen protector and the lenses protectors and I have to say one thing.... Never again...
I put the screen protector perfect and after 45 days bubbles formed out of nowhere in many parts of the screen.
Put the lenses protectors and made sure the lenses and Glass was absolutely clean.... Guess what after 2 weeks dust is between lenses and lense protector 😢.
As for the case it absolutely does nothing.... I mean it gets a lot of dust between the hexagons....
I'm seriously done with spigen.... Nilkin was always the best.
This screen protector is still bubble free after two months so maybe don't go for the expensive ones cuz this cheap one works just fine!
And this case definitely does protect it. But I do see your same issue with the dust accumulating in the holes on the sides of the case.
Yes, I like Nillkin products too.
does any spigen case fit with the camera spigen lens protector?
Not too familar with their other cases. I’m guessing they would but always double check from their website
Good video bro!
Thanks !! I appreciate it!! 💯
Screen protector , is it.covering full screen
Not 100%
I bought new s23 ultra yesterday do I need camera lens protector
I feel like if you grabbed a good case you wouldn't need it but if you want some peace of mind I wouldn't hesitate to put one on
no
@@WarpedTrekker thank you bro 😊
I agree if you have a thick case or just like me buy Spigen's optic armor case it has a camera slider that you can close when you don't need to use the camera.
I've smashed many screens and backs in my time, but never have I cracked the camera lens
hey there i cant find this screen protector anywhere, i only get neofilm from spigen which is not as good any help ? i m in greece btw :')
I'm not too familiar with greece but I did a quick little search and you can check out this website here: www.skroutz.gr/
Apparently it's the go-to spot for online shopping since there's no Amazon out there.
Does the case feel slippery?
It slides nicely into your pockets, but I wouldn't say it's slippery by any means. It's not like those cheap plastic cases, and it has a good amount of grip on it when holding it in your hands.
Doesn't the case lift the protector screen?
Not at all! I was afraid of this happening but it didn't lift it at all!
Beautiful phone 📱
I love this phone!
13:40
Nice room man
Tyty! I wanna do a room tour but it's not done just yet! Soon though!
Does the case cover the lens?
The case goes around the lenses which is why I added those camera lens protectors!
Thanks for the quick response, I have these lens protectors too, I was wondering if when the device is on a flat surface, do the lenses touch it? Or does the case touch?
No prob! And the case is ever so slightly thicker on the top so the case touches the surface.
4:15
sheesh that hurts to even watch
Never stressed that much over a simple screen protector installation hahaa
Who told u to make video
No one! I always buy a lot so why not record it and post?
@@MattPau i mean that was a terrible application of a screen protector all you had to do was press the bubble out and would have been a perfect install
You clearly didn't watch the video then. Bubbles weren't the issue. The screen moved as it was placed the first time. It's just not an ideal method to apply a screen protector but I still wanted to try it out. Never again tho
What's the point of the video ? you did everything off camera
Only when I was trying to fix the screen protector for like 20 seconds but other than that everything was on camera.
Agbagadc
Estas bien panque
Muy bien panque
Pésimo
Muy pésimo
@@MattPau 😲
you lack technical skills 🤣😂
LOL tell me about it
Dude, you wasted my time
Sorry to hear that 😞 Check out the timecodes to save some time
not so intelligent . but still .............
I'm glad you took the time to comment and let me know! I appreciate ya!! 😊
Why it's an RUclips video 🤢
Why not?? 😆
@@MattPauI don't understand either, Instagram user 99%