Hello Freddy, I have always flown the ar7200bx and know it so well by now that I hardly need the set up manual anymore. I just bought a used 700 DFC with a 3gx. I watched some other set up videos and was intimidated by how complicated the programming seemed. I found your series on the 3gx and with your help I was able to get set up on the first try. I just wanted to thank you for a really great and easy to follow instructional. Keep it up!
This might be an older video, but its priceless to someone like me that JUST picked up an Align Pro, completely built and ready to go but I have no info on it. I was told it was hoovered twice and put away. no crashes. It has many upgraded parts as well as all the upgrades. It is NOT flybarless. I may convert it to flybarless but need someone that knows this stuff better than myself.
Incredibly helpful!! I ordered an align 3gx earlier today for a mini Titan e325. I was a little worried that the 3gx would not be as easy to setup as my beastx. Your videos make it look simple!! Thank you
man i just set up a 3gx with satellite for the first time couldn't figure out why the tail wasn't working after about 30 mins i remembered this video ..for got to set gyro sw to aux 2 ..so glad you made this vid
Thanks for doing this set of videos. I've been struggling to understand how to setup a Trex 500 with a 3GX and nothing I've found elsewhere has come as close as your vids to explaining clearly the steps required.
thanks for replying and greetings from australia.in the manual it goes further with 3gx thottle calibration-flight mode setting-ail roll rate-elev end point setting-ail end point setting-swash dampening setting-swash accelerate setting- Do you need to do any of this??? Iam into sports flying.i appreciate all your hellp and your willingness to share your knowledge.cheers mate,mark
Freddy can you tell me how to wire the 3GX, AR8000 receiver and the BEC? I watched your setting up throttle and pitch curves videos. i have a DX7S, according to your video I should make the Normal mode throttle curve as in your video right? throttle menu has N,I,H. What is the 3D mode? is it I or H? for 3D mode I should change my curves look like your drawings right? I couldn't find a video of showing the setting up a radio. Thank you
Great video. Clear, concise, and very informative. I just put together a 550e and I'm trying to set up the 3GX. The problem is that even when I'm in DIR mode, when I raise the throttle the motor spools up. I have no idea why, any ideas? I have a separate BEC which is supplying power to to the 3GX, but when I remove the ESC to try to do it that way, I get an error on the 3GX and can't do anything. Any suggestions?
Excellent set of videos. One question is on the 3GX manual it says near the beginning to turn off the Swash mix Function. I don't understand why you would do this and you didn't on your video.
i have watched all 4 parts plus your 2 gyro vids and i have to say they are the best for helpful and valuable setup information that no instruction manual has got.i have just built a trex700E DFC together with dx8 .Please answer this,with the 3GX ,during the setup of the swash endpoint sequence the swash responds in the tests easy to see,but after initialization is complete and the swash jumps up 3x the helis swash doesnt respond with as much movement as in previous tests in setup mode,is ok??
Great video series Freddy - Top Man - Could not have completed the set up of my Align 500 without them. One question - I am using a DX6i radio and cannot find the SW Select option on my radio to set my giro to Aux2. Can you help ??
First, thanks for the great videos. I'm trying to set up a Trex550E with the 3GX & would be completely lost without your series of video guides. As it is, I can't get the correct operation of the pitch servo in cyclic unless I connect it to the throttle connection on the 3GX. This obviously can't be right, but I've checked & tried everything else. The set up is a Futaba T8FG Tx with a Futaba R617FS Rx.. Any ideas Freddie? Many thanks
thank you - we are trying your suggestions - we added another bearing to torque tube and replaced the gray with red on head - I do sport flying -will let you know
hi, so is it normal for a servo to go back to center slowly when i use aileron or elevator? i thought it suppose to respone fast like in your video. the servos move fast back up when its in DIR mode but not when its normal mode.
Yes in the setup modes the Gyros are not active so they are not looking to counter balance so the servos will act as if there is no gyro. Once programming is exited the gyros are active, and if the Heli is just sitting there they seem to behave oddly because they are following the programming and waiting for the Heli to move so it can correct it.
Hi Freddie, To save you time, ignore my previous question regarding the Pitch servo cyclic response. I've just been told that the Trex550E-3GX manual 3GX wiring instructions are wrong, at least for Futaba Rxs! (see page 17 The yellow & purple wires need to be swapped.) Maybe I should have looked at your 550E build videos, but I bought the heli already assembled.
Freddy, First thanks for taking the time to help our fellow heli people. Completed my 550e dfc heli. Set up 3gx as per your videos. (3gx 2.1) Throttle/pitch are linear - mean vibration when getting to mid throttle - shakes down to skids - bounces around on ground--any ideas? Thanks
Very Very good video. I have the 3G system but looks to be same process for setup. When you are finding the mid-point (50 in - 50 out) on the radio, are you in Normal mode, Flight(idle-up) mode? which mode? Thanks!
Hi, I thanks to you put my 550e together. My question for you is, can you tell me in your opinion what size battery i should use. I am just doing pattern flying right now none (yet) of the 3D. Thanks
Weather starting to break so here comes the questions. Just want to make sure i am moving the right thing. About to set up a talon 90 on a Futaba T8FG Super. Can you explain Setting up THR - difference between - Limit VS Travel in End Points? It sounds like the two do the same thing. Your servo will go the same distance, Limit it to go this far, Limit its Travel to go this far. One has to be set as low as you can so once the battery is connected once you increase the value one notch at a time until a beep is noticed. That way the Talon 90 learns high and low.
Freddy, Great job on the videos. I just got back into RC after tryin to fly planes when i was 13 w an open gimbled MRC radio (doubt you've even heard of it) But at 50+ I never would have figured out how to get my first 6 channel Heli setup..... let alone do the 3gx, if it wasn't for your help...... So thanks
i binded my receiver and its fully working. Its just the 3gx that wont lit up at all no sounds and crap like that. what you said, does that mean that i have to bind my 3gx to my tx as well? i thought thats only for satellites.
Hey Freddy.. I know this is an older vid.. but I noticed you mentioned for satellites only receiver to change a channel or switch to gyro in order for tail gyro to function.. any idea what setting that is on the dx6
so you shouldn't put the servo horns on until your radio is on and at mid stick? cause in my manual it says to put them on during the build... but then how do you know if the servo travel is centered?. in other words you could place the servo horn at 90 by moving the servo gear physically when its on the servo... this is hard to explain...
You can easily center a servo without physically powering it thru your rx. Just designate a spot of the servo's travel that you desire to be the 'center' and make sure that the maximum sweep angles (in both directions) from that center are symmetrical. If you're building a kit and haven't got an rx for it yet, its a hell of a lot easier to do it this way than to tear out an rx from something else.
Hi Freddy ! Just wondering if you heard of anyone having issues going with 2 satellites straight out of 3GX or should i use RX with one satellite coming out of the that ex: AR8000 w/sat . I understand you can't mix satelites dsm2 & dsmx. Thanks for your help with the videos !!
So if i change my receiver to just a Spektrum spm9645 satellite and use my 3gx as a receiver. Do you think that this will work on a Dx6i? thanks for helping
Ya know when it comes to reading and doing it, it's like Chinese to me. (Talking about Multi tasking.) Every where i look on the web i see Spectrum & that. I know some of you guys must have the 8FG Super & feel left out like i do. I need a Align 3gx full setup. Talk about a happy Man. Thanks for the 3Gx all I've seen is Micro Beast X
hi , iam new to this hobby so have problems setting up, can u tell me if ive reversed the polarity on the powering up the 3gx unit will it burn it out? I cant get it to power up now, it was powering up before but not now after relocating it and possibly plugging it in wrong. many thanks stevie
Been out of the hobby for several years and just getting back into it. The whole flybarless thing has me a little confused. I have the exact same setup on this vid. Can you please guide me through the binding process? Again same setup using DX8. Thanks in advance!
Sorry Freddy, could it be that the 3GX is mounted wrong? Isn't it that the G--< logo needs to point to the front of the heli? Or is this not that important?
Hi Freddy, I have Trex 450 pro/3gx/DX8 tx, I've done all the set ups, havent tried doing any 3d yet since Im a noob, but the heli can hover pretty well imo, and it came to the point where I want to do the DIR set up "again". What are the things needed to do before doing the DIR? Do I need to re-bind the heli? OR just set the SERVO AND DR/EXPO to zero? Thank you in advance.
Hey Freddy where do I go in my transmitter to make all 3 of my servo's move straight up and down. Like in pitch. Don;t know how to set up my transmitter Devo 8s. Could you please help me with this problem, Scottie
your normal mode should be as follows ( this is a starting point fine tune from here) pitch -3,0,+12 throttle curve 0,40-50,70,80-90,100 linear is not a good normal curve for proper head speed. also make sure if your vibrating your make sure your blades are not to tight, also make sure your main shaft has no up and down play. no bent parts and your blade tracking is spot on. if vibs persist check your dial gains
You can set pitch curve to be all 50% at all 5 points then you can be sure you are at mid stick no matter what is the stick position. Thats what I always do when setting up main rotor head.
fred my 3gx wont power up i attached all the wires into the 3gx correctly from the receiver and when i turn my heli on only the receiver that shows life but 3gx doesnt make a sound nor light. im using dx6i and ar6115e on trex 250. help.
i am just getting back into the hobby after a 6 or 7 year break i got a grate deal off ebay on really nice a trex 450 v2 it came with a futaba t7c radio and a g4 sim i also picked up a good deal on a used 450 pro dfc i came with a 3gx flbls and an airotronics dual satellites, i replaced the satellites with a futaba r6303sb receiver i got it to boot up the servos move around but that is as far as i got it doesn't seem to respond to the inputs properly can one of you guys walk me through the proper setup procedure ? i cant find any videos with a futaba t7c radio thanks jim
Hi lot people saying to me don't use deens conecters but seeing u r have you had any probs great videos big thank you for yr help. Me helicopter all sorted thanks to you.
hello Freddy!!, I noitice after I finish 3GX setup, and hook up the motor, 3 servos just can't move properly. I have to go trough 3GX setting from DIR to the end, and heli will remain functional for a while, but after I hook up the motor, same problem still. Could you please give me some help? thanks.
Hey Freddy, quick question. I have a 600e trex. It's set up but when I hover it, it has involuntary little pitch pumps. Not sure what it is. Can you or anyone help? Thx!
hmmm very strange. could be a vibration issue check for any vibs. also u may have maybe a cut or exposed wire some where that is shorting or something. also double check you fbl system programing as well
Hi, I'm building a 250 dfc and its finished now but i can't get the end point's right in the dir mode When i'm in the dir mode the 3gx should program the end point's but the elevator end point is way to far out when i'm leaving the dir mode... When in the dir mode the end point's are oke but when i'm leaving the aileron is oke and the elevator is pushing so far that the main shaft is moving. I own a DX7s and reversed one servo the aileron and in the swashplate menu all 3 on -60 H.E.L.P
you can use sat with reciver ex (ar8000 + sat dsmx) sat with sat ex (sat + sat both dsmx,dsm2) using 3gx or for a small heli just use one sat with 3gx all options are trust worthy :)
First when it comes to you a person feels intimidated your knowledge is out of this world. My question for you is this. I have the Futaba T8FG - Super, I am using it for a Trex 550e with the Align 3GX. And the Talon 90. Following things on you-tube i think i did something wrong. I see on line that in order to let the Talon 90 know there your Throttle setting is you at first have to go to the radio and get to the End Point and scroll down to the Throttle setting (3). Now i have on one side 135 - 100 (on Left) and 135 - 100 On right. The 100 i set to the lowest value that was 30, then did the same on the right. I put the stick on the TX to the high position, plug in the Talon and begin to scroll up in value until i hear a beep (@) that point just go up two more settings then, put the Stick on the TX to the low position & repeat the above. here is my problem, when i hit the throttle hold and plug in the batt, things look OK. Now i come out of throttle hold and spool up (blades off) everything is fine. When i begin the spool down, it slows and when i get to the bottom of travel it does not stop. just keeps going slow. The only way i can get it to stop is flip the throttle hold. What is going on. Hope someone can give a little incite.
yes one of two things. first try doing a re calibration on the talon just to make sure you set it right. after do a spool up and drop the stick down. if the motor still turns just go into the travel adjust and slowly bump the low end until it stop or shuts off and your good to go :)
Made sense that you need to make sure radio is at half stick and servos are 90. You would be suprised howmany guys dont even bother. I got my heli on a trade for an extra300. I am going to tear it down to the ground and build it back up because I have no idea what was done as to the build. I will replace all o- rings, clean and lube all parts needing such. Being its over 5 years old, I want to check everything out before flying it.
oh yes this is normal, in dir mode when ur setting up ur endpoints and corection direction it is showing swash movement with full movement, once u exit into the main startup menu (three jumps on swash) you are now seeing what may seem to be little movement for both ail and elev because ur picking up the gain values from the 3gx. if u need further help or explanation of this feel free to call or tex me at 801-654-2803 thanks buddy
Hello Freddy, I have always flown the ar7200bx and know it so well by now that I hardly need the set up manual anymore. I just bought a used 700 DFC with a 3gx. I watched some other set up videos and was intimidated by how complicated the programming seemed. I found your series on the 3gx and with your help I was able to get set up on the first try. I just wanted to thank you for a really great and easy to follow instructional. Keep it up!
This might be an older video, but its priceless to someone like me that JUST picked up an Align Pro, completely built and ready to go but I have no info on it. I was told it was hoovered twice and put away. no crashes. It has many upgraded parts as well as all the upgrades. It is NOT flybarless. I may convert it to flybarless but need someone that knows this stuff better than myself.
Incredibly helpful!! I ordered an align 3gx earlier today for a mini Titan e325. I was a little worried that the 3gx would not be as easy to setup as my beastx. Your videos make it look simple!! Thank you
man i just set up a 3gx with satellite for the first time couldn't figure out why the tail wasn't working after about 30 mins i remembered this video ..for got to set gyro sw to aux 2 ..so glad you made this vid
Thanks for doing this set of videos. I've been struggling to understand how to setup a Trex 500 with a 3GX and nothing I've found elsewhere has come as close as your vids to explaining clearly the steps required.
thanks for replying and greetings from australia.in the manual it goes further with 3gx thottle calibration-flight mode setting-ail roll rate-elev end point setting-ail end point setting-swash dampening setting-swash accelerate setting- Do you need to do any of this??? Iam into sports flying.i appreciate all your hellp and your willingness to share your knowledge.cheers mate,mark
Very clear series...unlike some others. Validated my setup with this post. Keep up the good work!
Hello Freddie, thanks for your great video. I wonder if I can use endpoints to level swash when at full collective or not, thanks, Daniele
Freddy can you tell me how to wire the 3GX, AR8000 receiver and the BEC? I watched your setting up throttle and pitch curves videos. i have a DX7S, according to your video I should make the Normal mode throttle curve as in your video right?
throttle menu has N,I,H.
What is the 3D mode? is it I or H? for 3D mode I should change my curves look like your drawings right?
I couldn't find a video of showing the setting up a radio.
Thank you
Great video. Clear, concise, and very informative. I just put together a 550e and I'm trying to set up the 3GX. The problem is that even when I'm in DIR mode, when I raise the throttle the motor spools up. I have no idea why, any ideas? I have a separate BEC which is supplying power to to the 3GX, but when I remove the ESC to try to do it that way, I get an error on the 3GX and can't do anything. Any suggestions?
Excellent set of videos. One question is on the 3GX manual it says near the beginning to turn off the Swash mix Function. I don't understand why you would do this and you didn't on your video.
i have watched all 4 parts plus your 2 gyro vids and i have to say they are the best for helpful and valuable setup information that no instruction manual has got.i have just built a trex700E DFC together with dx8 .Please answer this,with the 3GX ,during the setup of the swash endpoint sequence the swash responds in the tests easy to see,but after initialization is complete and the swash jumps up 3x the helis swash doesnt respond with as much movement as in previous tests in setup mode,is ok??
Great video series Freddy - Top Man - Could not have completed the set up of my Align 500 without them. One question - I am using a DX6i radio and cannot find the SW Select option on my radio to set my giro to Aux2. Can you help ??
First, thanks for the great videos. I'm trying to set up a Trex550E with the 3GX & would be completely lost without your series of video guides. As it is, I can't get the correct operation of the pitch servo in cyclic unless I connect it to the throttle connection on the 3GX. This obviously can't be right, but I've checked & tried everything else. The set up is a Futaba T8FG Tx with a Futaba R617FS Rx.. Any ideas Freddie? Many thanks
thank you - we are trying your suggestions - we added another bearing to torque tube and replaced the gray with red on head - I do sport flying -will let you know
hi, so is it normal for a servo to go back to center slowly when i use aileron or elevator? i thought it suppose to respone fast like in your video. the servos move fast back up when its in DIR mode but not when its normal mode.
Yes in the setup modes the Gyros are not active so they are not looking to counter balance so the servos will act as if there is no gyro. Once programming is exited the gyros are active, and if the Heli is just sitting there they seem to behave oddly because they are following the programming and waiting for the Heli to move so it can correct it.
Hi Freddie, To save you time, ignore my previous question regarding the Pitch servo cyclic response. I've just been told that the Trex550E-3GX manual 3GX wiring instructions are wrong, at least for Futaba Rxs! (see page 17 The yellow & purple wires need to be swapped.)
Maybe I should have looked at your 550E build videos, but I bought the heli already assembled.
Where did u get servo arms from?? They look great!!!
Freddy, First thanks for taking the time to help our fellow heli people. Completed my 550e dfc heli. Set up 3gx as per your videos. (3gx 2.1) Throttle/pitch are linear - mean vibration when getting to mid throttle - shakes down to skids - bounces around on ground--any ideas? Thanks
Your videos are awesome, which do you think is better for a first time build (T-Rex 250 DFC), the Beasts microbeast or the Align 3gx?
Very Very good video. I have the 3G system but looks to be same process for setup. When you are finding the mid-point (50 in - 50 out) on the radio, are you in Normal mode, Flight(idle-up) mode? which mode? Thanks!
Hi, I thanks to you put my 550e together. My question for you is, can you tell me in your opinion what size battery i should use. I am just doing pattern flying right now none (yet) of the 3D. Thanks
for a 550e i would use a 5000 mah pack with and like a 35-65 c disscharge and 6 cells of course
Weather starting to break so here comes the questions. Just want to make sure i am moving the right thing. About to set up a talon 90 on a Futaba T8FG Super. Can you explain Setting up THR - difference between - Limit VS Travel in End Points? It sounds like the two do the same thing. Your servo will go the same distance, Limit it to go this far, Limit its Travel to go this far. One has to be set as low as you can so once the battery is connected once you increase the value one notch at a time until a beep is noticed. That way the Talon 90 learns high and low.
Freddy,
Great job on the videos. I just got back into RC after tryin to fly planes when i was 13 w an open gimbled MRC radio (doubt you've even heard of it) But at 50+ I never would have figured out how to get my first 6 channel Heli setup..... let alone do the 3gx, if it wasn't for your help...... So thanks
i binded my receiver and its fully working. Its just the 3gx that wont lit up at all no sounds and crap like that. what you said, does that mean that i have to bind my 3gx to my tx as well? i thought thats only for satellites.
Hi. can you explain how to install 2 spektrum satelite receivers instead of a standard receiver when using the 3GX?
Hey Freddy.. I know this is an older vid.. but I noticed you mentioned for satellites only receiver to change a channel or switch to gyro in order for tail gyro to function.. any idea what setting that is on the dx6
Hi. Any advice on powering the 3GX with a seperate RX battery?
so you shouldn't put the servo horns on until your radio is on and at mid stick?
cause in my manual it says to put them on during the build... but then how do you know if the servo travel is centered?. in other words you could place the servo horn at 90 by moving the servo gear physically when its on the servo... this is hard to explain...
You can easily center a servo without physically powering it thru your rx. Just designate a spot of the servo's travel that you desire to be the 'center' and make sure that the maximum sweep angles (in both directions) from that center are symmetrical.
If you're building a kit and haven't got an rx for it yet, its a hell of a lot easier to do it this way than to tear out an rx from something else.
scrfce123 Or use an arduino and set the servo to 90 (just loop 90 every few ms) and you're set!
Hi Freddy ! Just wondering if you heard of anyone having issues going with 2 satellites straight out of 3GX or should i use RX with one satellite coming out of the that ex: AR8000 w/sat . I understand you can't mix satelites dsm2 & dsmx. Thanks for your help with the videos !!
So if i change my receiver to just a Spektrum spm9645 satellite and use my 3gx as a receiver. Do you think that this will work on a Dx6i? thanks for helping
Where's the best place to buy a DX8?
very nice video freddy ,keep up the great job
Ya know when it comes to reading and doing it, it's like Chinese to me. (Talking about Multi tasking.) Every where i look on the web i see Spectrum & that. I know some of you guys must have the 8FG Super & feel left out like i do. I need a Align 3gx full setup. Talk about a happy Man. Thanks for the 3Gx all I've seen is Micro Beast X
hi , iam new to this hobby so have problems setting up, can u tell me if ive reversed the polarity on the powering up the 3gx unit will it burn it out? I cant get it to power up now, it was powering up before but not now after relocating it and possibly plugging it in wrong. many thanks stevie
Been out of the hobby for several years and just getting back into it. The whole flybarless thing has me a little confused. I have the exact same setup on this vid. Can you please guide me through the binding process? Again same setup using DX8. Thanks in advance!
Sorry Freddy, could it be that the 3GX is mounted wrong? Isn't it that the G--< logo needs to point to the front of the heli? Or is this not that important?
I have this FBL but I wanna upgrade it to the Radiomaster NEXUS. Is it worth?
@@NorgeSquad there are actually a lot of good FBL options today. I would defiantly stay up to date and current with your fbl for sure.
What is the battery you are using on your DX8?
Hi Freddy, I have Trex 450 pro/3gx/DX8 tx, I've done all the set ups, havent tried doing any 3d yet since Im a noob, but the heli can hover pretty well imo, and it came to the point where I want to do the DIR set up "again". What are the things needed to do before doing the DIR? Do I need to re-bind the heli? OR just set the SERVO AND DR/EXPO to zero? Thank you in advance.
i am not quite sure what u mean by " you came to a point where u need to re do DIR" please expalin more if possibel
Freddy Cordova Hi sorry. I noticed my blades are not zeroed, so changed my mind and I thought I'd like to do the DIR again.
Thx
freddy, what if i have the new DX6 which GYRO = gear only can i still use it instead the aux which is not present to my transmitter...thanks..
Hello Freddy. love the videos.
I`ve like to add a power switch to ease dir mode.
My align BG71019A has three leads.How does this install?
Nice job! Finally someone starting from the beginning..
Hey Freddy where do I go in my transmitter to make all 3 of my servo's move straight up and down. Like in pitch. Don;t know how to set up my transmitter Devo 8s. Could you please help me with this problem, Scottie
i'm using just a satelite on my 3gx and DX6i. i can't find the SW SELECT to put my gyro to aux 2?
your normal mode should be as follows ( this is a starting point fine tune from here)
pitch -3,0,+12
throttle curve 0,40-50,70,80-90,100
linear is not a good normal curve for proper head speed. also make sure if your vibrating your make sure your blades are not to tight, also make sure your main shaft has no up and down play. no bent parts and your blade tracking is spot on. if vibs persist check your dial gains
you are a beast with helicopters dude
You can set pitch curve to be all 50% at all 5 points then you can be sure you are at mid stick no matter what is the stick position. Thats what I always do when setting up main rotor head.
fred my 3gx wont power up i attached all the wires into the 3gx correctly from the receiver and when i turn my heli on only the receiver that shows life but 3gx doesnt make a sound nor light. im using dx6i and ar6115e on trex 250. help.
Can you use this G Pro system with a FrSky Taranis Plus TX / RX?
ummmm....i dont actually think the dx6i has that feature ? ill have to check into it but i dont think it does.
Great info. Thanks for the help Freddy. atb.
Hey can the new motor mount on the v2 and the servo thanks
i am just getting back into the hobby after a 6 or 7 year break i got a grate deal off ebay on really nice a trex 450 v2 it came with a futaba t7c radio and a g4 sim i also picked up a good deal on a used 450 pro dfc i came with a 3gx flbls and an airotronics dual satellites, i replaced the satellites with a futaba r6303sb receiver i got it to boot up the servos move around but that is as far as i got it doesn't seem to respond to the inputs properly can one of you guys walk me through the proper setup procedure ? i cant find any videos with a futaba t7c radio thanks
jim
ummm it sounds like u just need to revers the pitch servo ??
Say brother anyway you can do a video using the 8FG Super. Thanks
Freddy will this DX8 setup work with the new dx6
Hi lot people saying to me don't use deens conecters but seeing u r have you had any probs great videos big thank you for yr help. Me helicopter all sorted thanks to you.
Got my 60 size excell going today but scared to death to lift off any sugestions
Double triple check everything, then just SEND IT lol and remember to take some breathers and relax. As always make sure you Fly Safe Buddy
Freddy, My 3gx keeps falling out of DIR mode. Takes a quick press and it's back. Any ideas?
hello Freddy!!, I noitice after I finish 3GX setup, and hook up the motor, 3 servos just can't move properly. I have to go trough 3GX setting from DIR to the end, and heli will remain functional for a while, but after I hook up the motor, same problem still. Could you please give me some help? thanks.
Lihang Yang hmmm may be a software error. have you tried down grading then re up grading. also what version are you running currently
5.0, i just found out if i turn on radio first, everything works fine. Maybe i shouldnt power on the 3gx before i turn on the radio
yes lol this is always the case always the radio first no matter what
Thanks for this video and all of them!
REMEMBER?
REMEMBER THE SABBATH.
IF THE CROSS CAN FLY
SO CAN I
REMEMBER THAT BABE
Thanks
Hey Freddy, quick question.
I have a 600e trex. It's set up but when I hover it, it has involuntary little pitch pumps. Not sure what it is. Can you or anyone help?
Thx!
hmmm very strange. could be a vibration issue check for any vibs. also u may have maybe a cut or exposed wire some where that is shorting or something. also double check you fbl system programing as well
Thanks!
no end point s do not serve that function. swash mix and centering the servos is what u must use.
Hi Freddy, is there a some way you can teach me to setup my trex 600 with 3g align fbl with JR x9303 Tx thx Doddie
i guess im dumb i didnt realsize you had to bind to the 3gx, thought it was just the transmitter and reciever.
Hi,
I'm building a 250 dfc and its finished now but i can't get the end point's right in the dir mode
When i'm in the dir mode the 3gx should program the end point's but the elevator end point is way to far out when i'm leaving the dir mode...
When in the dir mode the end point's are oke but when i'm leaving the aileron is oke and the elevator is pushing so far that the main shaft is moving.
I own a DX7s and reversed one servo the aileron and in the swashplate menu all 3 on -60
H.E.L.P
you can use
sat with reciver ex (ar8000 + sat dsmx)
sat with sat ex (sat + sat both dsmx,dsm2) using 3gx
or for a small heli just use one sat with 3gx
all options are trust worthy :)
Sweet, I figured, but thought I would ask the expert, thanks again!!
Thanks a lot Freddie
First when it comes to you a person feels intimidated your knowledge is out of this world. My question for you is this. I have the Futaba T8FG - Super, I am using it for a Trex 550e with the Align 3GX. And the Talon 90. Following things on you-tube i think i did something wrong. I see on line that in order to let the Talon 90 know there your Throttle setting is you at first have to go to the radio and get to the End Point and scroll down to the Throttle setting (3). Now i have on one side 135 - 100 (on Left) and 135 - 100 On right. The 100 i set to the lowest value that was 30, then did the same on the right. I put the stick on the TX to the high position, plug in the Talon and begin to scroll up in value until i hear a beep (@) that point just go up two more settings then, put the Stick on the TX to the low position & repeat the above. here is my problem, when i hit the throttle hold and plug in the batt, things look OK. Now i come out of throttle hold and spool up (blades off) everything is fine. When i begin the spool down, it slows and when i get to the bottom of travel it does not stop. just keeps going slow. The only way i can get it to stop is flip the throttle hold. What is going on. Hope someone can give a little incite.
yes one of two things. first try doing a re calibration on the talon just to make sure you set it right. after do a spool up and drop the stick down. if the motor still turns just go into the travel adjust and slowly bump the low end until it stop or shuts off and your good to go :)
Seus vídeos me ajudaram muita coisa
Made sense that you need to make sure radio is at half stick and servos are 90. You would be suprised howmany guys dont even bother. I got my heli on a trade for an extra300. I am going to tear it down to the ground and build it back up because I have no idea what was done as to the build. I will replace all o- rings, clean and lube all parts needing such. Being its over 5 years old, I want to check everything out before flying it.
you want to be in normal mode with a linear pitch curve (0,25,50,75,100)
been using deans for years lol no probs here , but its all personal preference buddy
u have to bind the 3gx first
best x all the way all day
gyro gain ??? if you watch my gyro setup it should explain my friend :)
oh yes this is normal, in dir mode when ur setting up ur endpoints and corection direction it is showing swash movement with full movement, once u exit into the main startup menu (three jumps on swash) you are now seeing what may seem to be little movement for both ail and elev because ur picking up the gain values from the 3gx.
if u need further help or explanation of this
feel free to call or tex me at 801-654-2803
thanks buddy
i tried to text you but it failed ,i'll try find out why,thanks
хоть я не слова не понял но спасибо