I think tutorial videos like this should always demonstrate full teardown using only the space accessible from the front or back (not from the side). The parts of the rails that connect to the rack seem like they could be pretty hard to detach unless you have small fingers if you cannot access the rail from the side panels.
Okay, now why doesn't mine slide all the way in? There's about a 2 inch gap between the front of the rack and where the face of the server stops. The slide always return to the same position regardless of of how deep the rails are set. It fit perfectly fine when I tested it out, and now that I go to put it back on the rack I can't figure it out for the life of me. Driving me absolutely batty.
Hey man. I had this same issue. The problem is the server you have is too long for the type of rail. There is a small metal piece at the end of each rail that stops the server from going further. Take some pliers and rip it off and it will work
The issue I have is on how to remove the rails from the server cabinet. I have been looking online for a way to remove the guide rail kit from those holes. I mis-aligned one end of the rail kit and I can't seem to find a way on how to uninstall it from the server cabinet so I can re-seat it properly.
great video, I have some server are HP DL360 G9, all the rails are PN663201-B21, but servers need to be mount on U40 and above, they're very high, how could we lower the server into that positon? we have to do the complicated work on the ladder, 663200 b21can easily push server in, may i know if PN663201 also can do it this way?a
Still very usefull in 2022. Thank you man 🙏🏻
I think tutorial videos like this should always demonstrate full teardown using only the space accessible from the front or back (not from the side). The parts of the rails that connect to the rack seem like they could be pretty hard to detach unless you have small fingers if you cannot access the rail from the side panels.
You are 100% right. The detach from is horrible when you don't have space on the sides
Thanks for this video. Just getting into the server world so this was very informative.
Still very usefull in 2023. Thank you man!
Very useful in 2024 ..thanks
Thank you so much :) This was very helpful :)
Nice Explanation
Okay, now why doesn't mine slide all the way in?
There's about a 2 inch gap between the front of the rack and where the face of the server stops.
The slide always return to the same position regardless of of how deep the rails are set.
It fit perfectly fine when I tested it out, and now that I go to put it back on the rack I can't figure it out for the life of me. Driving me absolutely batty.
Hey man. I had this same issue. The problem is the server you have is too long for the type of rail. There is a small metal piece at the end of each rail that stops the server from going further. Take some pliers and rip it off and it will work
GREAT, Thank you
I bought a ProLiant DL 380 and got only the slider . .. cable management arm is missing 😭
How do you remove this particular rail system?
It's very difficult. The clips on the inside are impossible to reach. Terrible design!
Tnq sir
The issue I have is on how to remove the rails from the server cabinet. I have been looking online for a way to remove the guide rail kit from those holes. I mis-aligned one end of the rail kit and I can't seem to find a way on how to uninstall it from the server cabinet so I can re-seat it properly.
You are 100% right. The detach from is horrible when you don't have space on the sides
Thank you 🙏🏾
awesome! thank you!
good job, thanks
great video, I have some server are HP DL360 G9, all the rails are PN663201-B21, but servers need to be mount on U40 and above, they're very high, how could we lower the server into that positon? we have to do the complicated work on the ladder, 663200 b21can easily push server in, may i know if PN663201 also can do it this way?a
They haven't thought that one
dear massage to me please
My DL360 isn't releasing when I pull down the tabs in the front. I'm pulling down the tabs that say DL360 gen10 on both sides. Any suggestions?
Sir
I have HPE DL560 SERVER, I thought a
Rack box model please tell me rack box name sir
Greaaaaaaaaaaaaaaaaaaaaaaaaaat
These rails are pure garbage. How do you remove these fuckin things?