I do my oil changes myself as well, but an old driver told me to fill out with oil first the oil filter. I really cant see that option doable since the oil filter comes head in from the top. I see you as well didnt put any oil in the oil filter and wanted to make sure that this is the right way. Thanks and Merry Christmas🎄
Filling up oil in oil filters that does not apply for dd15 motors, cuz it has paper filters, as soon as you pour oil in oil housing it’s going straight to the block, it works only for metal oil filter.
Definitely appreciate the video. Definitely took note of the oil and fuel filter change. Will have to revisit for all the grease points. Got a new sub here since I plan on picking up a Cascadia in the coming days
Great video. Few tips. Use only OEM fuel filters. Had a problem recently with aftermarket filters. Didn't fit quite right. Also grease the fuel filter bottoms liberally and torque to spec & mark the position. I was just freehanding it before trying to be careful because they're plastic but the smaller filter cap needed replacing ($86) due to over tightening. Remember these hard plastic caps are getting old & brittle. I use a rubber band & a coffee filter on the tip of the bottle after I siphon some fuel & reintroduce into the filter cavities. Also theres 4 more grease points. 2 on each side of the fifth wheel pivot. They're usually caked up with mud & crud. Wipe down those nipple tips before greasing so as not to introduce dirt & grime.
Here is what i do to make it easier then this guy. Get your self two $3 5 gallon buckets from walmart along with two 5 gallon oil buckets from Walmart. Also get a easy drain oil tap installed on your cascadia, this will let you open and close the oil drain plug with no mess like a water faucet. Open fill plug grab your bucket drain and close the tap until all oil is gone. Fill oil but keep the old 5 gallon bucket. Next time you change the oil you will use those two old oil bucket as old oil storage so you can transport them to your nearest AutoZone to get rid of them. Zero mess and you wont need a oil catch pan. Or you wont need to lift or drive your cascadia over wooded blocks. With this method I could change the oil faster on my truck than I could on my car.
Thanks for the advise, but I found this the easy way for me and if you could notice I did not had any oil spills either, also I do have oil drain plug on my oil pan.
I have a lot of tools at the house, but I don’t carry it all with me, next time I will make a video about the truck I will try to include a small clip what tool every owner op need to carry with him. Thanks for comment
Good morning and thank you for the informational video, you’re funny you say you have to pump it about 400 times 😆😆😆😆😆, I guess by now the whole family is over so you can have a barbecue Weekend, well listen really appreciate it you always bring something from somebody, 👋👌👍💪✌️
I bought mine with no records with 640k miles, it ran really good until 980k miles until one injector got stuck in open position, so in the morning my truck didn’t want to start cuz of no fuel pressure, i was on the road so I found a diesel shop and one of the Machenics came out to look at it and he decided to start it with engine starter, and the motor just took off, until it blow up💥so after that I do everything g my self.
With prices going up and up.. A typical dd15 oil change at the big shops are approx $530.00. doing your own maintenance gives you a heads up by reducing maintenance cost..
That oil drain valve is installed with an adapter? And where did you buy it? I bought Fumoto T211 from Amazon but not sure if I need an adapter as well. I have the same kind of an engine. Thank you
Just with oil change it will not effect how your truck will start after the change, some guys will use starting fluid to start the truck after the fuel filter change, I will highly recommended not to use any starting fluids on Diesel engines, if you do the job wright and prime the system like you should it will start no problem, Diesel engine can cause diesel run away witch will blow your motor, be really careful with that stuff
I usually go by if I know a person that got a brand new truck and he been using rotella oil all his life and his truck is running very healthy when it has over a million miles to me that’s a good sign that the oil is pretty good. I know few guys that that’s all they been using since they got the truck brand new and their trucks is a good bit over a million now so that’s why I’m using it lol
@@andreykichuk thanks buddy that works for me then can’t beAt real works results instead of marketing on these bottles. Also do you use Lucas oil stabilizer or any fuel additives?
@@classicjay7786 I don’t use anything for motor oil or for the fuel, truck runs really good does not burn oil at all, the only time that I do use anything is anti gel for fuel if I run in extreme freezing weathers.
@@chrissuggs8521 yes this is way to much, Freightliner is saying 45k but I’m not gonna do that that’s to high, if you use full synthetic oil maybe I would go 30k but not more than that
@@andreykichuk And by a chance have you ever use the product Pittsburghpower max mileage? If you happen to check out some reviews on it online I just ordered me a gallon jug going to try it out.
I can’t say nothing good nothing bad about t6, but I do know that I put 600,000+ miles and it does really good, I also know ppl personally that million + miles on rotella t4 and had 0 issues. So for me there is no reason to switch between oils, also it’s not very healthy for the motor to switch between different brand of oils .
@@andreykichuk i bought my first truck and I spoke to the owner I bought it from and he said he would put the cheapest oil. So I want to start putting good oil on it. What should I do purchase cheap oil or start with t6 and never look elsewhere on oils
It’s not just about saving, when you do your own oil changes you know every is done the write way, plus you going underneath the whole truck while greasing inspect everything, one time I found cracked brake drum, loose ground, rubbed wires and etc…..
Nice job explaining everything! Just gave my Cascadia a PM and it was my first time! Thanks for showing the grease points!!
NP Thank you for the comment
Very nice job explaining the procedures for a complete PM Service.
Thank you bud
Thanks man , I’m about to do a oil change for the first time on my 2016 Cascadia and your video help me a lot
No problem, glad I could help.
Great video! going to try n do a pm on mine for the first time.this video was very helpful thanks boss
Glad I could help
This video is the only one i see they do EVERYTHING when doing a PM 🤙🤙👏
Thanks for watching the video, it is very important to take care of your equipment if you want it to treat you write, I try my best anyways. 👍
I do my oil changes myself as well, but an old driver told me to fill out with oil first the oil filter. I really cant see that option doable since the oil filter comes head in from the top.
I see you as well didnt put any oil in the oil filter and wanted to make sure that this is the right way.
Thanks and Merry Christmas🎄
Filling up oil in oil filters that does not apply for dd15 motors, cuz it has paper filters, as soon as you pour oil in oil housing it’s going straight to the block, it works only for metal oil filter.
Definitely appreciate the video. Definitely took note of the oil and fuel filter change. Will have to revisit for all the grease points. Got a new sub here since I plan on picking up a Cascadia in the coming days
Thank you for showing interest in my video, feel free to ask any question about the truck when you get it.
@@andreykichuk indeed!
Thanks Handy Andy. Good lesson for us old timers. Didn't have to listen too much extra gabbin">
Thank you so much God bless.
Great video. Few tips. Use only OEM fuel filters. Had a problem recently with aftermarket filters. Didn't fit quite right. Also grease the fuel filter bottoms liberally and torque to spec & mark the position. I was just freehanding it before trying to be careful because they're plastic but the smaller filter cap needed replacing ($86) due to over tightening. Remember these hard plastic caps are getting old & brittle. I use a rubber band & a coffee filter on the tip of the bottle after I siphon some fuel & reintroduce into the filter cavities. Also theres 4 more grease points. 2 on each side of the fifth wheel pivot. They're usually caked up with mud & crud. Wipe down those nipple tips before greasing so as not to introduce dirt & grime.
Yes sir, always get my filters from WWWilliams Detroit
Luber Finer works fine brah
Time for the carnita asada compa 🍻 gonna do my first oil/fuel filter change this weekend
You can do it, nothing to it, just make sure you put all new rubber seals with a little grease on them
Solid Video, Great Detail! Thanks!
Here is what i do to make it easier then this guy. Get your self two $3 5 gallon buckets from walmart along with two 5 gallon oil buckets from Walmart. Also get a easy drain oil tap installed on your cascadia, this will let you open and close the oil drain plug with no mess like a water faucet. Open fill plug grab your bucket drain and close the tap until all oil is gone. Fill oil but keep the old 5 gallon bucket. Next time you change the oil you will use those two old oil bucket as old oil storage so you can transport them to your nearest AutoZone to get rid of them. Zero mess and you wont need a oil catch pan. Or you wont need to lift or drive your cascadia over wooded blocks. With this method I could change the oil faster on my truck than I could on my car.
Thanks for the advise, but I found this the easy way for me and if you could notice I did not had any oil spills either, also I do have oil drain plug on my oil pan.
I usually take mine to nearest garbage place where you can recycle the oil
Good point bro, u r right after draining oil you first run the engine then change the fuel filters
Alpha Wolves yes sir, have to take care of that motor🙂
Thank you brother, God bless you. Good job. Really helpful video
Thank you, glad I could help.
Where do you drain used oils. Thank you for good videos. 👍
Hello, I usually go to nearest waste management and drain it there, they have this special place for oil.
Great video 👍
Excellent video. Thanks.
You welcome. Good luck on your truck
Nice! Very good information🎉
Glad I could help
Thx man.... I really appreciate...good schooling..👊
Nice video!
Thank you
Nice video bro thanks for taking the time and share, where you take the burn oil?
Uselly they don't like to take more than 2 gallons
I always take it to the waist garbage place, they have this tanks special for oil
Thank you brother for this video
You welcome, hope it was helpful.
Awesome video my friend. Thank you!
You welcome, hope it helped you
Gracias por la demostración. Te la rifastes. Great video..👍🏾
Awesome brother
Thanks
Can you make a video about the tools you have or tools for oops
I have a lot of tools at the house, but I don’t carry it all with me, next time I will make a video about the truck I will try to include a small clip what tool every owner op need to carry with him. Thanks for comment
Good morning and thank you for the informational video, you’re funny you say you have to pump it about 400 times 😆😆😆😆😆, I guess by now the whole family is over so you can have a barbecue Weekend, well listen really appreciate it you always bring something from somebody, 👋👌👍💪✌️
Awesome video. Looking at a 2011 tomorrow. 850k miles. No repair records. Red flag or no?
I bought mine with no records with 640k miles, it ran really good until 980k miles until one injector got stuck in open position, so in the morning my truck didn’t want to start cuz of no fuel pressure, i was on the road so I found a diesel shop and one of the Machenics came out to look at it and he decided to start it with engine starter, and the motor just took off, until it blow up💥so after that I do everything g my self.
You will probably have to replace oil pump & rings, injector cup o-rings, & EGR actuator soon on that 2011 if they haven’t already
Well explained! Thanks
You welcome.
You could always use a torque wrench for you oil filter caps. It tells you the torque specs. 1/2" drive.
Yes you right, but I usually do it snug and it never gave me problems.
感恩了解，謝謝分享！
Good video, thank you!
Good Video!!
Good Job Man
What are u using when installing the new o rings? U r doing some lubrication everytime...is it Grease?
@@SS-vo3dz the lubricant comes with the filter kit
Thank you very much for the video now I don’t need to spend 300 $ i will do it myself
Glad I could help, it’s always good to save some $
@@andreykichuk yes sir
God job. Nice
How often to change oil? And what oil to use for 325K miles
Have you had any issue with the drain plate switch by getting clocked?
With prices going up and up.. A typical dd15 oil change at the big shops are approx $530.00. doing your own maintenance gives you a heads up by reducing maintenance cost..
Can you please tell me the name and the part number for the drain plate switch thank you
Where do u get all the parts from and how much does it cost
@@YouToo510 I get all the parts from ww Williams all filters and oil around $350
Very smart guy!!!
I’m getting there lol
How often do you change your fuel filter and fuel water separator?
I change my fuel filters same time I do oil change witch is 20k miles, water separator every 40k miles, every other oil change.
That oil drain valve is installed with an adapter? And where did you buy it?
I bought Fumoto T211 from Amazon but not sure if I need an adapter as well. I have the same kind of an engine.
Thank you
No adopter, screws straight to the oil pan.
@@andreykichuk thank you so much. That was a quick answer 👍
how many liters/gallons of motor oil does 2019 Cascadia Take?
Where do you recycle used oil?
I take it to WM most of them have oil drums to dump it too
Good job 👍🏼
Thank u
My question is why do most guys have to use starting fluid to start the truck after oil change?
Just with oil change it will not effect how your truck will start after the change, some guys will use starting fluid to start the truck after the fuel filter change, I will highly recommended not to use any starting fluids on Diesel engines, if you do the job wright and prime the system like you should it will start no problem, Diesel engine can cause diesel run away witch will blow your motor, be really careful with that stuff
Where did you buy the quick drain plug
Ebay
How much you pay for all filter and from where you bye that
I buy mine from wwwilliam, not sure on the price will look it up and let you know
How much did u spend with all the filter and oil
Any specific reason why you use shell rotella in your DD15 engine?
I usually go by if I know a person that got a brand new truck and he been using rotella oil all his life and his truck is running very healthy when it has over a million miles to me that’s a good sign that the oil is pretty good. I know few guys that that’s all they been using since they got the truck brand new and their trucks is a good bit over a million now so that’s why I’m using it lol
@@andreykichuk thanks buddy that works for me then can’t beAt real works results instead of marketing on these bottles. Also do you use Lucas oil stabilizer or any fuel additives?
@@classicjay7786 I don’t use anything for motor oil or for the fuel, truck runs really good does not burn oil at all, the only time that I do use anything is anti gel for fuel if I run in extreme freezing weathers.
@@andreykichuk thanks mine neither has 657k doesn’t burn any oil great reliable engine
@@classicjay7786 still running with def?
How many miles do you change your oil and filters ? I have a 2016 DD15
I replace oil every 20k
@@andreykichuk thanks man. Someone told me 50k and I thought that was a little extreme right?
@@chrissuggs8521 yes this is way to much, Freightliner is saying 45k but I’m not gonna do that that’s to high, if you use full synthetic oil maybe I would go 30k but not more than that
@@andreykichuk That’s exactly what I was thinking I appreciate the information. I’ll keep that in mind and most likely change every 20 K
@@andreykichuk And by a chance have you ever use the product Pittsburghpower max mileage?
If you happen to check out some reviews on it online I just ordered me a gallon jug going to try it out.
I have a 09 cascadia dd15 is rotella t6 synthetic good or should I stay away from synthetic. people say is too thin.
I can’t say nothing good nothing bad about t6, but I do know that I put 600,000+ miles and it does really good, I also know ppl personally that million + miles on rotella t4 and had 0 issues. So for me there is no reason to switch between oils, also it’s not very healthy for the motor to switch between different brand of oils .
@@andreykichuk i bought my first truck and I spoke to the owner I bought it from and he said he would put the cheapest oil. So I want to start putting good oil on it. What should I do purchase cheap oil or start with t6 and never look elsewhere on oils
👍 I hope we won't have to wait 12 years for next video 😄
АНДРІЙ БАУЭР MODERN TRUCKING I’ll do better this time lol
Sometimes I assume it's not always easy to be making videos while working on the truck
What kind of wood did you use for the ramps?
Just a regular 2x8 cut it in different sizes to make it step up every foot
@@andreykichuk thank you.
I only grease my suspension everything oil change.. reduces excess grease.. drive train 5th wheel Everytime
What grease do you use and where do you purchase your shell oil
Nomad I use MasterPro EP Moly Grease and I buy oil from Sams Club when it’s on sale, it will be the best price from anywhere you go if it’s on sale.
@@andreykichuk where do you get your grease from ?
@@oldmanbeau9071 I’m getting it from O’Reilly Auto Parts in box of 12 I think.
whats the difference between a Fleet Guard 17810 and a 17511
Could be just a cross reference part number.
Where can I find that drain pan
Dre Alex EBAY item number 114274133382
@@andreykichuk thank you
@@andreykichuk also what oil you use
Dre Alex I use Rotella 15w-40 non synthetic I change oil every 20k miles
@@andreykichuk thanks i will be changing mine Monday appreciate the video
t4, how many miles can you drive, or how many miles in a cycle
I run 20k miles, ppl drive more but I prefer to change at 20k mark
@@andreykichuk thank you
@@cbenson1820 20k sorry
I like your username😂👌🏼
Elvira Kondor thank you
You just saved yourself a whopping 500 bucks
It’s not just about saving, when you do your own oil changes you know every is done the write way, plus you going underneath the whole truck while greasing inspect everything, one time I found cracked brake drum, loose ground, rubbed wires and etc…..
Awesome video...what kind of oil for those oil nipples?
@@Goloso333 I use grease from Reilly’s Moly grease
Gloves bruh gloves!
Hello brother to brother
Let me where you living
I’m wondering to have reason from you brother
I beg you
if u grease king pins once a week they outlive your grandkids not sure about u joints 😜
Yes if you grease them on schedule every time they will last at least 1 million miles
i was gonna watch your interesting video but when i heard the annoying "music" in the background i terminated it. what's wrong with silence man
@@truckdriver-jr1qr sorry can’t make everyone happy