I absolutely hate being the safety police because I do dumb stuff all the time but the band saw is better for small peices like that. I knocked a fingernail off on my table saw doing tiny peices exactly like you just did. It has a tendency to pull small pieces and tornado them, hence drawing your hands in to the blade. I did small peices for about 12 years before it finally got me. Fortunately the nail mostly grew back.
nice knife, I am surprised by the way the heat treat is done. If it is 12C27 which is stainless I think the heat treat needs to be done a bit differently, in particular I thought you were supposed to hold the knife at the correct temperature for a while before the oil quench. I have done several knifes with carbon steel and if you do get good results with 12c27 with such a simple heat treat I'd be very interested to try it.
Marek Tabi bro you should make a company that sells custom knives Also could I work with you on your RUclips channel I make stuff like this too fuck this sounds so unprofessional anyways would you need or want a partner
Well done ( I am from Thiers, in France, the french capital of knives), and I've never seen this lock system. Nexte time, you'll do the same with a damas blade ?
This is some level 10 DYI badassery. After too many years doing stuff it never occurred to me to flip over a portable belt sander to use as a standing belt sander. Seems obvious now.
beautiful knife, but all I can think is how often that locking mechanism is going for snag on a pocket, or may hurt the user if they're hand slides up the handle
nice work...teda az teraz vidim, ze si slovak :) velmi pekne, sice nie tradicne kutie, ale vysledok je super...preco niekto robi ciastocne kalene cepele a nie cele? ze kalena je len cast ktorou sa reze?
Ahoj Marku, uvažuju koupit stolní brusku, tak jsem se chtěl zeptat, jak jsi spokojený s tím schepachem? Oplatí sa to ? Našel jsem ještě levnější variantu Güde GDS 150 K, stojí třikrát míň, ale specifikace je podobná, co si tom myslíš? Pokračuj v dobré práci :-) dík, Jindra
no ak ti mam pravdu povedat ja uz sa neviem dockat kedy budem mat na to aby som si kupil poriadnu brusku :D na nejake domace hobby pouzitie je postacujuca ale pasi su do toho dost drahe malo vydrzia a ta moja sa dost prehrieva a musel som odpilit plechy co boli okolo brusneho pasu lebo tam zavadzali :) ale ak neplanujes robit velke zlozite projekty tak staci :) s pozdravom Marek :)
Díky, viděl jsem tě právě s tím dělat divy, tak jsem si myslel, že určitě nemůže být tak špatná :D ale ty si holt umíš poradit i s jednoduššíma nástrojema...
looks great but that locking peg would get in the way a lot, this is why no knife uses it ever, why not make a traditional lock? either way it looks great.
Very great work Tabi! But you really should put music in your videos, it's hard to get your watch-time without keeping the viewer hooked. Great work though, keep it up!
If it were me I wouldn’t quench the knife I would slowly drop it in also the heat marks indicate how hard the metal will get when you set it in water. And when you put it in the oven aren’t you just softening the metal?
tento mechanizmus som odkukal od takého starého čínskeho noža a upravil som si ho na svoj nôz :D ja si po večeroch kreslím tie mechanizmy na papier, vystrihujem ich a skúšam ako fungujú :D
Замок не удобный и не надежный, материал клинка-пластилин, закалка выполнялась как попало: температурный режим не понятно какой, среда закалки-тоже, с нормализацией то же самое
Is there any way to see how you made the locking mechanism? I would love to be able to see better!
One of the best knife making videos for people who just interested. Simple design, minimum instruments.
interesting locking mechanism. I've never seen one before!
NIce!
Scary moment there with the glass jar i.e. had one explode on me once and never again!
Thanks for sharing.. Enjoyed!
You do very impressive work....especially considering the tools you have available to work with. Congratulations on a job well done.
Very nice. Love the brass accents in the handle!
thanks :)
Paráda! Si taký slovenský Jimmy Diresta :D
Pekná robota
I enjoyed watching it. Thank you ❤️
how did you get the metal brass looking hex on a thread bolt. Weld it or did come like that cause wtf
I absolutely hate being the safety police because I do dumb stuff all the time but the band saw is better for small peices like that. I knocked a fingernail off on my table saw doing tiny peices exactly like you just did. It has a tendency to pull small pieces and tornado them, hence drawing your hands in to the blade. I did small peices for about 12 years before it finally got me. Fortunately the nail mostly grew back.
using an angle grinder with metal cuting disc to cut wood? is it because u dont sell your knives?
Wow, the knife looks beautiful!
Gorgeous knife. I really love the brass inlays!
nice knife, I am surprised by the way the heat treat is done. If it is 12C27 which is stainless I think the heat treat needs to be done a bit differently, in particular I thought you were supposed to hold the knife at the correct temperature for a while before the oil quench. I have done several knifes with carbon steel and if you do get good results with 12c27 with such a simple heat treat I'd be very interested to try it.
1:12, What kind of glue do you use? Thanks.
How thick do you leave the edge before the quench ?
That was awesome never seen a lock like that. Pretty cool bro
I love it. I want it but how can I buy it?
Looks really pretty.
Do you ever plan on selling a knife or maybe do a giveaway?
That's a great idea :)
Thank you. I dont plan to sell them, maybe in the future when I will have them so many and will not know what to do with them :D
Marek Tabi bro you should make a company that sells custom knives
Also could I work with you on your RUclips channel I make stuff like this too fuck this sounds so unprofessional anyways would you need or want a partner
Kubey knife is selling various folding knife for outdoor. You can have a try. kubeyknife.com/
Very nice work especially with the brass/wood handle
thanks bro :)
Can you explain how the lock works?? I don't understand how it's locking/unlocking?
Slip joint
whats that
Did you just use a table saw for a cross cut???
What steel did you use??
Nice knife. Love the handles
what do you call this solution 6:17 ? Thank you!
We enjoyed your video hope you make some more
Cool knife
Well done ( I am from Thiers, in France, the french capital of knives), and I've never seen this lock system.
Nexte time, you'll do the same with a damas blade ?
Nice knife, but does the flipper not allow it to flip nice? I find this must be the hardest part to overcome with knife design.
How many days did it take you to make the knife?
Don't understand the locking mechanism. But great craftsmanship. Especially with limited tools
Nice work ! Way to take charge and just go for it.
good knife but when you do the sharpness test your not supposed to use force because it's not percice for sharpness
Do you have plans online somewhere?
Nice knife you are the best making knifes
Looks like great. And i have an idea. I think you can make yataghan.
Very nice.
ten mechanizmus se dá plánek sehnat kde? Jinak super nápad!
wait i need to tell you something, GET WELL MARK TABIS MACHINES!
This is some level 10 DYI badassery. After too many years doing stuff it never occurred to me to flip over a portable belt sander to use as a standing belt sander. Seems obvious now.
David R I’ve done it for along time. Make sure to clamp it down it helps in many ways
Yeah I don’t have a standing belt sander I do the same with a portable one
Pekná robota Marek :)
Great job. Making one always beats talking about it
beautiful knife, but all I can think is how often that locking mechanism is going for snag on a pocket, or may hurt the user if they're hand slides up the handle
Which oil r u using buddy for quince...
What kind of glue did you use?
craftmanship all the way
great knife as always
Excelente trabalho PARABÉNS
Where'd you get your belt sander?
That's beautiful
thanks :)
Dam, how do you move so fast?
Its a magic 🤣
Hey could someone tell me what type of wood the first wood he cut was??? It would be very helpful. :)
Bubinga wood... It's in the description! ;-)
@@NaeFliesOnMe THANKS! Sadly I now feel stupid...😥
nice work...teda az teraz vidim, ze si slovak :) velmi pekne, sice nie tradicne kutie, ale vysledok je super...preco niekto robi ciastocne kalene cepele a nie cele? ze kalena je len cast ktorou sa reze?
diky :) par nozou som aj kul :D ciastocne kalenie sa roby preto aby si mal zadnu cast noza meksiu cize aj pruznejsiu,
Ahoj Marku, uvažuju koupit stolní brusku, tak jsem se chtěl zeptat, jak jsi spokojený s tím schepachem? Oplatí sa to ? Našel jsem ještě levnější variantu Güde GDS 150 K, stojí třikrát míň, ale specifikace je podobná, co si tom myslíš? Pokračuj v dobré práci :-) dík, Jindra
no ak ti mam pravdu povedat ja uz sa neviem dockat kedy budem mat na to aby som si kupil poriadnu brusku :D na nejake domace hobby pouzitie je postacujuca ale pasi su do toho dost drahe malo vydrzia a ta moja sa dost prehrieva a musel som odpilit plechy co boli okolo brusneho pasu lebo tam zavadzali :) ale ak neplanujes robit velke zlozite projekty tak staci :) s pozdravom Marek :)
Díky, viděl jsem tě právě s tím dělat divy, tak jsem si myslel, že určitě nemůže být tak špatná :D ale ty si holt umíš poradit i s jednoduššíma nástrojema...
Great work
Bu çakını fiyatı ne kadar
that is really pretty
Не понял как фиксируется клинок???
Nice Job 👌🏼
thanks :)
Very cool but my favorite part was your dog ;)
Other than that good job on the knife
Can u make a falchion knife
He made it look very easy.
do you sell knives? I've seen a lot of your videos and you make some awesome stuff
good job!
what oil you used at 6:10? can you tell me please.
Most likely vegetable oil or any other kind of cooking oil.
Mate your oven is so clean 🤣
You must see it after 4 years of use 🤣
Ahoj Marku, dají se někde na netu sehnat nákresy na zavíráky? Díky Beebo
ahoj, nedaju lebo si ich vymyslam doma sam :D
Díky, holt budu muset rozebrat nějakej co mám doma a chytit inspiraci :-) Díky za odpověď, fandím ti, děláš super práci :-)
tak som aj ja zacal, najskor som znicil plno nozou co mame doma aby som si spravil vlastny :D
Человек-электровеник... 👍
hodně povedené!!!
6:08 Is that oil? and what kind of oil?
it is hidraulic oil
Thanks! :) Love your videos :D Im going to make a hunting knife :P
what kind of steel are you using?
12c27
looks great but that locking peg would get in the way a lot, this is why no knife uses it ever, why not make a traditional lock? either way it looks great.
awesome!
Very great work Tabi! But you really should put music in your videos, it's hard to get your watch-time without keeping the viewer hooked. Great work though, keep it up!
Yeah i can relate to that :)
If it were me I wouldn’t quench the knife I would slowly drop it in also the heat marks indicate how hard the metal will get when you set it in water. And when you put it in the oven aren’t you just softening the metal?
Mike Knupfer you have to quench the knife to make it hard, and you put it in the oven to lessen the brittleness
S!ngularity gotcha but I was taught not to just drop in it there but rather put it in water gradually so it doesn’t crack
he quenched in oil
slow quenching is for water, he used oil
Mike Knupfer don't use water
That knife is pretty sexy. I really appreciate you making these videos of you showing us your cool talents.
beautiful
Good skills
Good video. Sucks that the most important part was left out.
Nice job except for that pin sticking out. Every time you put it in your pocket it's going to get caught.
Marek ten mechanizmus noža si otkial bysom vedel stiahnuť ??? som strateni vole (._.)
prepáč za víslovnosť som magyar :Da asi som tvoj jediní magyarskí fanusik
tento mechanizmus som odkukal od takého starého čínskeho noža a upravil som si ho na svoj nôz :D ja si po večeroch kreslím tie mechanizmy na papier, vystrihujem ich a skúšam ako fungujú :D
dík za otpoved Marek :D
Nice.
12c27 hardening1075 15 min., tempering 210 90 min. ;-)
buen trabajo . Me suscribo. Saludos
Sorry but when you quench the blade DO NOT ever do it with anything glass always do it in something metal
Nice
Superbe !
yea do a give away mate
muy bonito
Keep up bro
thanks :)
Can you please give me that knife
Kozak 👌🏻
I got sad when your belt sander died
zajebisty
I find your lack of safety equipment disturbing
Этот штырь просто убил 😂
Way put on knive in the oil
3 reklamy? :D je vidno ze to robis pre penaze :D :D :D ale nie marek ale ano marek :D
chcem kupit frezu :D
subnautica knife
Замок не удобный и не надежный, материал клинка-пластилин, закалка выполнялась как попало: температурный режим не понятно какой, среда закалки-тоже, с нормализацией то же самое