Will running the hpop lines to the wrong side of the head cause a no start? Thanks for the videos and information love what you are doing in the diesel owners community.
With the angled fittings it is impossible to get a socket on them for using a normal torque wrench. Did you use a crow’s foot with a torque wrench for correct torque values? Is there a “handy dandy” chart available to correct the wrench torque setting when using a crow’s foot?
Big shocker here but we totally guess. It’s a feel thing. But the correct formula is Original Torque Spec * (Effective TQ Wrench Length / Effective TQ Wrench Length + Change In Length) = Final Torque Reading. Then you will adjust from there.
My fear is that since I was told to just finger tighten it down and put some blue thred locker on it, that's all I did and I dont want it to pop loose and leave me stranded in the desert. Ive been stranded for a year in a state far from home. I need this thing prestine. The head fittings may need replaced and I finger tightened the hpop fittings on the hpop itself because I was afraid to torque it too much and break it like I did my Schrader valve return line end. Did I do that wrong? Please tell me what to do. I replaced my hpop with an adrenaline and the lines too. One of the lines sent to me, its end that goes into the passenger side head fitting just keeps popping out of the fitting. Never happened with the old line. So I dont know what could cause that? I also dont have a torque wrench and I know for sure 23 foot pounds is way more than I put on it but I dont know exactly how much that feels like to be accurate
Just bought an adrenaline hpop and their instructions say to remove any crossover lines, its no longer needed and unnecessary failure down the road. Any truth, because i dont really want to take it off?
I seen on another video that when you remove the fuel lines that those seals have to be replaced as they are supposedly a one time use, any feedback is appreciated.
What if anything did you do with the existing copper lines you disconnected from the HPOP ? At the end of the video I can still see them taking up some space
I have got 2002 f250 power stroke can I get just the cross over line my other line’s looks good there stainless would I haft to take check valve out hi pressure oil pump
I have watched a couple of videos besides this one, and some folks get the fittings from Ford and it calls for the use of 680 locktite for the fittings. I noticed none was used here. Is that not necessary with this kit?
Hey I got a question, I just installed new hpop lines including the crossover line.I took out the check valves and everything but now the truck takes forever to start.this didn’t happen before with the old lines.why is this happening?
How many miles on your install? We usually drive a HEUI install several miles before we start chasing conditions. If you took the check valves out of a stock pump, I would start with reinstalling them and see if that corrects the condition.
I recently had my 7.3 quit on me I was driving it and heard like a pop then die I was think hpop lines. It cranks no start but my oil light is on now and engine temp is and no lights whatsoever was on prior to this happened. After I got out and checked it leaked a lot of oil
It's kinda convenient u skipped how route the main engine harness to the bracket. On 7.3 SD the line is right smack in the middle of where this harness has to go! Without removing bracket and just letting the harness lay on the valve cover like a Hoosier or try to go above it, either way the line will rubb a hole in the wiring making it for a sure short in the future! So how do we run the harness now ?
The main harness routing to the bracket doesn’t move. This truck, some redneck took the bracket completely off the truck where the main harness connects to engine harness. What I showed here was how long and sweeping that line transition is. No matter what, you have to keep the harness from the lines, zip ties, whatever it takes. You are correct, there can be contact points, but you can avoid it by going through and making sure that you have everything zip tied out of the way.
I remove the 4x4 shaft so I only have the spindle with the wheel hub . So there’s no need for a manual wheel lock correct . Because theres nothing to lock or free . Just to put a metal cover from an old lock. Please tell me if I am right .
There were torque specs given but no torque wrench was used. Are the numbers just a rough guideline for how much force to apply with my hand? There is a kit without x over pipe. Seems easier and less failure points. How to know which one I should use?
Torque specs are correct, if you aren’t using a TQ wrench, of course pay attention to the values and don’t over tighten. There is a kit without crossover, but we like the kit that includes it.
🔥 Want some CNC Fabrication High Pressure Oil Pump Lines?
www.thoroughbreddiesel.com/cnc424004/
Thanks for the suggestion. Maybe in the future!
@@thoroughbreddiesel Just recieved mine today, thank you!!
this is good work nice video ser from NJ bless you America 🇺🇸
Thank you very much!
Saludos desde Guatemala 🇬🇹 nice video gray tanks with the video from NJ
Great video and explanation with video footage
Thank you very much!
This content is why I will buy from Thoroughbred Diesel.
Thank you!
@ order is in the mail, thanks!
good night I, watching Egan you video nice video GOD bless you and your family from NEW 🆕 Jersey thank you 🙏
God Bless
Thanks, great video
You're welcome!
what does check valve being removed accomplish ?
Increase oil flow.
Has anyone done a dyno test of this mod before and after also curious about the 3" plenums upgrade if that adds any power?
Will running the hpop lines to the wrong side of the head cause a no start? Thanks for the videos and information love what you are doing in the diesel owners community.
I do not think that it will but if they are run to the wrong ports it could.
Why remove the oil check valve, to clean it or remove it completely. What does it accomplish? Thx Mike
Increases flow.
With the angled fittings it is impossible to get a socket on them for using a normal torque wrench. Did you use a crow’s foot with a torque wrench for correct torque values? Is there a “handy dandy” chart available to correct the wrench torque setting when using a crow’s foot?
Big shocker here but we totally guess. It’s a feel thing. But the correct formula is Original Torque Spec * (Effective TQ Wrench Length / Effective TQ Wrench Length + Change In Length) = Final Torque Reading. Then you will adjust from there.
My fear is that since I was told to just finger tighten it down and put some blue thred locker on it, that's all I did and I dont want it to pop loose and leave me stranded in the desert. Ive been stranded for a year in a state far from home. I need this thing prestine.
The head fittings may need replaced and I finger tightened the hpop fittings on the hpop itself because I was afraid to torque it too much and break it like I did my Schrader valve return line end. Did I do that wrong?
Please tell me what to do. I replaced my hpop with an adrenaline and the lines too. One of the lines sent to me, its end that goes into the passenger side head fitting just keeps popping out of the fitting. Never happened with the old line. So I dont know what could cause that? I also dont have a torque wrench and I know for sure 23 foot pounds is way more than I put on it but I dont know exactly how much that feels like to be accurate
@DBCooper3 a full yeat stranded bro? Sounds like you made it. So you had plenty of water and food in your truck to last you the whole year?
Just bought an adrenaline hpop and their instructions say to remove any crossover lines, its no longer needed and unnecessary failure down the road. Any truth, because i dont really want to take it off?
I seen on another video that when you remove the fuel lines that those seals have to be replaced as they are supposedly a one time use, any feedback is appreciated.
The fuel lines on a 7.3 have grommets on them, and yes when removed we suggest replacing.
Can the check valves be left in with the cnc lines? Is there adown side in takeing them out?
No down side to removing them. CNC suggest removing them with their lines.
What if anything did you do with the existing copper lines you disconnected from the HPOP ? At the end of the video I can still see them taking up some space
The copper lines you are seeing are fuel lines to the fuel bowl I believe.
I have got 2002 f250 power stroke can I get just the cross over line my other line’s looks good there stainless would I haft to take check valve out hi pressure oil pump
Give us a call (859) 737-4966.
I have watched a couple of videos besides this one, and some folks get the fittings from Ford and it calls for the use of 680 locktite for the fittings. I noticed none was used here. Is that not necessary with this kit?
No Loctite called for with the CNC lines.
Thank you for taking the time to respond. Much appreciated!
Hey I got a question, I just installed new hpop lines including the crossover line.I took out the check valves and everything but now the truck takes forever to start.this didn’t happen before with the old lines.why is this happening?
My 7.3 did the same thing for about 2 weeks, ended up getting better, I think it's getting air out of the system,
How many miles on your install? We usually drive a HEUI install several miles before we start chasing conditions. If you took the check valves out of a stock pump, I would start with reinstalling them and see if that corrects the condition.
I have an 03 E450 van. Can all this be removed as shown in your video or will I need to move additional parts out of my way?
It’s a little simpler on the E series as you get access to the back of the engine from inside the cab, but yes, everything should be the same.
using a crows foot, this can be done without removing the fuel bowl. it's not easy, but it is possible.
Good afternoon. Do you leave out them 2 springs out
Yes. The check valves are removed to increase flow.
What is the check valve purpose? I understand removing it increases flow, but what is the original design purpose?
To keep from having drain back. Its not an issue with a truck having a good and functioning oil delivery system.
I recently had my 7.3 quit on me I was driving it and heard like a pop then die I was think hpop lines. It cranks no start but my oil light is on now and engine temp is and no lights whatsoever was on prior to this happened. After I got out and checked it leaked a lot of oil
Should have pretty good visibility to the lines. Go over everything very good.
I have heard its a good idea to fill the lines with oil prior to full install to assist the start up and initial running after install. Thoughts?
I hope you are being funny bc I don't think that is even possible...
Question: someone else claims the engine runs quieter with this mod. What is your experience?
How do I torque the fittings to spec with wrenches?
Crows foot adapter for the torque wrench.
You can use a crows foot with torque ratchet.
It's kinda convenient u skipped how route the main engine harness to the bracket. On 7.3 SD the line is right smack in the middle of where this harness has to go! Without removing bracket and just letting the harness lay on the valve cover like a Hoosier or try to go above it, either way the line will rubb a hole in the wiring making it for a sure short in the future! So how do we run the harness now ?
The main harness routing to the bracket doesn’t move. This truck, some redneck took the bracket completely off the truck where the main harness connects to engine harness. What I showed here was how long and sweeping that line transition is. No matter what, you have to keep the harness from the lines, zip ties, whatever it takes. You are correct, there can be contact points, but you can avoid it by going through and making sure that you have everything zip tied out of the way.
I got a 99 f550 7.3
The front high pressure line is leaking like bleeding pig. What lines do I need
Give us a call 1-859-737-4966.
@@johnnyblade3335 did they come with Viton O rings? if not you're going to have a bad day.
@@travisfreutel2733 yep top of the line.
327.000 7.3 6spd manual👍
I remove the 4x4 shaft so I only have the spindle with the wheel hub . So there’s no need for a manual wheel lock correct . Because theres nothing to lock or free . Just to put a metal cover from an old lock. Please tell me if I am right .
Don’t understand the question but if you take the output shafts out you will have a leak.
Great video! Question- Do the ck valves get discarded? Thanks for sharing.
Thanks! Well, I kept ours for my hoard pile but yes normal folks just throw them away!
There were torque specs given but no torque wrench was used. Are the numbers just a rough guideline for how much force to apply with my hand? There is a kit without x over pipe. Seems easier and less failure points. How to know which one I should use?
Torque specs are correct, if you aren’t using a TQ wrench, of course pay attention to the values and don’t over tighten. There is a kit without crossover, but we like the kit that includes it.
How do you torque the fittings? With a crows foot?
I'm still wondering how to torque them as well with no room to work
@@Charles-ij2mh I used my hand as torque wrench. No problems yet.
@alexkram thinking that's the only way, barely past snug. 25- 27 on torque wrench is nothing
is installing the 3rd hose necessary? if so why?
The balance line is not necessary but comes with the kit and is designed to help with the oil supply to both heads.
Just bought this exact pump line kit and only received fittings 1,2,3,5,5,5. Am I missing number 4? I have 2002 7.3
Give us a call please 855-823-5514.
How do you torque the fiittings? With a crows foot?
Yes, and making sure that you use the correct torque multipliers.
What about the springs
Springs come out too.
Did they seriously use three different sizes for the fuel lines on that fuel bowl? 😔
Another engineering marvel!