few comments on this water tank structure, 1. NO drain sump area. 2. NO 150cm concrete exposure on the FGL. 3. NO chamfer on all sides on the concrete. 4. BITUMINOUS paint is required prior to backfilling. 5. Waterproofing Or Epoxy Tank Linking must apply insides the tank.
Nice demo, but you left out many important parts. *Outlet pipes (cleaning and service) should have been fitted before pouring concrete to avoid cutting them when driving. That way, you avoid rust. *There is no overflow pipe provided. Should have installed before concrete. *There is no ventilation pipe installed *Therevis no provision for electrical if installing an ellectic pump. *The outside part of the wall should have added some tar or something to protect the wall from direct contact with the earth/soil/dirt *Manhole to tiny for a human being to get to clean, fix any cracks, or install aftermath fixtures.
I am presently designing such a tank in AutoCAD. If you take each unique piece of rebar and create them as blocks you can then insert blocks of each type. The benefit of this approach is you can then use the DX or data extraction command to count the blocks and make a BOM table of each type of bar and how many will be needed in the project.
The bottom slab act as foundation and supported by soil. This is important to have check the actual bearing pressure and the soil pressure obtain from the tank;ie.dead load +live load and surcharge should not exceed actual bearing pressure of soil.
Good educational video, I suggest it would be better if the corners are done the way we do corners for the Lift Shear Wall. Plus adding rebars at the corners.
There are so manny mistakes, but the biggest are. 1. The wall tie bar shouldn't be on the external part of the bars in the main wall. That means in the wall, the horizontal bar ---(tie wall bars) should be placed in the middle of the vertical bars || (main bars). |: :| | | ➡️ main wall bars on edges. : ➡️ Tie wall bar on the middle.
Agra District R.C.C. Water Tank normal thickness all Side walls of Readymade 2000 Liter. Capacity water Tank in Complete Pieces is seen selling to Peoples Constructing their House.
few comments on this water tank structure,
1. NO drain sump area.
2. NO 150cm concrete exposure on the FGL.
3. NO chamfer on all sides on the concrete.
4. BITUMINOUS paint is required prior to backfilling.
5. Waterproofing Or Epoxy Tank Linking must apply insides the tank.
And also the inlet and outlet pipe
Nice demo, but you left out many important parts.
*Outlet pipes (cleaning and service) should have been fitted before pouring concrete to avoid cutting them when driving. That way, you avoid rust.
*There is no overflow pipe provided. Should have installed before concrete.
*There is no ventilation pipe installed
*Therevis no provision for electrical if installing an ellectic pump.
*The outside part of the wall should have added some tar or something to protect the wall from direct contact with the earth/soil/dirt
*Manhole to tiny for a human being to get to clean, fix any cracks, or install aftermath fixtures.
Good insight
A very nice program!m though I didn't see any plumbing
Awesome presentation 💯
بالتوفيق ❤
This was really helpful. Subbed!
Super 👌
Thank you
I am presently designing such a tank in AutoCAD. If you take each unique piece of rebar and create them as blocks you can then insert blocks of each type. The benefit of this approach is you can then use the DX or data extraction command to count the blocks and make a BOM table of each type of bar and how many will be needed in the project.
this is really amazing man
Thanks for your valuable comments
How you did slab without support under the slab
The bottom slab act as foundation and supported by soil. This is important to have check the actual bearing pressure and the soil pressure obtain from the tank;ie.dead load +live load and surcharge should not exceed actual bearing pressure of soil.
A nice presentation
Nice work but features also need to add, on let, out let , air vent, over flow pipes
Waterprooffing
Sumb
Foot steps
Epoxy painting
So how long have you worked for the steel industry?
عمل رائع جداً
Also we can built by concrete wall between 4.5" bricks walls.
As UK builder evry aspect o Australia concrete tank construction is sensible AN useful for clients and needs of the builders and users
Good educational video, I suggest it would be better if the corners are done the way we do corners for the Lift Shear Wall. Plus adding rebars at the corners.
Dasyat..
Very good
Thanks for your valuable comments
👍👍👍👍👍
There are so manny mistakes, but the biggest are.
1. The wall tie bar shouldn't be on the external part of the bars in the main wall.
That means in the wall, the horizontal bar ---(tie wall bars) should be placed in the middle of the vertical bars || (main bars).
|: :|
| | ➡️ main wall bars on edges.
: ➡️ Tie wall bar on the middle.
Super sir
so where is the water coming from and going to??
Agra District R.C.C. Water Tank normal thickness all Side walls of Readymade 2000 Liter. Capacity water Tank in Complete Pieces is seen selling to Peoples Constructing their House.
Isme plumbing work kaise hoga..
Please uske liye bhi ek video share kijiye..
Sir which software u use for make this video?
Thanks for your Comments. I used SketchUP software for this video.
Itne bars main to Ghar-bar bhik jayega 😅😅
Trying to understand the need for the upper corner rebars purpose. Could someone explain to me please?
Me too need an explanation for that
This is just an educated guess but I think they are stiffeners that provide additional strength and stability by resisting lateral loads
What will be the cost of 1lakh lit under ground water tank of rcc.?
extension name for rebar ?
3500 liters underground water tank ki labour kitni honi chahyey
can you show how to calculate for the bottom bar slab and side wall bars?
❣️
What's the length, width and The depth of the tank
Where is water stopper ? You didn't provide it
nice hole is small, how to cleaning and service.
Looking overdesigned. No plumbing accessories provided. Good for nuclear reactor.
Hahaha nice suggestion
Nice video! which program did you use to make this animation?
Unless that's a giant water tank or you want to store nuclear waste its a little over engineered...
no sleeves?????
Heyy Keerthana
Shuttering not provided in video
Sir were is selves
You say step by step, but I didn't see any wall forms steps, water stops or bracing, sump pump area etc. This is a joke right?
shearing our resources
Where is the water stop..?
থ্যাঙ্ক ইউ
You are most welcome
Where is the bentonite strip?
You're missing the water stop
深坑
Paano po ang porma Niya
i need sketup designeer this type desine
kivabe apply korbo sir bolen
Where's Water line?
Please tellcosting
Cc layer mean
Cement Concrete Layer
Slab casted without formwork!
Ek ek bareek bar zoom karke batao kya kya hai aur kaise lagate hao
I clicked on this thinking it was a Minecraft build lol
😂😂was it of any use?
Thought it was mine craft
স্যার আমি কি আপনার মোবাইল নাম্বারটা পেতে পারি
Have BoQ
you have the boq?
can you send me this via pdf if possible
I need some help.
Can I contact you??
3500 liters underground water tank ki labour kitni honi chahyey