Hello, I just change my aqualink rs8 board now spa drain in spa mode, I check my valves working it’s not valve problem can you please help me to fix it?
I need help! All buttons turn on except for AUTO, SERVICE, and TIME OUT. Also, filter pump and blower are off! No circulation and my pool is green. Please help!
Hello there! Can you link the part for the actuator and relay for this model? I have the same model and can’t seem to exactly see what the actuator looks like, if it’s just the 3 on connector or the entire wire. It’s easier for someone like yourself to link what I need so I can swap it. Thank you! Ps: also the relay too! Thank you
Thank you Sir! You just saved me more than $2000 the pool guy wanted to charge me for a new RS6 motherboard. I checked the fuse and sure enough it was blown! 5 bucks and two minutes later and everything is working again!!! I’m so happy right now! Awesome video…thanks again!
Thank you...very helpful. I have an actuator the when i flip it on, it continues to blow the fuse. Should these need to be replaced in 4 years with fairly limited use?
Craig, Can you please do a RUclips video on why a Pentair pool heater would backfire. And how this can be fixed. Can't find anything on line and I'm looking for solutions. Let me know if can or cannot be done. Thank you!
I have a question I have the same jandy controller your showing in the video and also the jandy PDA for that controller. My pda will not keep the correct time at all . I have replaced the battery’s and as far as can see that is about the only thing you can do. Is there anything else I can do to fix this problem. Thank you
There is a 2032 clock battery on the back side of the board. If you replace that battery with a known working one and it still doesnt show the correct time then the clock chip on the board is bad.
Link to purchase the part from the video - amzn.to/4bKnBNp
theres an error on the link
@@nealburgner8816 Thank you for bringing this to our attention. We have edited the comment, and the link should be working now.
You are awesome thank you for the video you helped me figure it out
Hello, I just change my aqualink rs8 board now spa drain in spa mode, I check my valves working it’s not valve problem can you please help me to fix it?
I need help! All buttons turn on except for AUTO, SERVICE, and TIME OUT. Also, filter pump and blower are off! No circulation and my pool is green. Please help!
Perez Michelle Jones Frank Harris Kenneth
What if the fuse is good ?
Hello there! Can you link the part for the actuator and relay for this model?
I have the same model and can’t seem to exactly see what the actuator looks like, if it’s just the 3 on connector or the entire wire. It’s easier for someone like yourself to link what I need so I can swap it. Thank you!
Ps: also the relay too! Thank you
Thank you Sir! You just saved me more than $2000 the pool guy wanted to charge me for a new RS6 motherboard. I checked the fuse and sure enough it was blown! 5 bucks and two minutes later and everything is working again!!! I’m so happy right now! Awesome video…thanks again!
Thank you...very helpful. I have an actuator the when i flip it on, it continues to blow the fuse. Should these need to be replaced in 4 years with fairly limited use?
Thanks for the help, was getting ready to call an electrician.
What if I don't get 25 or 26? Does that mean that my transformers burnt out?
Craig, Can you please do a RUclips video on why a Pentair pool heater would backfire. And how this can be fixed. Can't find anything on line and I'm looking for solutions. Let me know if can or cannot be done. Thank you!
my aqualink has no power but it keeps on making clicking sound, but not lights.
Is it likely a blown fuse if both the outdoor and indoor Jandy controllers units out ?
Thank you.! This helped me, and let me sleep better, cause I thought the board got fried… appreciate it.!
I have a question I have the same jandy controller your showing in the video and also the jandy PDA for that controller. My pda will not keep the correct time at all . I have replaced the battery’s and as far as can see that is about the only thing you can do. Is there anything else I can do to fix this problem. Thank you
There is a 2032 clock battery on the back side of the board. If you replace that battery with a known working one and it still doesnt show the correct time then the clock chip on the board is bad.
Can you link the fuse again, please. Just went to purchase and said it couldn’t be found! Thanks in advance!!! Appreciate all your help!!
Thank you for bringing this to our attention. We have edited the comment where it is linked, and it should be working now.