Full restoration high pressure air compressor engine - Restore large capacity air compressor
HTML-код
- Опубликовано: 30 сен 2024
- Full restoration high pressure air compressor engine - Restore large capacity air compressor
Thank you for watching the video. Please share your opinion below in the comments section. Don't forget to like and share the video. Have a nice day
#restoration
#restorationvideos
#dtrestoration
SUBSCRIBE: / @dtrestoration8590
There is so many things wrong with this video. No new parts. The bearings in the 3 phase motor... just replace them.. but then dont hammer on the outside races. You can HEAR how bad those bearings are now when they powered up the motor.
Nothing was replaced, nothing was refurbished. The teflon tape was backwards in half the shots, then there was teflon put onto the clamp nuts for the air lines.. they dont even hold air pressure. This was... terrible. The motor sounds horrific. The sounds it was making are the sounds you hear when you should be replacing the bearings PROPERLY. Yea, this was terrible. They didn't tighten the belts. The preload adjustment on the compressor bearings... which were assembled dry..... no overpressure valve... reciever not tested... the list goes on. I wouldn't have this thing within 100 meters of me.
I love when they paint bolt threads or when they put too much teflon tape and backwards ahhahahaha so beautiful.
@@MrJosevintem And not even a grounding, absolutely life-threatening
ボルトの締め方が素人。部品洗浄不十分。ピストンにシリンダーを入れる時、シリンダー内側に潤滑油を塗布して欲しかった。
最低限の部品交換は必要。
モーターのベアリング洗浄後、回転させガタツキを何故、確認しない⁉️
モーターの電源コード通す穴に保護のゴムブッシュは付けない⁉️
モーターのベアリング駄目じゃん。
Falta muito detalhe, não limpou os pistão, não trocou os anéis, não bruniu as camisas, não limpou( lixou) a ponta do eixo onde coloca a polia( volante), não lubrifica as camisas para montagem, não gostei nota 4
حتی بیرینگهای مخروطی دوسر شافت عوض نشدند،یاتاقانها تعویض نشد،ودرکل همه راشست ومجدداََ مونتاژ کرد وفقط شد کمپرسور رنگارنگ 🤔🤔🤔
I have to disagree here - restoration means to restore back to new, NOT just strip down, paint everything then rebuild as a lot of these "Full restorations" do. This has done absolutely nothing except make it look pretty. I saw the cylinders were still rusty, the crank journal was rusty, same bearings re-used, same piston rings re-used, pistons rusty - in fact nothing was restored except the gaskets and changed the oil. For what good this has done there was no need to strip it down, he could have just painted it assembled.
Show um,,partner,,,,Show them.
@@larryclifford8928 He's totally right, this did more harm than good, not only they didnt replace anything, but painted on the races, studs and the bore too! They replaced 1 seal, but then they use that gasket material that is used to make shoe soles and will start to leak in a couple of weeks use.🤣 Was a good vid though.
Да им пох на нас, на Вас и на этот компрессор😅
@@interesting7906 I’ve seen dry engines run before. So much damage is done until the oil reaches each moving part. Assembly lube is very important. I give the guy credit for getting to run.
Looks like one of those shops in India or Pakistan. Painted all the surfaces that should not be painted. Didn't ever rebuild the valves. In the old days we used those compressors in hospitals. We would tear them down every six months. Once you clean them up if the springs are still good you can flip the valve plate over and use them again. We would replace rings and valve assemblies annually. I might use that gasket material on a LP steam line but not on a compressor.
No washer on wheel axle, split pin not properly fitted. Air receiver welded and not pressure tested (or safety valve). But the biggest sin is no gland fitting on the motor or electrical boxes! 3 phase wiring going through a hole with sharp metal edges. A air compressor on wheels will shake a lot and it will not take long to ware through the insulation and kill soneone!!!! bad news
Thank you!!!
Yep, and the banging on the outer race of the bearings, ouch.
Why not paint it better when all that effort is made?
The motor sounded really bad, or what was that noise when only the motor was spinning?
Would be nice with a pressure test of tank, we don't know how rusty the tank is, or if the safety valve even works.
And last, it's going to overheat because no fan for cooling the cylinders.
Unfortunately just a another "youtube-paint-it-video" 😢
all the electric is really bad.
he has no clue what he is doing.
Cái này là dành cho mấy bạn thích màu mè, và không biết gì về máy nén khí xem ^^
What I would call 'asian redneck' -style. Wearing dress shoes while spray painting, the dog getting high on paint fumes, and nothing other than a bad paint job was done to the compressor which will work just as good or bad as it was before. 🤣
Piece of krap in (re-built, WTF ?? ) Piece of krap out......
Paint on shit equal clean shit just like in the navy...
Sounds like an old coffee grinder. Sorry, bad work.
Total botch, sealing surfaces painted over, old piston rings left in, electrical connections swapped, screw connections not tightened properly, and above all, cuts on the boiler that were too deep when removing the carrier plate. Useless work and a waste of time.
Why even start it. No pre lube on ANYTHING. No torc wrench on the cylinders or piston rod bolts.
Worse than a "sloppy so called restoration" is the assembly procedures. Who in their right minds pounds on bearing using the outer race over a shaft. That is OK if you are putting them in a recess but totally wrong for installation on a shaft. I never saw the tank being pressure tested. If it was really rusty on the inside it might fail under pressure. Compressed air is much more dangerous when it fails as compared to a hydro test.
Wtf kinda tig spot hip hop pop and lock weld job was that?
Didn’t replace/restore anything other than a good clean up really. To the inexperienced eye might look nice, to anyone that actually repairs stuff they see right thru this.
And why do a lot of these restoration channels paint stuff to look like kids toys using bright as colors? Put a nice industrial/machine tool grey/silver on it and it’ll present much better IMHO at least.
But seeing as he was able to take it apart correctly and assemble properly, for the most part, I’m sure he knows enough how to actually restore it properly if he wanted to and it wasn’t just for a video. So I’ll give it a B+. Better than the average person would probably do not excellent work though! 🤷🏻♂️
Wasn't even a good cleanup! Very sloppy job all around. Made it look like a toy with all those silly colours! And didn't show in the end that it even filled with air!
This not a restoration, just a clean up and paint job.
The biggest mistake is no inspection or testing of pressure vessel and associated pressure relief valve. If no valve fitted as original a suitable valve should have been installed. Very poor show.
Wtf man ? Put back the old barring ? Noooooo
Questa NON È un revisione! È solo un restauro estetico, anche venuto male visto la qualità schifosa della verniciatura, nella cura dei particolari e nell'uso di tecniche per ottenere un risultato decente.
Il compressore è stato rimontato così com'era senza un controllo accurato delle parti soggette ad usura e la pulizzia delle parti interne è stata molto carente. Il motore elettrico è "l'apoteosi della vergogna": i cuscinetti non sono stati controllati, dovevano essere sostituiti; infatti quando hanno provato il motore (ovviamente dopo il cosiddetto "restauto"😩) si è sentito il rumore tipico di cuscinetti ormai con la vita finita☠. Non aggiungo altro. VERY BAD!
Já li alguns comentários,está tudo dito,nunca vi tamanha inconsciência no que está a faser,nota 2para as juntas e pintura,esse Sr devia de ter vergonha de mostrar um vídio desses.
you need to use oil when you reassemble
Thank you, watching video!!!
No need to bother when you are going to put the bearings back together with paint all over the races and are not going to clean gasket surfaces from paint before assembly. It may work for a while but has been life limited by poor assembly.
that motor sounds not happy, probably the way the bearings were installed. I would of tapped them down on the center race not the ou side of the bearing. it sounds like the bearings are not seated
This was just so wrong, I’m speechless.
Nada profissional.
Montou as rodas sem colocar as arruelas dentro e fora das rodas.
Montou o motor sem um pingo de óleo na montagem.
Ou seja.
Pode até saber das coisas mais profissional com certeza não é.
Nota zero pra ele.
E sem falar que pintou o compressor sem lixar.
Só usou a lixadeira...
Fraco esse Jaspion das antigas.
Kkkkkkkk
Sure... just take everything apart, wash it in diesel, then spray it all as colorful as possible and put it back together. It doesn't matter that the rusty cylinders and old rings remain, the more colors, the merrier.... Videos are really made by everyone who has a hole in their ass. :))
That was total waist of work you did, this "short fix" will not last, with this kind of work you loos followers..........
BENDE USTAYIM İŞÇİLİĞİNİZİ BEENMEDİM YAĞLANAÇAK YERLERİ YAĞLAMADAN TAKIYORSUNUZ BUNU SİZE YAKIŞTIRAMADIM
Hmm.. @1:43:30 the sound of chipped bearings, yay.. Maybe @1:31:25 you could have reinstalled them without hammering the outer race around.. use a tube on the inner race and a press.. I'm sure you could make a press with the stuff you find.
修理屋ではなく塗装屋です。修理目的ではありません おもちゃ色に塗るためだけの分解です。修理のスキル有りません(We are a paint shop, not a repair shop. It is not intended for repair; it is only disassembled to be painted in toy color. I have no repair skills)
I would like to know did the compressor work? I see the motor run,,,yet did the compressor itself do what is was built to do?
Vô nghĩa chẳng làm gì ra hồn vòng bi mà đóng vòng ngoài là không biết làm rồi hơn nữa cắt miếng đệm quá vụng về
Do not hit the outer race when driving the bearing.
Let's hit the inner lace
What a crappy job. Restoration?? No way.
This is a repaint not a restoration.
Tipo de video que não se aproveita nada!
POR SEGURANÇA DEVECE FAZER TEXTE HIDROSTATICO DO RESERVATÓRIO.
Incredibile. ,non ha sprecato neanche 1 ml di W40 per sbloccare una qualsiasi vite o perno!!
In compenso ha abusato del martello !!
Это видео уже было на другом канале неделю назад
'restoration' is hyperbole, 'full restoration' is just a lie.
IS NOT RESTORATION IS ONLY CLEANING AND PAINT 😬😬😬
Rapaz, pintar primeiro pra depois soldar, mel delz!! Isso foi a porquice do século!!
But does it work?
This is a comprehensive video of what NOT to do 😔
assembly of orange wheels without washers? weld painted things 🤦 In that case, you need to weld the brackets, sand and paint and then use screws or rivets for the joints...🤦 I'd rather not watch because I don't want to see what they'll do with the engine.. 🤦
Szép a festés. De a felújítás nem csak ebből áll! A gépi megmunkálást szerettem volna látni! 😡
For what good this has done there was no need to strip it down, he could have just painted it assembled.
You didn't install washer on wheels, the stopper will broken.
Machined surface such as cylinder or threads, shall not be paint to avoid leak failure. and pets should keep clear out of the factory while painting, and welding should keep clean, to be free of dirts,dusts and paint, or weldings to be done before painting, and lubricants as grease should apply during pulley and shaft assembly.
This is a very bad way to mount the ball bearings on the rotor. Il is needed to apply the force on the inner, but NOT on the outer. Now the ball bearings are out of order and noisy as the test shows. It need to be remplace ball bearings for a long service.
What is the top speed? 🚆
Encore un mécano "fantoche" les roulements sa ce change et surtout ont ne les frappes pas car il sont marqués sur le chemin de roulement et donc "HS" a bon entendeur !!!!
You didn't install washer on wheels, the stopper will broken
Looks like that compressor has been commissioned for COCO the Clown and his clown car workshop 😂
The hole video is a wery big scam
オイル潤滑のコンプレッサーはシールなしの開放ベアリングが普通なんだけどな。
You blinding me with those awful colors!
Well you really don't know how to use a tig welder do you? You weren't stick welding lmao
Hat sich eigentlich irgendjemand den Kessel von innen angeschaut? Der wird von innen noch verrosteter sein, als von außen. Druckkessel !!! Ich möchte nicht in der Halle, geschweige in dem Raum sein, wenn der dann doch "hochgeht" (Zumindest fliegen dann frisch lackierte Stahlstücke durch einen hindurch....
Рестоврация для музея😂, а не для работы.
Не надо писать что ресторация обойму конусного подшипника не красят и в старые литол не кладут да ещё и на двигателе барну перекручивают за кадром камутация треугольником была а потом вдруг звездой стала
Has anyone seen this damage on the tank when they cut off the base and why didn't they sand it and check the pressure? Why weren't new pistons and rings installed, no one retracted the cylinders, and the old corroded valves are a joke!!!
ベアリング圧入で外輪側を叩いちゃダメでしょ。
あれだけで転動面のダメージ有るでしょうね。
Piston rings, bearings and bushes need to be replaced otherwise you’ll have problems
What the hell? I didn't see any engine.
I was expecting to see a combination engine/air compressor. (there is such a thing)
There's a big difference between an engine and a motor.
Low quality restoration
Country of Taiwan or China ?
What chemical's or detergents do you use to wash the parts
I think the temperature of motor is very high when running
Eso no es una restauracion oara pintarlo y cambiarle el aceite no necesitaba desarmarlo
Una restauracion es canbiar los anillos metales baleros reacondisionar cabezal ETC, ETC .QUE DESEPCION
Como que vi unos cambios en la conexión electrica😂
yellow, blue, black,orangeand gold different color i like it😍😍😍
You did a good job, but when you put the pieces in place, you didn't put them in the right place(washer)
Fraud channel just for clicks🤣🤣🤣
Co to za regeneracja jak wszystko złożone na starych częściach, nic nie zużyte. Słychać jak huczą łożyska w silniku, ciekawe czy wlali nowy olej do sprężarki czy ten stary.
Devilbis Made in France
Alternate titles:
-Birth of the worlds first Anime Air Compressor
-Clown Compressor Compendium
-Bad Bearing Bonanza
-Paint a Pig and Call it A Pork Chop
All of these would be a better description than "restoration"
Totally pointless "Re-build" I stopped watching at the so called " cleaning" process. Them gave it a thumbs down, which is probably the first one in two years of avidly watching RUclips for at least four hours a day seven days a week.
このコンプレッサー売物じゃないよね?w
Ông ấy không có đồ nghề, chỉ có cái mỏ let răng mà làm vậy người chủ của nó có hài lòng không làm vậy mà cũng lên mạng được hả
hello men, where you forgot WD40???
Ich hoffe Ihr habt daran gedacht, die Zylinder mit Hitzefester Farbe zu lackieren ! wird sich sonst verfärben 👆 werden heiß 🔥( Auspuff od Ofen Farbe nehmen)
So a full restoration is stripping, cleaning, let someone who is color blind choose the color scheme and paint it, then put it back together again with all the same worn out parts and not pressure testing the tank.
ballbearings no goods
Bravo god video, men sir de lavet nogle slemme fejl men ellers ok.
Painting over those surfaces was a pretty rookie looking thing to do, as was using a. claw hammer to cut that gasket material.
Using a hammer to cut gaskets is not a novice way to do it. I've watched many mechanics in business for decades use this technique. It's actually a pro move. He should have cut all the way through the gasket with the hammer, and then he would have not needed the scissors for the cylinder bore. A ball pein hammer is more effective, and he should have spread the RTV in the middle of the gasket, not the inside edge.
Welding over paint is not a good practice. The welding should have been done before the painting, then the welds wont rust as quickly.
السلآم عليكم تحياتى لك من المغرب اتمنا لك الازدهار
ไม่ใด้ใส่แหวนปิดล้อก่อนใส่สลักกันล้อหลุด
It is strange that so little was done to repair the unit. Perhaps it was just to present it looking better. I don't know.
Thats not a high pressure compressor
I notice when fist started the motor was connected in delta and now after restoration its connected in star is there a reason for this
Unless he removed the paint from the sealing surfaces of the cylinder and head, what was he thinking.
I have been a mechanical engineer for 40 years and never ever stripped a 2 r s bearing re greased and refitted, always replaced said bearings,
Доктор Дью уже все сказал за меня, насчет вот таких реставраторов.
39:56 tu trzeba małego młotka ale o końcówce w kształcie kulki, wtedy uszczelka się sama odcina i jest gotowa
Good very good
L'accoppiamento dei colori è un pugno in un occhio. Mi sa che i cuscinetti del motore sono andati.
=Jepara 1
피스톤링. 압축링은 바꿔줘야지 그렇지 않으면 수리할 이유가 없는데. 베어링도교체하고
It looks like Dad needs to teach his son how to paint. I'm guilty also, Dad needs to wear earplugs and a dust mask. Love video. John H, Minneapolis, Mn
renew timing bomb
As long as it works when done , who cares iwhat it is called
Nice restauration, but the belt guard is still missing.