😀Thanks for watching! Here are some other RAM videos you might be interested in! Change the oil on a dodge ram 3500 ruclips.net/video/MEiKe8ZKBO0/видео.html Change the front brake pads and rotors 2018 Dodge ram 3500 Duely ruclips.net/video/o7f7HjkrOqU/видео.html How to change the Air Filter 2015 Dodge ram 1500 ruclips.net/video/D47OTKT--GA/видео.html 2009-2018 Dodge Ram Transmission Fluid & Filter Change ruclips.net/video/QReFPez1njw/видео.html
Did this today. PSI was showing 96-98. Got the tools needed and changed it myself. Took a min, due to all the hoses being hot. After the change, psi is between 28-35. Thanks for the video
@@ashleypinnekins5812 Any auto parts should have it. Autozone is where I got mine. It was super simple to change the sensor out, knowing ahead of time how to manipulate the plastic latch on the e connector surely helped out too. My chk engine light stayed on for a few more start cycles, I think the next day is when it actually turned off.
My oil pressure in 2012 1500 drops to 20psi even a bit lower when idling and high 30s-low 40s when driving. It has 220k miles, any idea what it could be? I get oil changes done with a mopar filter from autozone.
After changing my battery yesterday this morning I noticed for a brief second the oil light came on with a reading that said low oil pressure. I took a look in the dash computer and it shows no oil pressure. Can you help me figure what’s going on?
Is the sensor for the gauge a different part number than if I had just a warning light (base cluster)? I swapped in an upgraded cluster with a gauge and my pressure gauge is not working.
Would an overtightened sensor cause the sensor to not work properly? Or are we more worried about damage to the threads in the block? I’m dealing with this now and I definitely tightened mine too much. The truck does not start. Click but no rotate. Scanned P0520 and P0522 codes, both point to oil pressure sensor. Would a drop in signal from the oil pressure sens trigger a fail safe in the CPU that won’t allow the engine to start?
Just curious. You mention the importance of not putting too much pressure when screwing it back in. Is there a good reason not to use a torque wrench to ensure you don't over-tighten it?
Man I am having the same issue I already replaced the sensor might replace it with the Mopar one. Crazy thing is my oil psi is in the 30s high 20s on idle
I did all this to correct the check engine light and oil pressure and had the diagnostics for the code to confirm this exact issue I installed the part and turned the engine on the oil pressure is near perfect now but the check engine light is still on .anything that might make this into another issue?
Would a bad oil psi sensor cause your engine to sound any different? Around 4-5k rpm, it feels slightly sluggish and sounds like I can hear the motor instead of the exhaust if that makes sense...
@@svgjewno4850 after reading this 1 year old comment, I have no idea what the he'll I was trying to say here 😅. But I did change the sensor. Sold the truck recently.
Bronco im in the same boat right now. 2012 5.7 Hemi, 170k miles, chk engine light just came on a few days ago and Autozone said its the oil sensor. The truck runs a bit sluggish now and it does sound different at higher rpms, just as you explained. I have a cold air intake, and it makes the engine sound like a 4 barrel carb but that sound is kinda gone right now. I have a hard time believing the oil pressure sensor is gonna make it run any better, but I'm doing the sensor chg today.
@@majorrev8690what is your oil pressure reading at? Mine was maxed out. New sensor fixed that. Also, when I traded it in, the dealer told me it had a misfire.
@@303ant420 My dash doesn't show the oil pressure, so I cant say. I wish it did. First vehicle ive owned w/o a full arrangement of gauges. Im more worried about how its running right now. With the cool fronts passing thru, I usually make peak hp. But right now its a dog for some reason.
I recently replaced my oil sensor on my 2016 ram 1500 ssv 5.7. Got my oil changed yesterday and check engine came on. Plugged my scan tool up and it's the same code as before P0520 .. idk if I bought a bad sensor or if it's more serious problems. Truck only has 104k miles. Oil changes have not been neglected and I use synthetic every time. Any suggestions 🤔?
@@Michael123-p3f Hmm, I would try checking to make sure that it is not clogged and try a new sensor too. My thoughts are there is probably a fault in the sensor.
AutoZone $11 OPS socket just for this application! Deeeep socket! My friend said good investment because sensor is crimped metal to plastic and will fail eventually and repeat! I replaced OPS in new acquired truck. Seller Installed with channel locks, damaged , leaked!
This code that you have is similar to what we experienced, the sensor in your case is it reading at zero pressure or at max pressure? A majority of the time replacing the sensor will remedy the repair, there could be other electrical gremlins but these are less likely.
Holy cow man I never seen someone manage to turn ; pushing the red plastic safety release tab out, from the flat end,depress electrical connector release tab and remove…. Elaborated upon to an extent That was so ridiculous and psychologically torturous to a mechanics ears that it was downright impressive. But painful. My god are people really that horrendously ignorant that it’s necessary to elaborate to that extent regarding the red release clip/electrical connector???!! 😂
You should listen to the Revit Auto en Espanol channel! What I realized as a content creator is that a majority of the people watching our videos have never held a screwdriver. So the over explanation of every single step helps these people get through it. I get it as a mechanic if I was to explain to you this job I could tell you what to do in 2 sentences. That is mechanic to Mechanic ;) If you want to help us help more people :) We are hiring! Painful over explanation required :)!
It is a REALLY BIG Ratched :D Or a Breaker bar with a ratcheting head :D! Come follow me around for a day and have your brain explode with everything I miss label :D! One of my closest Friends Colin does this to me all the time. I think it helps me be a better communicator :D! I sincerely Appreciate you, thank you for the laugh this morning! Happy Motoring-Blair
I will leave it on thanks, been wearing these since before the pandemic, and I will wear them after. Keeps the wind off of your face and your neck. Helps when you work outside all day and your brother already has skin cancer. Also helps when it's cold out....
It's really cold outside while filming this so it keeps my neck, ears and face warm. It also says my company name, which I would not call a gang :)! Thanks!
😀Thanks for watching! Here are some other RAM videos you might be interested in!
Change the oil on a dodge ram 3500
ruclips.net/video/MEiKe8ZKBO0/видео.html
Change the front brake pads and rotors 2018 Dodge ram 3500 Duely
ruclips.net/video/o7f7HjkrOqU/видео.html
How to change the Air Filter 2015 Dodge ram 1500
ruclips.net/video/D47OTKT--GA/видео.html
2009-2018 Dodge Ram Transmission Fluid & Filter Change
ruclips.net/video/QReFPez1njw/видео.html
I really appreciated his thorough explanation, and the young man did not try to rush thru it. Thank you.
Glad it was helpful! Don't forget to like and subscribe for more helpful tips/repairs!
Did this today. PSI was showing 96-98. Got the tools needed and changed it myself. Took a min, due to all the hoses being hot. After the change, psi is between 28-35. Thanks for the video
Great instruction. Hes not kidding about oil leak from this hole. The old one dripped two quarts a week! Good thing i check oil level often
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
Thank you sir, I almost freaked out this morning, when I noticed my oil pressure was extremely high, I looked you up. On RUclips 😅Now I can fix it!
,
You can imagine our surprise when we started the truck and ours said zero! ;)!
Glad this video helped!
-Blair
Thank you for this. My check engine light came on and the test said it was the oil sensor. I am going to switch it out tomorrow.
HECK YES! Let me know how it went!
Where do you get the part?
@@ashleypinnekins5812 Any auto parts should have it. Autozone is where I got mine. It was super simple to change the sensor out, knowing ahead of time how to manipulate the plastic latch on the e connector surely helped out too.
My chk engine light stayed on for a few more start cycles, I think the next day is when it actually turned off.
great video! the info of bringing up the oil pressure on the truck display is huge! Thank you..
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
How much oil will come out? do I need to drain oil before replacing sensor?
Me and my buddy are doing this now. So far so good!
Great to hear! How did the repair finish up for you guys?
Unrelated to the pressure switch! Lol
@@contractor556 O man! What was the problem?
@@Revitauto misfiring issues, lifter tapping, the guy checked the newt changes oil and it had a bunch of metal in it…
Good enough for my 'like and subscribe'! Your how too lesson is appreciated! 👍
Thank you!
My oil pressure in 2012 1500 drops to 20psi even a bit lower when idling and high 30s-low 40s when driving. It has 220k miles, any idea what it could be? I get oil changes done with a mopar filter from autozone.
Very precise clear tutorial - 🙌🏽
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
@@Revitauto - I Subbed one year ago *
I see, thanks! @@dimensionexo.
This was really well done. Thanks
Thanks! Happy Motoring!-Blair
Same color 2012 Ram I have - Tequila Sunrise...
After changing my battery yesterday this morning I noticed for a brief second the oil light came on with a reading that said low oil pressure. I took a look in the dash computer and it shows no oil pressure. Can you help me figure what’s going on?
To add, no check engine light is on.
Thanks for the info. Great video
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
Is the sensor for the gauge a different part number than if I had just a warning light (base cluster)? I swapped in an upgraded cluster with a gauge and my pressure gauge is not working.
Would an overtightened sensor cause the sensor to not work properly? Or are we more worried about damage to the threads in the block? I’m dealing with this now and I definitely tightened mine too much. The truck does not start. Click but no rotate. Scanned P0520 and P0522 codes, both point to oil pressure sensor. Would a drop in signal from the oil pressure sens trigger a fail safe in the CPU that won’t allow the engine to start?
The switch was leaking oil on my sons truck,bout to get the part tomorrow
Thank you for the excellent video!
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
My oil pressure is reading 86 but my check engine light is not on. Is the the problem?
I have a 2006 Chrysler 300C v8 5.7 l and i oil pressure up to 50 then if I accelerate at time I low power and oil pressure. What could be the problem
Just curious. You mention the importance of not putting too much pressure when screwing it back in. Is there a good reason not to use a torque wrench to ensure you don't over-tighten it?
torque wrench won't be accurate once you attach extensions. their will be too much slack and give in the all the connections
Man I am having the same issue I already replaced the sensor might replace it with the Mopar one. Crazy thing is my oil psi is in the 30s high 20s on idle
Great video thanks
Glad you enjoyed it
Is oil temperature sensor same procedure? 1 1/16?
You are a wonderful person. Will you answer my question?
Thank you for the help
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
I did all this to correct the check engine light and oil pressure and had the diagnostics for the code to confirm this exact issue I installed the part and turned the engine on the oil pressure is near perfect now but the check engine light is still on .anything that might make this into another issue?
I have the same issue. Oil pressure is at 48. So idk why the check engine light isnt shutting off
Have you tried clearing the code after the new install?
@CoreyP after driving around for a bit it self corrected and stopped showing after a about 20 miles of driving
Thank you.
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
I have an 08 grand cherokee with a 5.7, is it in the same spot?
Thank you
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
I’m pretty sure it threads into iron at least, there is an aluminum oil cooler that sits below it though 👍
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
Does slot of oil come out ? Also should I add some after installing it?
I’m getting ready to do this. Would hand tightening be fine?
How did it go?
Cool
Glad you liked the video! Happy Motoring!-Blair
Is this on the 3.6 l vvt
All I got is a crescent wrench and how much oil did you lose
Would a bad oil psi sensor cause your engine to sound any different? Around 4-5k rpm, it feels slightly sluggish and sounds like I can hear the motor instead of the exhaust if that makes sense...
No
@@svgjewno4850 after reading this 1 year old comment, I have no idea what the he'll I was trying to say here 😅. But I did change the sensor. Sold the truck recently.
Bronco im in the same boat right now. 2012 5.7 Hemi, 170k miles, chk engine light just came on a few days ago and Autozone said its the oil sensor. The truck runs a bit sluggish now and it does sound different at higher rpms, just as you explained. I have a cold air intake, and it makes the engine sound like a 4 barrel carb but that sound is kinda gone right now. I have a hard time believing the oil pressure sensor is gonna make it run any better, but I'm doing the sensor chg today.
@@majorrev8690what is your oil pressure reading at? Mine was maxed out. New sensor fixed that. Also, when I traded it in, the dealer told me it had a misfire.
@@303ant420 My dash doesn't show the oil pressure, so I cant say. I wish it did. First vehicle ive owned w/o a full arrangement of gauges. Im more worried about how its running right now. With the cool fronts passing thru, I usually make peak hp. But right now its a dog for some reason.
If you do not change right away could this harm the engine
You’re the best thank You!!!!!!
No way! You are the best! Thank you for watching and commenting! Make it a great day!
Should my check engine light come off right away ?
Is this the same as the oil temp sensor?
I recently replaced my oil sensor on my 2016 ram 1500 ssv 5.7. Got my oil changed yesterday and check engine came on. Plugged my scan tool up and it's the same code as before P0520 .. idk if I bought a bad sensor or if it's more serious problems. Truck only has 104k miles. Oil changes have not been neglected and I use synthetic every time. Any suggestions 🤔?
Interesting, what is the gauge reading on the dash? Where did you get your sensor from?
@Revit Auto it reads 99. If I unplug sensor it reads 90psi. Bought sensor from Amazon. I think it's a Dorman
@@Michael123-p3f Hmm, I would try checking to make sure that it is not clogged and try a new sensor too. My thoughts are there is probably a fault in the sensor.
@Revit Auto my dad reordered another 1. This seems an on going problem for this truck but I'll try new sensor and see what happens
I changed the sensor on my hemi charger but light still on and reading at 99 psi but car seems to run very normal
My ram1500 doing same thing. I replaced the sensor less than 2 months ago. Worked fine and read normal psi. Now it's doing same thing 99 psi.
So this sit a $470 job that I was quoted today?
By chance you wouldn’t be located in the DC area would you?
Perfrct instructions
Glad it was helpful. We would appreciate it if you subscribed to help us grow and continue creating repair videos to help everyone. Happy motoring!
Can this sensor cut your fuel off if you run low on oil?
I dont think so, this was showing no oil pressure for a bit and the truck was still running. Have you found anything out yet?
Hopefully I tightened it enough. I can still see half the threads and no leak. Reads perfect now
Awesome! I am really glad to hear that its all working out ok! And we had lots of threads showing too! It is better to not over torque it! Great job!
En español
@@armandopalacios5239 Hola Armando, aquí tenemos el vídeo en español. Espero que le ayude!
ruclips.net/video/yLzijnXe0mE/видео.html
What if oil don't come out
Is the socket 1/16" or 1 1/16"
It is a big Socket! I am not sure if there is a 1/16" socket out there! Would be pretty little! Happy Motoring! Let us know how you did on your truck!
Just use common sense its a big socket
AutoZone $11 OPS socket just for this application! Deeeep socket! My friend said good investment because sensor is crimped metal to plastic and will fail eventually and repeat! I replaced OPS in new acquired truck. Seller Installed with channel locks, damaged , leaked!
Is this for p0935 code
This code that you have is similar to what we experienced, the sensor in your case is it reading at zero pressure or at max pressure? A majority of the time replacing the sensor will remedy the repair, there could be other electrical gremlins but these are less likely.
Holy cow man I never seen someone manage to turn ; pushing the red plastic safety release tab out, from the flat end,depress electrical connector release tab and remove…. Elaborated upon to an extent That was so ridiculous and psychologically torturous to a mechanics ears that it was downright impressive. But painful. My god are people really that horrendously ignorant that it’s necessary to elaborate to that extent regarding the red release clip/electrical connector???!! 😂
You should listen to the Revit Auto en Espanol channel! What I realized as a content creator is that a majority of the people watching our videos have never held a screwdriver. So the over explanation of every single step helps these people get through it. I get it as a mechanic if I was to explain to you this job I could tell you what to do in 2 sentences. That is mechanic to Mechanic ;) If you want to help us help more people :) We are hiring! Painful over explanation required :)!
Breaker bar? Looks like a ratchet lol
It is a REALLY BIG Ratched :D Or a Breaker bar with a ratcheting head :D! Come follow me around for a day and have your brain explode with everything I miss label :D! One of my closest Friends Colin does this to me all the time. I think it helps me be a better communicator :D! I sincerely Appreciate you, thank you for the laugh this morning! Happy Motoring-Blair
Took my truck to auto shop, the mechanic didnt wear a mask, i demanded that my engine not be infected with his germs!
Ecu has a virus if he didn't wear a mask
Y'all never seen a Gaiter before and it shows.
@@Revitauto Mister, this old Missouri county boy would eat a Gator & make boots out of its b
Lol weak hands
Since I spend so much more time in the office my hands are so incredibly weak!
Redo this and take the diaper off.
I will leave it on thanks, been wearing these since before the pandemic, and I will wear them after. Keeps the wind off of your face and your neck. Helps when you work outside all day and your brother already has skin cancer. Also helps when it's cold out....
Why is he wearing a bandana? Is he in a gang or something?
It's really cold outside while filming this so it keeps my neck, ears and face warm. It also says my company name, which I would not call a gang :)! Thanks!
@@Revitautoah ok. It doesn't look cold, your breath is not visible and the truck says 54° which is relatively warm.