That was life changing for me. I’ve had my fair share of carby issues in the past as we all have . I’ve always been told not to touch them because they are too complicated . But your tutorial made it look and sound easy. Thank you so much.
Thanks man. I got same with a aluboat, buster. Watching this, it was pretty easy job. Next time, when proper shop is near, I also put 45 jets. Now only cleaning. I had minimum tools available and no pressurised air. But works now.
Love this, I didn’t change the carbs and my motor ran like a charm after that, I might change the jets one day though. Thanks man this really helped with assembly and re assembly 👍👍
I really want to thank you for giveing this advice my 40hp jet drive was really hesitating but i went an got some torch cleaning bits and drilled my jets to the next size of drill bit size its now running like a champ thank you somuch keep doing what your doing your real helpfull!!!!!!!!!!!
This is great. Thank you very very much, from France. I have the exact same engine (2007) and between 2000 and 3000 it's very difficult to get the power and sometimes the engines is simply stopping. Your video is perfect, and I will do the same soon. Best regards. Philippe
FYI, you can get those O-Rings for 49 cents a piece if you go to a hard ware store that sells them individually. I just bought 10 at the Do-It-Best Hardware store down the street from my house when I rebuilt a set of carbs on my Merc 50hp.
nice i want to get a four stroke engine but i live on a island where we dont have a service center. you should do a video on how to care for the engine like things you should on a regular basis
I'm replacing the accelerator pump belows on my 2000 mercury 40hp 4 stroke. It has the same yamaha powerhead and carbs. How do I remove the accelerator pump rod without breaking anything?
great tutorial! will probably do this this weekend. just one question do you need tinker on that brass fuel screw? Mines been idling very rough like it feels like 1 cylinder off onidle but goes fine on wot
I am going to attempt to rebuild my carbs 2001 50hp yamaha, F50TLRZ have the exact same problem you had. Carbtuner comes this week and was going to order 4 carb rebuild kits. Seems like there is an upgraded kit from the original. 62Y-W0093-11-00 new kit from old kit 62Y-W0093-10-00 hope it has better jets or something in new kit. Also did you adjust the air mixture screws on carbs?
I have a 1999, F100, Yahama. Idle sneeze and trouble through 2-3k range. Had the carbs cleaned a couple times, nothing fixes it! Any input on a jet change for that?
Hey man I know this is a old video but hoping you had a recommendation for jet upgrade size on the old mercury 4 stroke 90 elpto, it's terrible about clogging constantly. Thanks
Your putting in jets from a small engine? Is that correct? Also I have a leaking float seal on the top carb, do I need to take all 3 apart and clean? I just bought this engine used. Seemed to be running good before the leak.
Hey man I’ve got the 02 F30TLRA motor. I’ve done my research and it looks like the only differences between the f30 and f40 is the main jet, the needle jet, and the bottom of the bowl, likely a small difference in the plunger but essentially the same thing. The idle jet is the same. For obvious reasons I want to increase power to at least the 40hp should I just replace the main jet to #108 or should I replace the needle jet as well. Would the #108 be too much? Or should I just go for the #95 jet? Please advise. Thanks
That was awesome. Well done. I just purchased an 11' inflatable with a Yamaha 40hp 4 stroke that was shipped from Houston to my slip in Lake Tahoe (6200 elevation). The engine only has 34 hours on it. It will accelerate in neutral to 5000 plus but when in gear I cant get it to go above 2600 RPM and 6 mph. The boat sat for a year and the previous owner put in fule stabilizer. Does this sound like a problem with the jets or fuel filter or pump? Thanks in advance.
Hello.im from finland,i have yamaha f60,2003,also have some problems with engine running,its not so smooth.can you tell me if there are some better size needles to carburetor.i have heard that this is somekind of type problem in these models..
Hello. what is the difference between yamaha f30 and f40 carburetors? just the jet diameter? Or different diffusers? what is the diameter of the diffuser on the f40?
I read it’s a restrictor plate between carb and engine plus a different ECU. If you do it let me know, have the F30 carb version and it’s same weight as F40
Do you still work on these? I see you are in my area based on the sea trial. I have replaced the jets as recommended, and it has cleared up my acceleration issue, it is now flooding the carbs though. Any suggestions or if you still work on motors around here, maybe you can look into this for me?
Hey eric edic. I'm Alex. Can you help me with my problem. After changing main jet in all 3 carbs , my Yamaha don't work correctly. I think very many fuel because my spark plugs - are black. What i need to do.
Hey mate, I just picked up an F40 and it has a leak from the plunger on the top carb. The boot/cap is broken on all 3 carbs but only the top leaks. Is there an internal seal that I should be looking at replacing or just the outer boot? Cheers!
Did you figure out why it was leaking ? Mine is doing the same. Others online are suggesting the needle valves aren't seal off... LMK if you got yours sorted.
hello from greece.i have a question too..can i tune my 4 stroke 2004 yamaha 30 by changing the carburarators of 40?if yes can you help me finding these?or if you can advise something else to increase power?thank you
Jim Nichols you should be able to see through it when held up to a light. the home is tiny but should be able to see through it. sounds like your is blocked. use one of the wires from a wire brush to open it.
Thanks! I have a 30 hp yamaha, that is identical to 40hp. At least , everything that meets the eye is identical. I'm trying to find info about what to change to get those 10 hp difference. Do you know maybe? Jets .. ??
Eric, If you're still monitoring this, I'd love to replace the jets on my 2002 F50 4 stroke with bigger jets. Do you know of any model number that will work? thanks for the great video, really helped me be brave enough to pull my carbs, I also ordered the Carbpro balancer, looks good thanks again, Brett W
eric edic thanks for the video. I followed it exactly . I even bout the same carbtune you use and balanced the carbs really good, I have the same boat and motor. and could only get up to 12mph. i ran it with the cover off to see it the throttle was going all the way up and with the cover off it does 25mph! i put the motor cover back on and 12mph. take it back off 25mph.? then the third time i got it to climb to 25mph with the cover on but you have to move the throttle slow and climb slow I cant do a hole shot it will stay at 12mph at full throttle? it does idle super quiet and low speed moving around is perfect. I do think my rpms are a little high in idle but not bad. any suggestions ? thanks so much
Hi can you make a video of all the wire harness conectors and where they clip on the motor i took my 40 completely apart to replace the power head gasket and valve seal also i used your video to do the jets and clean my carbs my motor is at the machine shop and im worried i might have forgot where evrything goes stupid me i didnt make a video before by the way awsome video man good zooming and detail thanks and best regards with your chanel.
got the same exact motor..had the same exact problem..did your fix and she runs like a charm..many thanks to you young man..
That was life changing for me. I’ve had my fair share of carby issues in the past as we all have . I’ve always been told not to touch them because they are too complicated . But your tutorial made it look and sound easy. Thank you so much.
Yeh. 1st boat 1st outboard 4 me. Very clear, and easy for me thanku I feel accomplished!!
Thanks man. I got same with a aluboat, buster. Watching this, it was pretty easy job. Next time, when proper shop is near, I also put 45 jets. Now only cleaning. I had minimum tools available and no pressurised air. But works now.
Love this, I didn’t change the carbs and my motor ran like a charm after that, I might change the jets one day though. Thanks man this really helped with assembly and re assembly 👍👍
I did this to my 2005 F40. Runs amazing now, but it does drink more fuel with the bigger jets.
I really want to thank you for giveing this advice my 40hp jet drive was really hesitating but i went an got some torch cleaning bits and drilled my jets to the next size of drill bit size its now running like a champ thank you somuch keep doing what your doing your real helpfull!!!!!!!!!!!
This is great.
Thank you very very much, from France. I have the exact same engine (2007) and between 2000 and 3000 it's very difficult to get the power and sometimes the engines is simply stopping.
Your video is perfect, and I will do the same soon.
Best regards.
Philippe
Your channel is amazing brother! Thank you really. It's so helpful and easy to understand.
You should be an instructor. Everything explained very well. Nice job!
Hi ThatBoatGuy, I've the same motor. I must change O-ring and your vidéo is so good !!! Thank for the job ! I'm gonna go out and change the jets!
I've got the exact same problem with a 40hp yammy. Thanks for sharing. I have have to switch out those jets.
Just what I need!
Nice and instructural!
Thank you!
FYI, you can get those O-Rings for 49 cents a piece if you go to a hard ware store that sells them individually. I just bought 10 at the Do-It-Best Hardware store down the street from my house when I rebuilt a set of carbs on my Merc 50hp.
Im purchasing a 06 40 hp yamaha and 100% doing this.
nice i want to get a four stroke engine but i live on a island where we dont have a service center. you should do a video on how to care for the engine like things you should on a regular basis
I'm replacing the accelerator pump belows on my 2000 mercury 40hp 4 stroke. It has the same yamaha powerhead and carbs. How do I remove the accelerator pump rod without breaking anything?
well done...you make it look so easy
Hello, i have the same engine, but the carburator on top will not get fuel... everything is clean and nice video, but i dont know what to do now...
Great video, would you make a video on the choke unit and how to set it up properly that would be great, thanks 🙏👍
great tutorial! will probably do this this weekend. just one question do you need tinker on that brass fuel screw? Mines been idling very rough like it feels like 1 cylinder off onidle but goes fine on wot
I didn’t mark my electric choke wires before I took my carb off. Anyone know how to determine which way to reconnect since they’re all the same color?
Great instructional video.. Good job. Could you tell me the prop size you use on this motor?
Thank you
Bonjour J'ai un problème d'essence qui fuit du pénis .yamaha 4storek Je sais, informe-moi de sa générosité
yes i set them about 2.25 turns out
Where are you located?
@@orlandoveloz2406 St.Petersburg Florida
@@ThatBoatGuy thanks for answer, do you know somebody by Miami ,who’s can fix this issues?
Nice video. Good job
Ciao il mio motore 40 cv 4 tempi tarda l'accensione a freddo poi dopo che parte la prima volta va bene .
By the way you done 9nm mine. Must be 20- 25nm. Will it matter? Mines a 30hp 4strk yamahaha
I am going to attempt to rebuild my carbs 2001 50hp yamaha, F50TLRZ have the exact same problem you had. Carbtuner comes this week and was going to order 4 carb rebuild kits. Seems like there is an upgraded kit from the original. 62Y-W0093-11-00 new kit from old kit 62Y-W0093-10-00 hope it has better jets or something in new kit. Also did you adjust the air mixture screws on carbs?
I have a 1999, F100, Yahama. Idle sneeze and trouble through 2-3k range. Had the carbs cleaned a couple times, nothing fixes it! Any input on a jet change for that?
Hey man I know this is a old video but hoping you had a recommendation for jet upgrade size on the old mercury 4 stroke 90 elpto, it's terrible about clogging constantly. Thanks
Hello! Great video! Can you please indicate what is the name of carburetor instrument that you are using and can it be bought online? Tnx a lot!!
Hi Eric, Is there particular a year or range of years that this occurs?
great videos by the way!
Is this procedure the same for a 50hp
Did you change the Jets on each of the carburetors and can you give me the part number that you changed your 40 horse four stroke with?
Your putting in jets from a small engine? Is that correct?
Also I have a leaking float seal on the top carb, do I need to take all 3 apart and clean? I just bought this engine used. Seemed to be running good before the leak.
Not bad a starter like you.
Hey man I’ve got the 02 F30TLRA motor. I’ve done my research and it looks like the only differences between the f30 and f40 is the main jet, the needle jet, and the bottom of the bowl, likely a small difference in the plunger but essentially the same thing. The idle jet is the same. For obvious reasons I want to increase power to at least the 40hp should I just replace the main jet to #108 or should I replace the needle jet as well. Would the #108 be too much? Or should I just go for the #95 jet? Please advise. Thanks
I’m wondering the same thing for my 30hp as well.
That was awesome. Well done. I just purchased an 11' inflatable with a Yamaha 40hp 4 stroke that was shipped from Houston to my slip in Lake Tahoe (6200 elevation). The engine only has 34 hours on it. It will accelerate in neutral to 5000 plus but when in gear I cant get it to go above 2600 RPM and 6 mph. The boat sat for a year and the previous owner put in fule stabilizer. Does this sound like a problem with the jets or fuel filter or pump? Thanks in advance.
will these jets work on the F40mjha 2002 it has a jet leg on it?
Hello.im from finland,i have yamaha f60,2003,also have some problems with engine running,its not so smooth.can you tell me if there are some better size needles to carburetor.i have heard that this is somekind of type problem in these models..
Is there fuel filter other than the inline filter on the f40
Hello. what is the difference between yamaha f30 and f40 carburetors? just the jet diameter? Or different diffusers? what is the diameter of the diffuser on the f40?
I read it’s a restrictor plate between carb and engine plus a different ECU. If you do it let me know, have the F30 carb version and it’s same weight as F40
I need that carb link. Got any laying around or where i can buy. My local shop dont have any .
Do you still work on these? I see you are in my area based on the sea trial. I have replaced the jets as recommended, and it has cleared up my acceleration issue, it is now flooding the carbs though. Any suggestions or if you still work on motors around here, maybe you can look into this for me?
Hallo, I could kindly contact you for a question about these carburetors? Thank you in advance
Hello from Bulgaria. I have a cuestion. Can i tune up carburators of this yamaha. I have the same engine. Thank You
Why does the carburators have that rubber thing?
Hey eric edic. I'm Alex. Can you help me with my problem. After changing main jet in all 3 carbs , my Yamaha don't work correctly. I think very many fuel because my spark plugs - are black. What i need to do.
Hey mate, I just picked up an F40 and it has a leak from the plunger on the top carb. The boot/cap is broken on all 3 carbs but only the top leaks. Is there an internal seal that I should be looking at replacing or just the outer boot? Cheers!
Did you figure out why it was leaking ? Mine is doing the same. Others online are suggesting the needle valves aren't seal off... LMK if you got yours sorted.
hello from greece.i have a question too..can i tune my 4 stroke 2004 yamaha 30 by changing the carburarators of 40?if yes can you help me finding these?or if you can advise something else to increase power?thank you
Ναι μπορεις το έχω κανει εδώ και 6 χρόνια κοστίζουν 1100€ καινούργια η διαφορά της f30 με f40 ειναι τα καρμπιρατερ
what cleaner do you use? I read you have to be careful what you use or you can take a coating off the carb.
fjmurray25 carb cleaner?
eric edic yes what type of spray or solution did you use? Brp tuner, simple green, ect?
I have a question on the slow speed jet does it have a hole all the way threw it. I think one of mine is pluged.
Jim Nichols you should be able to see through it when held up to a light. the home is tiny but should be able to see through it. sounds like your is blocked. use one of the wires from a wire brush to open it.
This is a great video. I have a 02 F30TLRB and I am constantly fighting this issue. By chance, could you tell me what jets my carburetors would need?
+Tag Out you might just have your jets clogged. I only heard the 40hp yamaha 4 stroke having this problem not the 30hp yamaha
+eric edic 30 hp is the same block I think
Hi! Thanks for the video.. What can you say about fuel consumption, after replacing jets ?
you'll barely see a difference in fuel consumption
Thanks!
I have a 30 hp yamaha, that is identical to 40hp. At least , everything that meets the eye is identical. I'm trying to find info about what to change to get those 10 hp difference. Do you know maybe? Jets .. ??
Have you found out what it takes to make f30 to f40 conversion? Pls email me , tasdimis79@gmail.com
See my reply above
Your reply above?
I don’t see any reply from you. Above, or below.🤷♂️
amazing
Gracias me sirvió de guía 👍
Eric,
If you're still monitoring this, I'd love to replace the jets on my 2002 F50 4 stroke with bigger jets. Do you know of any model number that will work?
thanks for the great video, really helped me be brave enough to pull my carbs,
I also ordered the Carbpro balancer, looks good
thanks again,
Brett W
I am on the same page. Some help please
Me too 🤷
thanks awesome videos I have the same boat and motor. I'm going to try this.
fjmurray25 you must replace the jets. Look in the description box i have the part number
eric edic where can you get that carbtuner? i only see it for sale in the uk? do you have to sync them ?
fjmurray25 will the jets work on a 2004? boats.net say for 2006 and up?
fjmurray25 Yes it will work. Look in my description for the part number for the jets that you need.
eric edic thanks for the video. I followed it exactly . I even bout the same carbtune you use and balanced the carbs really good, I have the same boat and motor. and could only get up to 12mph. i ran it with the cover off to see it the throttle was going all the way up and with the cover off it does 25mph! i put the motor cover back on and 12mph. take it back off 25mph.? then the third time i got it to climb to 25mph with the cover on but you have to move the throttle slow and climb slow I cant do a hole shot it will stay at 12mph at full throttle? it does idle super quiet and low speed moving around is perfect. I do think my rpms are a little high in idle but not bad. any suggestions ? thanks so much
Hi can you make a video of all the wire harness conectors and where they clip on the motor i took my 40 completely apart to replace the power head gasket and valve seal also i used your video to do the jets and clean my carbs my motor is at the machine shop and im worried i might have forgot where evrything goes stupid me i didnt make a video before by the way awsome video man good zooming and detail thanks and best regards with your chanel.
hello but sorry I cannot make a video at the moment because I have sold the boat with the engine and I do not have another motor to show you
how much and where you sell
nuddie1972 what do you mean?
do you sell boats/ engines
Yes
trying clarityto get some
nuddie1972 you can text me at 727-286-0636 if you are looking for a specific motor or boat
They're not 10 mm bolts, they're 6mm bolts with a 10mm head..... people might look up torque for 10mm bolts.... best to use proper verbiage please.
40 hp to what?
Eric can You halp me With advise