Your video was very helpful in the rebuild of my 1993 RMX250 shock. The two bikes share many similarities. Have a blessed day. Happy Thanksgiving from the USA State of Michigan.
Awesome video. Even though it's an older bike it's the same process for any modern shock. Those tools you made are nice! The seal head setting tool is so nice to have when doing a shock.
Love how you zinc plate parts that’s amazing finish and durable, cerakoating is cool,but this is even better esp for fixings great work, learnt some cool things.
Excellent work! Your filming style is very much like Chris at click spring! I'm rebuilding a 95 Honda XL and your attention to detail is making me go back and redo parts I'd skimmed over for a much better finish overall! Thanks!
Simplemente perfecto, una obra de arte, estoy restaurando una Suzuki RMX 250 mod 93, me sirvió muchísimo esto, siempre busqué un tutorial así, tan detallado, muchas gracias por compartir esto, espero con ansias el siguiente video, saludos desde Argentina 👏🏻
Luciano Minoggio que aceite es el que usas para la suspencion tracera el mismo que usa el o hay alguno mejor y en que tipo de viscosidad tengo esa duda
Great video, very helpful on disassembly. I rebuilt a 1989 RMX250 shock, almost identical to what is presented in this video. If the shaft/piston/head assembly is installed in the manner shown - it will result in air within the system, as the seal head has a rather larger cavity on the bottom side that will never allow the air to purge, also the seal head is not correctly positioned and shaft is not fully extended, this causes incorrect oil volume. This "air" will end up within the compression adjuster when the shock is installed into bike. The bleed screw located between the reservoir and main body needs to be utilized. Add oil into main reservoir and allow the oil to flow into reservoir slightly. Install the shaft assembly and stoke as shown in video, strike shaft eyelet with a plastic hammer to further remove air from valve stack, these steps will also clear air from compression adjuster, a torch can be used to flash air bubbles away. Hold a hand over reservoir to inhibit oil from further equalizing into reservoir , install seal head and clip, then pull/seat shaft assembly against clip (full extended). Add/remove oil as needed from reservoir and install bladder just until it seats the seal, then reorient shock body in vise so bleeder screw is pointed straight up. Remove screw and into the bleed port, install a small section of hose, appropriately sized funnel or syringe that will hold roughly 20cc of oil. The bladder and clip can now be fully installed and bladder can be pulled back against clip. Here is where the final air bleeding takes place. Make sure there is adequate oil in the bleed port oil holding device. Stroke the shaft in and out until you are certain all air has been bled from shaft assembly, finally shaft needs to fully extended out, remove oil holding device and reinstall bleed screw. I used 5wt oil and charged to the indicated 145psi nitrogen. After riding and comparing to original pre-rebuild ride quality, I feel 7wt oil and 200si is more appropriate . I lack the official specifications, so just my 2cents.
Where did you source parts for this shock? I have a 1992 RMX250 and i am having are ridiculously hard time finding a rebuild kit for my shock. Great video!
@@GoldsGarage i did eventually have success but i had to find each individual part from different brands and companys. If i can remember it was a combination of moose racing, all balls racing, and maybee something else. It was a while back.
Hola te escribo desde Argentina , excelente video . Tengo una xr 250 r del 91 q tiene un monoshock creo idéntico. Lo desarme siguiendo tus pasos , cambien el pulmón q estaba pinchado y lo rearme como hiciste vos. El problema q cuando lo arme me pierde aceite por los dos agujeritos de tapa q lo cierra . Eso no debería pasar . Te consulto deben estar fallando el o ring y el retén del émbolo móvil? Desde ya gracias y espero ansioso tu respuesta y opinión
Did you buy a new shrader valve for the piece that you use to fill the shock with nitrogen ? I think mine leaks and I don’t know if I can replace the valve itself cause when I went to fill it it leaked somewhere around the shrader valve and it’s sort of messed up from someone cross threading the old cap on it
Hi. Really enjoying yr videos. Could you please tell me the paint you used for the shock spring as i need to do mine and i like the results you have achieved with yours. thanks.
I'm looking to rebuild my shock soon and I have an rmx250 which is very similar to this bike especially in terms of suspension. I am wondering if there is any better ways of refilling the oil? and what did you use to clean the internals of the shock? can I use brake cleaner?
amazing,can you give some info about the zinc plating?What solution are you using?Don't you buff the parts when you take them out from the solution?They come so shinny straight away?
I am almost done with a build very similar to yours! I am at the final stages and have had no luck... Do you happen to remember which shock bladder you are using? I have searched high and low and have had no success... PLEASE HELP!!
Do you know any method of purging the shock absorber without having to use a vacuum device, it would be of great help, I await your clarification, greetings.
Hi. I liked your video. I need to service a rear shock on a 2003 yamaha r1. I want to know what reference and amount of oil should I add, I also want to know what air pressure the preload should carry. I hope you can help me. From Colombia Thank you very much! Hola. me gusto su vídeo. Debo hacer mantenimiento de un amortiguador trasero de una yamaha r1 2003. Deseo saber que referencia y cantidad de aceite debo agregar, también deseo saber que presión de aire debe llevar la precarga. Espero pueda ayudarme. Desde Colombia ¡Muchas Gracias!
Hi like everyone else I am hooked and can't wait to see end result, and I owe you a big thank you for video on front suspension as it help me rebuild my 1993 rm 250. Would you know the stock gearing on the chain and sprockets my had 13 front and 50 rear many thanks, big fan in the UK 👍
Hi how are you? I followed your advice to repair my 250 cr Monoshock. I couldn't get the nitrogen charge. So I inflated it with air. He walked well for a while and suddenly stopped walking. It looked like it had the spring alone. The next day he was back to normal. Could it be due to bad assembly and there is air left? Or is it the air in the bladder that causes this?
No idea if this is still being followed but worth a try. Wondered what year CRF bump stop did you use? We are just rebuilding a 92 RM and this part is no longer available. The one you use fits perfectly. Any help much appreciated.
How's it going? I had a question, I am restoring a 1990 Suzuki RM 250 and can't find anywhere to buy a front wheel spacer. My bike is missing that. Any recommendations, I would really appreciate the help. Thanks
Where did you get spare parts for the shock like new seals? I have the same work to do on my 1994 Öhlins shock but can't find any replacement parts for this model, it seems it is too old.
Cant get over the detail you are putting into every little thing on this restoration..Well Done !!!
Somebody says perfection doesn’t exist, but @g9 garage is an exception
Your video was very helpful in the rebuild of my 1993 RMX250 shock. The two bikes share many similarities. Have a blessed day. Happy Thanksgiving from the USA State of Michigan.
Awesome video. Even though it's an older bike it's the same process for any modern shock. Those tools you made are nice! The seal head setting tool is so nice to have when doing a shock.
I looked on RUclips as I do most days and was happy to see a new upload of the build , yet again a joy to watch 👏🏻
Your videos are so relaxing and informative... please keep going with this build!
Love how you zinc plate parts that’s amazing finish and durable, cerakoating is cool,but this is even better esp for fixings great work, learnt some cool things.
I rebuilt the rear shock on my rmx250 watching this video thanks!
Absolutely beautiful work sir
Excellent work! Your filming style is very much like Chris at click spring! I'm rebuilding a 95 Honda XL and your attention to detail is making me go back and redo parts I'd skimmed over for a much better finish overall! Thanks!
Thanks mate! Clickspring is one of my favourite channels! Obviously influenced my vids too...
Good luck with your XL build mate!
I’m keen to see it fully built!!
This is insane! Your attention to detail is next level. Well done!
Man, very meticulous and professional job!
awesome! I can't wait to see the bike done and running.
Simplemente perfecto, una obra de arte, estoy restaurando una Suzuki RMX 250 mod 93, me sirvió muchísimo esto, siempre busqué un tutorial así, tan detallado, muchas gracias por compartir esto, espero con ansias el siguiente video, saludos desde Argentina 👏🏻
Luciano Minoggio que aceite es el que usas para la suspencion tracera el mismo que usa el o hay alguno mejor y en que tipo de viscosidad tengo esa duda
Enjoyed watching, and your attention to detail I found familiar. Cheers. PS, I also live local, go figure.
Great video, i'm looking forward to do this myself on my XR.
Handy tools you made, expecially the "bullettool " for this job.
Great video, very helpful on disassembly. I rebuilt a 1989 RMX250 shock, almost identical to what is presented in this video. If the shaft/piston/head assembly is installed in the manner shown - it will result in air within the system, as the seal head has a rather larger cavity on the bottom side that will never allow the air to purge, also the seal head is not correctly positioned and shaft is not fully extended, this causes incorrect oil volume. This "air" will end up within the compression adjuster when the shock is installed into bike.
The bleed screw located between the reservoir and main body needs to be utilized. Add oil into main reservoir and allow the oil to flow into reservoir slightly. Install the shaft assembly and stoke as shown in video, strike shaft eyelet with a plastic hammer to further remove air from valve stack, these steps will also clear air from compression adjuster, a torch can be used to flash air bubbles away. Hold a hand over reservoir to inhibit oil from further equalizing into reservoir , install seal head and clip, then pull/seat shaft assembly against clip (full extended). Add/remove oil as needed from reservoir and install bladder just until it seats the seal, then reorient shock body in vise so bleeder screw is pointed straight up. Remove screw and into the bleed port, install a small section of hose, appropriately sized funnel or syringe that will hold roughly 20cc of oil. The bladder and clip can now be fully installed and bladder can be pulled back against clip. Here is where the final air bleeding takes place. Make sure there is adequate oil in the bleed port oil holding device. Stroke the shaft in and out until you are certain all air has been bled from shaft assembly, finally shaft needs to fully extended out, remove oil holding device and reinstall bleed screw. I used 5wt oil and charged to the indicated 145psi nitrogen. After riding and comparing to original pre-rebuild ride quality, I feel 7wt oil and 200si is more appropriate . I lack the official specifications, so just my 2cents.
Very nice to see your video. Keep it up bro.
That lathe is more useful than I would have expected.
Awesome video once again!
Damm this bike is going to look great once it has been fully restored.
best videos on youtube by far!
Beautiful work!!!
Woooo that looks great keep up the great work
Well i'm off to the bank manager, i'll let you know how i get on! Great video by the way...
More awesome work! Looking forward to the next video :o)
Gracias excelente video...🇨🇱🇨🇱☘️☘️
Complimenti.
Thanks
Where did you source parts for this shock? I have a 1992 RMX250 and i am having are ridiculously hard time finding a rebuild kit for my shock. Great video!
Did you have any success? I am dying trying to find a shock bladder...
@@GoldsGarage i did eventually have success but i had to find each individual part from different brands and companys. If i can remember it was a combination of moose racing, all balls racing, and maybee something else. It was a while back.
good job bro, i like this 👍
Wow veramente complimenti super professional..!!
So satisfying
Adorei, trabalho fantástico!
Great Job as always!!!
(I haven't done watching the video btw)
Great job how many hours were spent restoring
Hola te escribo desde Argentina , excelente video . Tengo una xr 250 r del 91 q tiene un monoshock creo idéntico. Lo desarme siguiendo tus pasos , cambien el pulmón q estaba pinchado y lo rearme como hiciste vos. El problema q cuando lo arme me pierde aceite por los dos agujeritos de tapa q lo cierra . Eso no debería pasar . Te consulto deben estar fallando el o ring y el retén del émbolo móvil? Desde ya gracias y espero ansioso tu respuesta y opinión
Muchas gracias...es Perfecto
Здорово смотреть на работу человека с прямыми руками. Да и когда запчасти нужные есть. У нас в Улан-Удэ нихрина нет...
Very very very nice videos👌
Looking fresh!!
Did you buy a new shrader valve for the piece that you use to fill the shock with nitrogen ? I think mine leaks and I don’t know if I can replace the valve itself cause when I went to fill it it leaked somewhere around the shrader valve and it’s sort of messed up from someone cross threading the old cap on it
Amazing!
Hi. Really enjoying yr videos. Could you please tell me the paint you used for the shock spring as i need to do mine and i like the results you have achieved with yours. thanks.
I'm looking to rebuild my shock soon and I have an rmx250 which is very similar to this bike especially in terms of suspension. I am wondering if there is any better ways of refilling the oil? and what did you use to clean the internals of the shock? can I use brake cleaner?
THIS IS CLEAAN.
Hi,nice vid. I followed all the steps but my problem is the bladder. I can't find any replacement. What can i buy for replacement. Thank you
Did you happen to find one? This is the LAST piece to a full restoration and its quite frustrating...
amazing,can you give some info about the zinc plating?What solution are you using?Don't you buff the parts when you take them out from the solution?They come so shinny straight away?
Wanted to see how you did the yellow coat. Only reason I watched this 🤣
I am almost done with a build very similar to yours! I am at the final stages and have had no luck... Do you happen to remember which shock bladder you are using? I have searched high and low and have had no success... PLEASE HELP!!
What kind of oil do you use to change monoshok? Thank you
What are the dimensions of the shock bullet I have the same shock thanks great videos.
Do you know any method of purging the shock absorber without having to use a vacuum device, it would be of great help, I await your clarification, greetings.
What are you using for yellow paint? I’m doing a 93 rm125 and want to use the same color
I wonder how many rides you will do before the rebound damping quits working.
Hi. I liked your video. I need to service a rear shock on a 2003 yamaha r1. I want to know what reference and amount of oil should I add, I also want to know what air pressure the preload should carry. I hope you can help me. From Colombia Thank you very much!
Hola. me gusto su vídeo. Debo hacer mantenimiento de un amortiguador trasero de una yamaha r1 2003. Deseo saber que referencia y cantidad de aceite debo agregar, también deseo saber que presión de aire debe llevar la precarga. Espero pueda ayudarme. Desde Colombia ¡Muchas Gracias!
Mate did you have two left over circlips upon reassembly ?? Where did they go?
trabalho perfeito.parabens...
Great video 👍👍 .but I have some questions . What is that process called at @8:00 - @8:30 and what it for ? Thx.
Zinc plating. Check out the episode on zinc plating!
Hi like everyone else I am hooked and can't wait to see end result, and I owe you a big thank you for video on front suspension as it help me rebuild my 1993 rm 250. Would you know the stock gearing on the chain and sprockets my had 13 front and 50 rear many thanks, big fan in the UK 👍
13/49 120 link
Hello friend, could you give me the reference of the oil you use?
Can you give the details of the zinc plating...?
Thanks.
Hi how are you? I followed your advice to repair my 250 cr Monoshock. I couldn't get the nitrogen charge. So I inflated it with air. He walked well for a while and suddenly stopped walking. It looked like it had the spring alone. The next day he was back to normal. Could it be due to bad assembly and there is air left? Or is it the air in the bladder that causes this?
How do you plan to set preload? Trying to figure out the best way on my 93. With the spring going against the retainers it’s tough
Can i use fork oil for this shock?
I'm having trouble pulling the shaft out. It seems like the seal is getting caught and I took the circlip out. Any help
No idea if this is still being followed but worth a try. Wondered what year CRF bump stop did you use? We are just rebuilding a 92 RM and this part is no longer available. The one you use fits perfectly. Any help much appreciated.
What was the valve torque setting too......? Thanks
From memory the bump stop was from a 2010
@@G9Garage Thank you for the help.
How's it going? I had a question, I am restoring a 1990 Suzuki RM 250 and can't find anywhere to buy a front wheel spacer. My bike is missing that.
Any recommendations, I would really appreciate the help.
Thanks
Any local machine sho can make it
If you're not sure about measuring up take the bike to them and they will be able to work it out
Could I ask if the frame of the bike and also the shock spring have been powder coated or painted? Thanks
Hi, the frame and spring are both painted.
Well constructed video!!
Are the rm 125 and 250 practically the same parts and assembly? Because I’m doing what you are on my rm 125
Cheers Callum. The 125 and 250 have plenty in common. The basic principles of restoration and assembly are the same.
G9Garage thanks for that! I’ll keep watching the vids as long as you make them!
Where did you get spare parts for the shock like new seals? I have the same work to do on my 1994 Öhlins shock but can't find any replacement parts for this model, it seems it is too old.
From memory the shock seal was still available from Suzuki
Cool song
Can you do a diy on your zinc set up !!!
MegaPro!!!
link new, can't believe it !
Come si chiama il processo all interno del contenitore?
Расстояние sic когда выставлять собрался?😉
VC TEM QUE MOSTRA A DESMOTAGEM E A MONTAGEM
Debería darlo en español muy bueno
Tengo una suspensión elka defectuosa esos sellos lo venden para arreglarla oh cómo puedo hacerlo.
Hi, donde puedo conseguir el kit para reparar
Me encanta tu trabajo, exitos
one hundredth like
Hola que dencida de aceite le pone s
please rebuild honda xr 250 md30
Great video, are you Clickspring!? Haha
ADSlammer haha I wish I had his talent!
Cuanto vale ese martiguador
Upload more :)))))
New video this weekend!
exelente calidad de servicio