Do you know how to Bind the helicopter?Right out of the box.If it don't work mine don't work.I don't know what's wrong with it.Post to take it out of the box.Put batteries in and fly mine don't
cant help you other then if your on 27 or 49 mhz it just does it , if your on 2.4 or 5ghz it should just work turn on the heli first then the radio if that fails do the reverse if that still fails contact the company or read your instruction manual no all of these are the same
lol ok so I made a typo . the point is radio or remote same thing really, unless you want to be really picky cause back in the day remote was a wired unit to the item ..
Hi, i bought a brand new helicopter but it won't respond to my transmitter. I tried to link it but nothing happened. The transmitter has brand new batteries and the helicopter is fully charged. What happened?
Hey kevin nice video I will check my remote tonight I have a yiboo uj300 and its a very good helicopter took a couple crashes as a newbie but only broke landing skids. My problem is I turn helicopter on the pcb light flashes then I turn the remote on and the flashing stops which I guess represents binding of tx and rx solid light. When I deliver throttle over half power it shuts off and the light starts flashing. Is this a pcb issue or transmitter problem. Thank you
interesting , try turning on the radio first then the heli then push the throttle all up then down then see what happens , but it could be the PCB or the radio hard to tell with out a spare radio to confirm the radio being a problem
The same happens with my Lama M01 27 Mhz, the heli stops flashing showing it is bound and then when the throttle gets up it starts flashing, and the heli does not react to commands. The only command it react to is the switching on/off the diode on the heli.
KevinMillard68 I also did as you advised. First switched on the TX and then the RX, before puttuing throttle up, the heli light flashes- no binding, then throttle gets up, the flashing stops - binding OK, after returning throtlle down, the heli begins to flash - Error, binding problem. During all this, the heli does not perform commands (no rotation).....So what is up with the heli? Is this RX or TX?
Sergii Lobko could be either one id start tho with the RX in the heli first .. not to often a tx goes bad but make sure you got full y charged battery in the heli and good batterys in the tx even if the power comes on on the radio this does not mean the batterys are good anymore so make sure try a fresh set then try again if that fails get a new RX first
Please reply, the problem with my RC remote is that the throttle lever is half raised, the power LED is flashing (I replaced the LED that came with the remote because it was rusty and broken) and the connection to the RC is lost, which part should be checked, the remote board is almost the same as the one you have , Thank You rc helicopter type s033g
you always start witht he throttle at 0 the raises it to fire up the heli, if its blinking it could be your throttle stick is not at 0 so all the way down / or you could have bad batterys in the radio , or something is wrong with either your radio or the reciever in whch case replace with new parts if you can still get them
I have tried replacing the battery using a 6 volt adapter, the problem has been resolved, now the problem has changed to the helicopter PCB. The mosfet in the receiver is broken, thank you for the advice. Sorry, my English is bad
Hi I have a 3 channel remote and it just stop turning on, I've tried changing the batteries but it won't turn on. Do you know how to repair it or how to know which remote to buy?
my remote controlled h2062 has a transmitter but it is not working Is that a battery? antenna ? +Kevys Rc & Music, i need your help so that i can fly my RC helicopter tomorrow.
Wow! I have the very same remote control unit that you have. My on/off switch is giving problems. Loose contact. Need to keep my thumb over it to hold it at on position. Moreover now my helicopter is not gaining altitude. It rises only one foot. Had used it well only around ten times. Any idea why it is not gaining altitude?
run the battery till it dies and recharge do this 3 times then try again lipos do hold a memory no matter what the science says i have prved this to be true many times that they hold a memory
Thank you so much for the advice. Will try that. But the same thing happened when I had tried with new batteries in the helicopter, and also in the remote.
well then your problem is likey the motors are shot in the heli if its not getting proper height and replacing the power switch i the radio might be a good idea but that wont affect the height in which it can fly
Yeah, replacing the motor might be wise. Another friend had suggested that the flywheel might be loose owing to a crack. I don't think I'll get a replacement for the flywheel, but may be able to get a new motor. The make is Hamleys (imported from England).
I have an rc helicopter I am trying to fix.... i have an electronics background but not a lot of experience with these little toys. I have a chopper that says it is a 27 MHz board and the remote says 27 MHz but it will not talk. Both batts and pwr supply is good but it still wont talk. Is there an adjustment for the freq?
there is an adjustment for the frequency and iam uploading a video shortly , did this problem just all the sudden happen cause if it did its more likely a bad solder joint on the helicopter PCB board or the PCB board toasted. could also be a broken wire
Hello and thank you for any help you may have. I have a TX juice AI Copter and the remote will not turn on. I have tried different batteries, different orientations/polarities and tried turning it on close to the helicopter. The helicopter is fully charged and when I flip the switch on it it turns on. But when I flip the switch on the remote it does not do anything.
+Kevys Rc & Music solder back a broken wire or solder on a new switch if its broken if its not the switch or a broken wire then you put it in the junk and buy a new radio if you can get one for it if not pitch the whole thing and buy a new machine
RX would be the receiver that goes in the helicopter. TX is the transmitter that sends the signal to the receiver. Remote control for the television, etc.
nope you cant it is what it is .. get your self a wltoys v911 heli from banggood.com there awesome and 4 channel as well realy durable 2.4 ghz long range indoor and outdoor as we
Howdy! I am having problems with my remote. (I know it is the remote because of various tests I have done). The problem I am having is that the left "joystick" only works for the throttle (up and down) on my quad-copter. the left and right doesn't do anything. (I have it set to control the yaw of my quad copter but nothing happens. I can switch it around so that it controls the left-right movement but again it doesn't work and that is how I know it is the control). When I switch the controls around the right side works both ways. but here is my problem. the controls are stuck right on the motherboard of the control. so I don't have any wires to check. I am attaching a link to a few pics so you can see what I mean. On the other side of the board you can see that one post is slightly less soldered then the others. is this perhaps the problem? the solder "dot" i am talking about is circled in red in both pictures. if you compare it to the others around it you can see that it isn't as well done. drive.google.com/folderview?id=0B_uE9ZYoAa0Zd3ltb1FqN2ZnclU&usp=sharing thoughts? thanks
recheck and make sure the batteries are in correctly other wise no i cant help you anything can go wrong and its not infront of me so i have no idea could be the power switch could be a wire let go its impossible to tell you ,, take it apart and see for you self if get a test meter as well and check for continunuty on the switch and other test points as well id start there
can u plssss help me i have flysky fs i6 and recently i overvolted my transmitter with twice required it worked few times and then one time the brightness was increased and stopped working.Now not turning ON on newly changed battery. plss help me i don't have enough money to buy new one
I have a syma so33g it looses connection just as soon as you move the remote from the helicopter all batteries are new and the helicopter battery is fully charged what do I do
with out the unit in front of me i can not tell you whats wrong with it so it makes it impossible for me to trouble shoot this auctual problem it could be the radio has a problem or the main board in the heli has a broken solder joint when is comman on the antena wire or perhaps a circut has a bad connection point so look everything over there and see if you can see any problems there broken connection points can be resolderd and if nothing shortedout and blew then a simple resoloder job should fix it
id love to but all i have of my own helis right now are al 3 channel helis so they use and all in one board in them so i dont think that will help you out much at all sorry
hi i'm noel i have a vulture rc helicopter 40mhz once i was flying it and crashed at a height of about 25 feet whn i turned it on again it will no longer spin
charms robles try rebinding but recharge your battery first and make sure the batterys in your radio are also still good and strong try that and let me know what happens
dont know what to tell you ,, try a new set of batteries in the radio ,, also check you heli battery maybe its at the end of its charge cycles and its the problem ,, so many things could be wrong , and its not infront of me so i dont know what else to tell you ..
i also have the same problem friend. When i connect battery to helicopter i sound beep beep beep.... non-stop and have blue & red light at the same time. any advise dear friend
could be slipping pinion gear on the motor or bad battery,these lipos will can hold a memory tho i know they say they dont i have seen this many times,, so what you do is run the blades slow till the heli just stops your leds will still flash then charge it up and repeat 3 times making sure each time to run it down till the blades stop.. also make sure to allow the battery to cool for 5 full mins before each recharge which you should always do any how if this fixes it then cool. if not then replace with new battery and that should fix it .if its not working still then also make sure no hair or anything is jamming stuff up if its clear then next is the motors need to be replaced
Hello Congrats on the video! It really helped me find out if the issue was the helicopter or the receiver. Once I realized that the helicopter showed "no signal" from the receiver I opened it and.. I have a few toasted transistor, but only on the "LED light box" I am not sure what about to do next! Would you please take a look at this and tell me if it is repairable? s25.postimg.org/ln734ehpb/IMG_20140525_134908.jpg
i know that heli its indoor only and its infared control so very limited range it is what it is and you have to kee the radio pointed at it also keep away from bright lights and dont be pressing the remote for your tv when flying as that knocks them out of the air
what is my control take a while to connect to the helicopter.......some times the helicopter just move on its own even if the control is off. what could be the problem?
thank you for putting out this video, for people who just want to help their child
Do you know how to Bind the helicopter?Right out of the box.If it don't work mine don't work.I don't know what's wrong with it.Post to take it out of the box.Put batteries in and fly mine don't
cant help you other then if your on 27 or 49 mhz it just does it , if your on 2.4 or 5ghz it should just work turn on the heli first then the radio if that fails do the reverse if that still fails contact the company or read your instruction manual no all of these are the same
lol ok so I made a typo . the point is radio or remote same thing really, unless you want to be really picky cause back in the day remote was a wired unit to the item ..
Hi, i bought a brand new helicopter but it won't respond to my transmitter. I tried to link it but nothing happened. The transmitter has brand new batteries and the helicopter is fully charged. What happened?
Same here
Hey kevin nice video I will check my remote tonight I have a yiboo uj300 and its a very good helicopter took a couple crashes as a newbie but only broke landing skids. My problem is I turn helicopter on the pcb light flashes then I turn the remote on and the flashing stops which I guess represents binding of tx and rx solid light. When I deliver throttle over half power it shuts off and the light starts flashing. Is this a pcb issue or transmitter problem. Thank you
interesting , try turning on the radio first then the heli then push the throttle all up then down then see what happens , but it could be the PCB or the radio hard to tell with out a spare radio to confirm the radio being a problem
The same happens with my Lama M01 27 Mhz, the heli stops flashing showing it is bound and then when the throttle gets up it starts flashing, and the heli does not react to commands. The only command it react to is the switching on/off the diode on the heli.
KevinMillard68 I also did as you advised. First switched on the TX and then the RX, before puttuing throttle up, the heli light flashes- no binding, then throttle gets up, the flashing stops - binding OK, after returning throtlle down, the heli begins to flash - Error, binding problem. During all this, the heli does not perform commands (no rotation).....So what is up with the heli? Is this RX or TX?
Sergii Lobko could be either one id start tho with the RX in the heli first .. not to often a tx goes bad but make sure you got full y charged battery in the heli and good batterys in the tx even if the power comes on on the radio this does not mean the batterys are good anymore so make sure try a fresh set then try again if that fails get a new RX first
Please reply, the problem with my RC remote is that the throttle lever is half raised, the power LED is flashing (I replaced the LED that came with the remote because it was rusty and broken) and the connection to the RC is lost, which part should be checked, the remote board is almost the same as the one you have , Thank You rc helicopter type s033g
you always start witht he throttle at 0 the raises it to fire up the heli, if its blinking it could be your throttle stick is not at 0 so all the way down / or you could have bad batterys in the radio , or something is wrong with either your radio or the reciever in whch case replace with new parts if you can still get them
I have tried replacing the battery using a 6 volt adapter, the problem has been resolved, now the problem has changed to the helicopter PCB. The mosfet in the receiver is broken, thank you for the advice. Sorry, my English is bad
Hi I have a 3 channel remote and it just stop turning on, I've tried changing the batteries but it won't turn on. Do you know how to repair it or how to know which remote to buy?
first off what make and model is the heli that would help alot. to know , some of these things you cant get parts for but alot you can
I'm not sure about the model the helicopter just says flyer model and it's a replica of a apache, thanks for replying.
John Velazquez shoot me video with close ups and ill see what i can find out for you , send me the link to the video once you have it uploaded
Ok, thanks for the gelp
John Velazquez your welcome
my remote controlled h2062 has a transmitter but it is not working
Is that a battery? antenna ?
+Kevys Rc & Music, i need your help so that i can fly my RC helicopter tomorrow.
Wow! I have the very same remote control unit that you have. My on/off switch is giving problems. Loose contact. Need to keep my thumb over it to hold it at on position. Moreover now my helicopter is not gaining altitude. It rises only one foot. Had used it well only around ten times. Any idea why it is not gaining altitude?
run the battery till it dies and recharge do this 3 times then try again lipos do hold a memory no matter what the science says i have prved this to be true many times that they hold a memory
Thank you so much for the advice. Will try that. But the same thing happened when I had tried with new batteries in the helicopter, and also in the remote.
well then your problem is likey the motors are shot in the heli if its not getting proper height and replacing the power switch i the radio might be a good idea but that wont affect the height in which it can fly
Yeah, replacing the motor might be wise. Another friend had suggested that the flywheel might be loose owing to a crack. I don't think I'll get a replacement for the flywheel, but may be able to get a new motor. The make is Hamleys (imported from England).
well do let me know how you make out with it
Hi. Good video! Helicopter " Remote Control" is actually a Transmitter.
I have an rc helicopter I am trying to fix.... i have an electronics background but not a lot of experience with these little toys. I have a chopper that says it is a 27 MHz board and the remote says 27 MHz but it will not talk. Both batts and pwr supply is good but it still wont talk. Is there an adjustment for the freq?
sometimes you can adjust them but usualy you dont what heli do you have thats giving you the problem
there is an adjustment for the frequency and iam uploading a video shortly , did this problem just all the sudden happen cause if it did its more likely a bad solder joint on the helicopter PCB board or the PCB board toasted. could also be a broken wire
Hello and thank you for any help you may have. I have a TX juice AI Copter and the remote will not turn on. I have tried different batteries, different orientations/polarities and tried turning it on close to the helicopter. The helicopter is fully charged and when I flip the switch on it it turns on. But when I flip the switch on the remote it does not do anything.
+AJXD Gaming 3 things a broken wire in the radio or a bad switch or its toast
+Kevys Rc & Music ok so how would I fix those things?
+Kevys Rc & Music solder back a broken wire or solder on a new switch if its broken if its not the switch or a broken wire then you put it in the junk and buy a new radio if you can get one for it if not pitch the whole thing and buy a new machine
thanks and yes I know but a lot of people refer to them as remote control or RX or radio etc.
RX would be the receiver that goes in the helicopter. TX is the transmitter that sends the signal to the receiver. Remote control for the television, etc.
hey bro i have lost antena of my helicopter remote so can i use any other antena or use something else except antena like wire
well yes you can use another antenna as long as it will fit and work on the same frequency then your fine
really thanx for ur reply one more question bro my copter wont fly how i can fix it
your welcome
did can be upgrade ?
nope you cant it is what it is .. get your self a wltoys v911 heli from banggood.com there awesome and 4 channel as well realy durable 2.4 ghz long range indoor and outdoor as we
Howdy!
I am having problems with my remote. (I know it is the remote because of various tests I have done). The problem I am having is that the left "joystick" only works for the throttle (up and down) on my quad-copter. the left and right doesn't do anything. (I have it set to control the yaw of my quad copter but nothing happens. I can switch it around so that it controls the left-right movement but again it doesn't work and that is how I know it is the control).
When I switch the controls around the right side works both ways. but here is my problem. the controls are stuck right on the motherboard of the control. so I don't have any wires to check. I am attaching a link to a few pics so you can see what I mean.
On the other side of the board you can see that one post is slightly less soldered then the others. is this perhaps the problem? the solder "dot" i am talking about is circled in red in both pictures. if you compare it to the others around it you can see that it isn't as well done. drive.google.com/folderview?id=0B_uE9ZYoAa0Zd3ltb1FqN2ZnclU&usp=sharing
thoughts? thanks
+Lord Queezle resolder any bad contacts you find and then try again and see what happens
can u help me i have 3 channel remote and it just stop turning on i've tried changing the batteries but it won't turn on TY
recheck and make sure the batteries are in correctly other wise no i cant help you anything can go wrong and its not infront of me so i have no idea could be the power switch could be a wire let go its impossible to tell you ,, take it apart and see for you self if get a test meter as well and check for continunuty on the switch and other test points as well id start there
i have a xdrone hd and my controller dropped. and it wont turn on. how do i fix it?
take it apart find out what broke and fquire out a way to repair it thats what i do
mine keeps on beeping constantly I don't know what's wrong with it can you try to tell me about that
no idea man
i have 2ch remote control helicopter and it doesn't move side and it doesn't come in my control what should I do??? can you tell me plz
2 channle is not supposed to move side to side , buy a 3 or 4 channel heli
Sir my remote is of another kind . And its left right back and front button is not working . Can you tell me how can I fix it.
try resoldering the connections of that fails good for the parts and reaplace the parts or order a new radio
Thanks
My power is broken
can u plssss help me i have flysky fs i6 and recently i overvolted my transmitter with twice required it worked few times and then one time the brightness was increased and stopped working.Now not turning ON on newly changed battery. plss help me i don't have enough money to buy new one
well there is no help other then a new one sorry
I have a syma so33g it looses connection just as soon as you move the remote from the helicopter all batteries are new and the helicopter battery is fully charged what do I do
with out the unit in front of me i can not tell you whats wrong with it so it makes it impossible for me to trouble shoot this auctual problem it could be the radio has a problem or the main board in the heli has a broken solder joint when is comman on the antena wire or perhaps a circut has a bad connection point so look everything over there and see if you can see any problems there broken connection points can be resolderd and if nothing shortedout and blew then a simple resoloder job should fix it
Thank You ! That was very informative!
Troy Smith ghanshyam
your welcome
My rc helicopter can not lift up,only lift up /fly 10 cm from the ground,what happen?
wayangede2007 i have no idea what happen to your heli but it could be your battery is weak try a brand new fully charge battery.
Ok thank you
wayangede2007 your welcome
Can you just tell me the pcb board name......of remote on 40 mhz
cant help you on that i also dont complety understand what your asking
brother i just want to understand how the signal is mounted over the wave that is generated by remote controller means transmitter
by the way thanks a lot.
@@manishjadonrajput3095 if you want to know that then you need to google that info i dont have the time to answer that even in laymans terms
bro my 3.7v helicopter not run 3.7v his run 6v how to fix plz replay
if your heli uses 3.7 then you use 3.7 if its a 6 volt then you use 6 volt thats how things work
Please tell me how to repair QC 06 helicopter system
might help to tell me what the problem is first other wise i cant help
my system is not working so post the video to repair the helicopter system
i cant unless i know what the problem is sorry your on your own on this one
hy bro my flip key is not working in my drone remote plz help me
take the radio apart fnd out what broke thats all i can tell you
hope the slap back/feedback (on the negative side) doesn't discourage you!
sir my rc heicopter's remote controller light up red and turn off (like morse code) and it's not working at all!!!!
+Mohammed Essam have you intstalled new batteries ,, also alot of remotes you have to put full throttle up then down to bind them to the helicopter
+Kevys Rc & Music yes i have installed new battery but...it must 1.5 ????
+Kevys Rc & Music but thanks for your" fast answering service " ; )
+Mohammed Essam you have to use the battertys the radio requires yes .. well if the new batteires dont fix your problem then you ll need a new radio
+Mohammed Essam your welcome
id love to but all i have of my own helis right now are al 3 channel helis so they use and all in one board in them so i dont think that will help you out much at all sorry
hi i'm noel i have a vulture rc helicopter 40mhz once i was flying it and crashed at a height of about 25 feet whn i turned it on again it will no longer spin
you could have broken off a battery wire inside the heli
but my tail light still functions when i turn on the heli switch
KevinMillard68 but my tail light still functions when i turn on the heli switch
charms robles try rebinding but recharge your battery first and make sure the batterys in your radio are also still good and strong try that and let me know what happens
I have a rc helicopter and it turn on but it doesn't work with the controller.Whats wrong?
your welcome
Yeah, I’m looking for tips and tricks and how to rebuild the helicopter controller
this is the only video i have on the subject
My remote control is showing only red light and not showing green light. Can you say what's the problem???? Plz
i cant tell you when its not infront of me all are different this is a basic repair video ,, but try new batteries to start with and charge the heli
Hi how to fix abatery of rc helicopter
what seems to be the problem with the battery be more specific
Mara helicopter kay back motor not work please help me
best to give me a better explantion have no idea what your trying to say
More like your being to critical for no reason at all
sir my helicopter remote is no working
dont know what to tell you ,, try a new set of batteries in the radio ,, also check you heli battery maybe its at the end of its charge cycles and its the problem ,, so many things could be wrong , and its not infront of me so i dont know what else to tell you ..
my copter rc is 3 channel and it is not showing anything
be more specific please to the problem otherwise i cant help
My remote is for a swift s2 infrared hello
its still me noel in addition the pcb light does nit light on
what is the __-ch of helicopter?
the radio in the video is a 3 channel
★★★★★
Great video!
Okthank you
thanks I do try
I have no clue what your talking about
my helicopter is not flying only moving round
+Sapana Chaudhari could be the battery could be anything
i also have the same problem friend. When i connect battery to helicopter i sound beep beep beep.... non-stop and have blue & red light at the same time. any advise dear friend
could be slipping pinion gear on the motor or bad battery,these lipos will can hold a memory tho i know they say they dont i have seen this many times,, so what you do is run the blades slow till the heli just stops your leds will still flash then charge it up and repeat 3 times making sure each time to run it down till the blades stop.. also make sure to allow the battery to cool for 5 full mins before each recharge which you should always do any how if this fixes it then cool. if not then replace with new battery and that should fix it .if its not working still then also make sure no hair or anything is jamming stuff up if its clear then next is the motors need to be replaced
+Kevys Rc & Music thz so much friend for ur advise. I'll try
your welcome
my helicopter can't moving to far away
what helicopter do you have
Kevys Rc & Music can I pls borrow ur screw driver 😆😆😆
lmao
Hello
Congrats on the video! It really helped me find out if the issue was the helicopter or the receiver.
Once I realized that the helicopter showed "no signal" from the receiver I opened it and.. I have a few toasted transistor, but only on the "LED light box" I am not sure what about to do next!
Would you please take a look at this and tell me if it is repairable?
s25.postimg.org/ln734ehpb/IMG_20140525_134908.jpg
my also not working remote is
youll have to troublel shoot things to find out what went wrong so take it apart and dive in
So what you are really saying is that you were right all along lol
i don't know the helicopter RC name but the model is like a HELIX 1001 the different is the remote control
i know that heli its indoor only and its infared control so very limited range it is what it is and you have to kee the radio pointed at it also keep away from bright lights and dont be pressing the remote for your tv when flying as that knocks them out of the air
hi
hello
I lost a race lost 3 bucks due to the bullshit remote control yesterday.. I'm frustrated..... 😣😣😣😣😥😥😥😠😠😠😠😠😠😠
stuff does happen
Freestyling Brothers
what is my control take a while to connect to the helicopter.......some times the helicopter just move on its own even if the control is off. what could be the problem?
no idea could be weak batteries, could be the radio and heli channels are not 100% in sync