I love it nice and light on the tooling every once in a while got to take the grinder to the striking tools to keep them right love watching ya vids sir
Holy cow Batman. You need tape when caulking next to stucco. Reason being, that he tape acts in two ways, fine lines and a buffer to smooth the tooling knife against the grainy stucco. Brutal
First intro to caulking was at the union facility. Nice, smooth surfaces on the caulking station. Beautiful. First job as an apprentice was control joints and seems on exposed aggregate concrete. Bleh.
Actually on any halfway serious legitimate caulking job That’s A fucken Mess and I’m being kind I would be fired for doing that level of shit as an apprentice
@@elena6516 Did my comment annoy you so much? I think you may have some issues! What does paint thinner do, I'm not aware of that one, but you obviously are. Try to think of something nice to say, it will make you feel wonderful. Have a lovely day.
Honestly it's a bad job by a guy that should know better. Not only is there too much material left, but you can see the transitions and the finish looks all wavy. That's because 1 there's too much material and 2 he starts and stops in the middle of the joint as he tools.
Yessir that’s an absolute disaster where I come from Can’t believe that all these guys doing Horrible Sloppy Shite are making videos and chest thumping like it’s great meanwhile it’s Awful
I first started caulking using my finger, and let me tell you, im like a pro at it. Recently I got a pair of Albion tooling knives and it requires some practice to get good at it.
EVERTHING in all these American caulking videos is Brutal! Guys Wet tooling using Dish soap and finger fucking the caulking instead of tooling? You ever Wet tool Spit on finger or use dish soap and get caught by any inspector who isn’t clueless and you absolutely would be fired immediately where I come from .None of these caulking videos is anything even close to the standards that I had wmaintain and I am not exaggerating when I say that wet tooling or using your finger would be immediately dealt with ( YOURE FIRED!)
Hello, you can find the 922-G01 C.A.T spatulas on our website. Click this link or copy and paste into your browser: albioneng.com/6-piece-c-a-t-spatula-set-stainless-steel-new In addition you can call us at 856.235.6688 to find local distributor.
Caulking knives are pretty hard to find. I always made my own grinding down putty knives etc Those Flexy Albion knives are OK for some stuff but my own much cheaper swap meet tools Finish Way better on big joints and rough stuff
Hi Erick, thank you for your feedback. If you would like to share a video on some of your techniques, we would gladly share it on our social media accounts. Feel free to reach out anytime and follow us on IG @albioneng
This guy is obviously No Pro and is absolutely clueless about what the standards actually are ( or at least were when I caulked) Everyone who criticize him and he challenges them to make a video like it’s So unbelievable that anyone could run the gun and knives better Typical Arrogant American
As a ped door installer this guy caulk good and the wiping down of the caulk is perfect in my opinion. I've seen 100s and installed 100s of doors and anyone that would complain about caulk that looks like that when finished on a exterior ped door is just looking for something to bitch about
Don’t know where you are with the No Standards on caulking but I worked for caulking companies for years and Never saw Anyone even at apprentice level caulk that Sloppy and think it’s okay. I don’t know about anyone else but caulkers ( real bonafide ones) are extremely picky and fussy about even the slightest little knife mark that has nothing to do with the seal. Caulking used to be a really high standards specialty skill but not anymore apparently in No StyUSA
Those would never pass. Especially when they're entrances. Everyone is going to see them. The lines are absolute doo doo and the finish looks all wavy. But it was pretty good shooting.
Actually he took forever with that battery gun Id run and knife that simple thing in a fraction of the time and it would look way better ( which really isn’t saying much)
What were you dipping your C.A.T. into? Is that a secret? Soap? This video was a little frustrating. Seems your goal was more like show and tell. Gives me a bad feeling about Albion products.
Hi Michael, Looks like Wayne was using another spat to scrap off the excess from the spat he was using. Hope that helps. Give us a call if you have any other questions or concerns.
Everybody can do it better but they ain't posting no videos... he's decent ... been in the glazing biz for 20 years ..outta 8 companies I've been to I probably know 6 people that can actually caulk and tool worth a dam... everybody talks the talk...but can they caulk the caulk?? Doubt it.
I am an amateur and getting ready to caulk for the first time. I thought backer rods are for filling cracks so that you only have to apply a thin layer of product. How would you use a backer rod when caulking around a door? Thanks for any advice and tips (:
@@bensosnowski1128 typically yes. Backer Rod is meant to be bond breaker, allowing the sealant to adhere to side walls of the joint and not the bottom. This allows the sealant to expand and contract with without releasing it from the sides, maintaining a tight seal. Check out this blog post for more: www.armacell.us/en/blog/post/are-backer-rods-necessary/#:~:text=First%2C%20backer%20rod%20acts%20as,sides%2C%20maintaining%20a%20tight%20seal.
![FendiDa Rappa - Clock Dat ft. Shamar Marco [Official Music Video]](http://i.ytimg.com/vi/3NBU8KHdxYY/mqdefault.jpg)
My homeboys a union carpenter !!! Boston union carpenter here … I visited the hall in Los Angeles a few years back …. Great job on the video my man!
I like Wayne. I bet he orders extra rounds of “J”alapéno Poppers for everybody on special occasions.
I would get fired if my joints looked like that!!!
Novice here, what should they look like?
Yeah okay scab
@@MisunderstoodWierdo LMAO 🤣🤣
Brutal. Must have been the second time caulking
I think anyone would get fired caulking like that! I hope it's not the main entrance.
I love it nice and light on the tooling every once in a while got to take the grinder to the striking tools to keep them right love watching ya vids sir
Holy cow Batman. You need tape when caulking next to stucco. Reason being, that he tape acts in two ways, fine lines and a buffer to smooth the tooling knife against the grainy stucco. Brutal
Hi Edward, Thank you for your feedback. Please feel free to send us a video or photos of your process.
@@AlbionEngineering
I’m a glazier, so next time I get an exterior caulk job next to stucco your on.
@@edwardcomiskey6556 still waiting on that video
@@edwardcomiskey6556 homie must have gotten permanently laid off lol
@@MisunderstoodWierdo
Actually I own two businesses so little time to take videos. But you sound like you have plenty of time.
Nice job sir
Beautiful
Thank you Garris.
But only to Hellen Keller
HA! You thought @Albion 👆🏼
???????????????????????????????????????????????????????????????????????????????
No it’s not It’s actually completely unacceptable by caulkers standards
First intro to caulking was at the union facility. Nice, smooth surfaces on the caulking station. Beautiful.
First job as an apprentice was control joints and seems on exposed aggregate concrete. Bleh.
Sorry man don’t look to good here in Indiana wouldn’t fly at my company we’re union
EIFS manufacturers all say you cannot put sealant on the finish coat, only to base coat.
Yes I agree
What Oz is that?
He wouldn't get paid if he did that to my building. What a dork.
How long do ya get while using the battery fitted gun on a 50 foot till caulking a 5/8 gap
If you tape it or back tool it it would look a lil nicer. But your way works fine great job keep up the good work
Thanks 👍
Actually on any halfway serious legitimate caulking job That’s A fucken Mess and I’m being kind I would be fired for doing that level of shit as an apprentice
There is enough sealant around that door to do the whole house including the bathrooms
yeah this isn't a house this is a commercial building go sniff some paint thinner
@@elena6516 Did my comment annoy you so much? I think you may have some issues! What does paint thinner do, I'm not aware of that one, but you obviously are. Try to think of something nice to say, it will make you feel wonderful. Have a lovely day.
Not the worst I've seen but close. Must be filling in for the regular guy that out with covid.
Honestly it's a bad job by a guy that should know better. Not only is there too much material left, but you can see the transitions and the finish looks all wavy. That's because 1 there's too much material and 2 he starts and stops in the middle of the joint as he tools.
Yessir that’s an absolute disaster where I come from Can’t believe that all these guys doing Horrible Sloppy Shite are making videos and chest thumping like it’s great meanwhile it’s Awful
That's not a caulk joint to be proud of.
holy shit that would get me fired if my boss seen shit beads like that horrendous wouldn't get away with that in scotland
Can you describe how it is supposed to look? Did they apply too much/little product?
Hi everyone. I’m in Sydney do anymore know where can I learn ? Thank you
I first started caulking using my finger, and let me tell you, im like a pro at it. Recently I got a pair of Albion tooling knives and it requires some practice to get good at it.
EVERTHING in all these American caulking videos is Brutal! Guys Wet tooling using Dish soap and finger fucking the caulking instead of tooling? You ever Wet tool Spit on finger or use dish soap and get caught by any inspector who isn’t clueless and you absolutely would be fired immediately where I come from .None of these caulking videos is anything even close to the standards that I had wmaintain and I am not exaggerating when I say that wet tooling or using your finger would be immediately dealt with ( YOURE FIRED!)
ARE YOU SERIOUS ? YOU THINK IS A GOOD WORK??
Excellent
Thank you for watching
Where can I get those things to smooth the edges? Haven’t seen those in my hardware stores
Hello, you can find the 922-G01 C.A.T spatulas on our website. Click this link or copy and paste into your browser: albioneng.com/6-piece-c-a-t-spatula-set-stainless-steel-new In addition you can call us at 856.235.6688 to find local distributor.
Caulking knives are pretty hard to find. I always made my own grinding down putty knives etc Those Flexy Albion knives are OK for some stuff but my own much cheaper swap meet tools Finish Way better on big joints and rough stuff
Where is backer rod ?
Need tape
You should let a pro to show how is done right
Hi Erick, thank you for your feedback. If you would like to share a video on some of your techniques, we would gladly share it on our social media accounts. Feel free to reach out anytime and follow us on IG @albioneng
This guy is obviously No Pro and is absolutely clueless about what the standards actually are ( or at least were when I caulked) Everyone who criticize him and he challenges them to make a video like it’s So unbelievable that anyone could run the gun and knives better Typical Arrogant American
As a ped door installer this guy caulk good and the wiping down of the caulk is perfect in my opinion. I've seen 100s and installed 100s of doors and anyone that would complain about caulk that looks like that when finished on a exterior ped door is just looking for something to bitch about
I agree it looks fine. Some people say to mask it but that takes a lot of extra time.
Don’t know where you are with the No Standards on caulking but I worked for caulking companies for years and Never saw Anyone even at apprentice level caulk that Sloppy and think it’s okay. I don’t know about anyone else but caulkers ( real bonafide ones) are extremely picky and fussy about even the slightest little knife mark that has nothing to do with the seal. Caulking used to be a really high standards specialty skill but not anymore apparently in No StyUSA
@@senyashchukin391Believe me, No Real caulkers ever tape anything
Those would never pass. Especially when they're entrances. Everyone is going to see them. The lines are absolute doo doo and the finish looks all wavy. But it was pretty good shooting.
Hi Dani Thank you for watching our video and for providing some feedback. You are always welcome to submit videos to service@albioneng.com
Actually he took forever with that battery gun Id run and knife that simple thing in a fraction of the time and it would look way better ( which really isn’t saying much)
@@toecutter1015trippin
what is that? 🤯
Thanks for watching
What were you dipping your C.A.T. into? Is that a secret? Soap? This video was a little frustrating. Seems your goal was more like show and tell. Gives me a bad feeling about Albion products.
Hi Michael, Looks like Wayne was using another spat to scrap off the excess from the spat he was using. Hope that helps. Give us a call if you have any other questions or concerns.
Wet tooling and Shit caulking and An Albion representative?? Wow
The Avatar Albion Engineering fooled me. It is not and engineering's caliper at all. The final product was bumpy and un even width. No.....
Hi Dien, sorry if you had a bad experience, please email us the full details at service@albioneng.com.
It looks like shit and that’s being kind
Everybody can do it better but they ain't posting no videos... he's decent ... been in the glazing biz for 20 years ..outta 8 companies I've been to I probably know 6 people that can actually caulk and tool worth a dam... everybody talks the talk...but can they caulk the caulk?? Doubt it.
I don’t know where you’re from but if you guys caulk like that then smh
Idk.......is *anything* really perfect?
Ummm... would've been better with tape.
Good tip and we can see how tape could be helpful, thank you for sharing.
I’m a professional caulker, have you ever heard of open cell backer rod? You’re not supposed to pump the joint with SikaFlex like that. Do better bro.
I am an amateur and getting ready to caulk for the first time.
I thought backer rods are for filling cracks so that you only have to apply a thin layer of product.
How would you use a backer rod when caulking around a door?
Thanks for any advice and tips (:
Hi Mike, thank you so much for your feedback. We would love to see some of your work, feel free to share your handle so we can follow you.
@@bensosnowski1128 typically yes. Backer Rod is meant to be bond breaker, allowing the sealant to adhere to side walls of the joint and not the bottom. This allows the sealant to expand and contract with without releasing it from the sides, maintaining a tight seal. Check out this blog post for more: www.armacell.us/en/blog/post/are-backer-rods-necessary/#:~:text=First%2C%20backer%20rod%20acts%20as,sides%2C%20maintaining%20a%20tight%20seal.
send this guy back to school A1 is caulking is horrible
NOT CONVINCE IT ALL WITH THIS CAULKER, THOSE JOINTS LOOK LIKE CRAP, NOT SMOOTH IT ALL,
SMH. Not sure you should be doing tutorials on something you obviously didn't learn to do correctly.
Hi Cody,
If you have some tips you would like to share, please feel free tag us a video or post.
Bruh we are working not taking videos for RUclips
Build a better building so we don’t have to fill these fucking canyons.