DIY - 2013+ Cadillac ATS: How To Remove Your Front Bumper by Mishimoto

In this DIY, Rob shows you how to remove the bumper on your 2013+ Cadillac ATS.
Aside from a multitude of fasteners, removing the bumper on the ATS is a simple and straightforward process, requiring only a few simple hand tools.
As always, feel free to follow along and leave a comment with any questions!
Engineering: engineering.mishimoto.com/
Facebook: / gomishimoto
Twitter: / mishimoto
Instagram: / mishimoto

[@titusshelton2447]

VERY GOOD VIDEO

[@michaelkramer8850]

Would love to see a video of removing the rear ATS bumper

[@chasechevy8933]

Nice tutorial! Just what I needed 😁

[@bluesaleen2003]

I have a 2016 Cadillac ATS-V that headlight was damage. Thank you for this video.

[@yrvanmichel1446]

This video is love. Thanks guys

[@dankgotembands2291]

Thank you I really needed this video

[@jesusrosales9263]

Clearly and perfect 👍. You are number One ☝️. Thank you

[@jeffreycollins116]

I’d like to see a video of replacing a fan for the Cadillac ATS 2013

[@jamesjennings3139]

I have a mesh bolt over grille for a 14 ats would this be the best way to install by taking the bumper off

[@0seguidores]

The 2014 ATS 2.0T Grill, haves a vent hole with motor?

[@Derikimi]

Thanks

[@josecarlos-wk7cv]

Do you have to take the whole ft bumper to take the grill off?

[@James-rm4xt]

Does a 2018 ATS bumper fit this year

[@sabinorodriguez599]

2016 xts cadillac front bumper will not stay connect to front right fender.It snaps out after a couple of days.

[@gabylopez6815]

Can you put an ATS bumper on an STS Cadillac both 2009?

[@clarencedelaney6408]

I would love to see anything XTS is the ATS the setup?

[@mishimoto]

We unfortunately have not worked with an XTS so we can't say for sure the process will be similar.

[@SoopaDupa9]

Hello Sir
Can you do a segment on Repairing a coolant temp sensor for a 2013 Cadillac ATS 2.0?

[@mishimoto]

We don't do too many DIY videos outside our product install videos. However, we would be happy to get that added to the list of suggestions for future videos.

[@SoopaDupa9]

@@mishimoto thank you. Do have a video on taking the engine block apart

[@maxkozlov1567]

Is the 2014 bumper same as the 2015 bumper

[@sdhoward8839]

My wire harness would not budge. I didn’t see it in your video but my 13 has a red tab that slides up and down but again couldn’t disconnect. Any advice?

[@mishimoto]

Hello S Howard. Thanks for reaching out. If it is not something that was seen during our installation video, it is very likely our vehicle did not have that option. However, we would be happy to assist to the best of our ability. I'd suggest taking a photo of the connection your having an issue with, and providing a brief description of your problem. Send this information in an email to [e-mail] and we would be happy to help out in any way we can.

[@sdhoward8839]

Mishimoto Automotive thanks for the reply. I figured it out. It was just on very tightly

[@Soccermania517]

You have to push down on the black tab next to the red one you’ll here it click when you press on it

[@KarterboyTUBE]

Would this same procedure work for 2014 CTS?

[@mishimoto]

We do not show that this will fit the CTS models. Sorry!

[@JayOh-]

Can we swap a 2015 at a bumper on a 2014 model?

[@mishimoto]

This is not something that we have tested

[@tjsworld2338]

I have a 2015 ATS do I need to remove the bumper to replace the front emblem

[@mishimoto]

You should be able to simply remove the grill to remove the front emblem

[@awwlove0]

I have the same issue

[@tjsworld2338]

@@awwlove0 just use a flat head screwdriver or trim tool and pry the emblem off. You will break the emblem but the new one will snap in place. I’ve done it twice

[@juliealiza9296]

Radiator

[@katedwyer7544]

First!