Great video! Thanks os sharing. I have a very similar ressue switch that I need to put back together and this video should really help. One question though. There was a small plastic piece sitting next to the switch cover at 02:40, but not sure where did it go. I did not see you putting that piece in the assembly.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Black glove used to assemble black colored parts. You trying to camouflage the whole thing. Also most of the work is completed off to the side of the screen.
You have extra long screws to hold the switch to the plate. There's no room for the thickness of twist ties with the shorty screws on what I have. If you're watching the video it's obvious the plastic piece has to go in first and he had to take it apart to put it in. After multiple attempts using various methods, it was a thin wire that worked for holding things together and still being able to remove it. I also drilled a hole and wired the back end of the pressure plate. That's the critical part that always wants to pop out when you're trying to put it together. What a PITA I finally got it working like new. The problem was the gasket leaking air and now it doesn't.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Thank you, I spent a lot of time trying to get this contraption together. Nearly drove myself nuts. Your technique solved the mystery for me. After taking this thing apart and ordering a new switch I realized it was just a simple reset button on the motor. I put it all back together following your technique and all works great. As one of your viewers noted the black plastic piece goes in Pryor to the spring attachment. Plastic ties and vise grips were the secret 👍 Have a backup pressure switch and thorough knowledge of what to do now. 🤬🤬🤬now🥰🥰🥰 Thanks again.
Nunca míre cuando fue que me introdujiste el plástico negro con pequeño resorte que al principio lo miré en la mesa .. gracias como quiera ahora ya tengo una idea tarde unas horas y no lo logré poner .
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Thank you for always sharing videos that give the audience a new perspective and true image of you and the place you want to convey. I am sure, you already have a loyal audience, including me, who love the authenticity of each video. Keep moving forward and work hard every day, I will always watch full videos with ads to support you
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Great job galing nman.Thanks for sharing
like 542 idol..nice sharing.done watching❤
so, where does the black plastic piece go that seemed to disappear around 3:40...
I think that should have been the first thing to go in!!!
Amen slight of hand but no help smh
I came here to say the same thing. 😳
@@jamesdaul8540It slides in vertically and part of it stick out the top of the housing (reset button). Only goes in one way.
kailangan talaga marunong angg kabit ng ganyan buti nkita ko vedio mo maramong salamat
Great vedios
Wow galing nyu sir bagong kaibigan po
Tenx sa tulong boss
Great video! Thanks os sharing. I have a very similar ressue switch that I need to put back together and this video should really help. One question though. There was a small plastic piece sitting next to the switch cover at 02:40, but not sure where did it go. I did not see you putting that piece in the assembly.
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Thank you so very much. Much appreciated.
Eto yung nakatulong sakin ngayon. Maraming salamat po
Awesome 👍
I could not get this switch back together without this video. Thank you for posting this!
I took mine apart and damn it went everywhere… couldn’t figure it out.. maybe this video will help.
Amazing video Have a Good time
Tamslab watching my dear friend nice Gling mag assemble great sharing
Lots of Thanks
🎉🎉🎉
I solved da problem 4m yo video.
Thanks 👍👍👍
Welcome 👍
Galing lods thanks for sharing napaka husay ng pag kakagawa at napaka pulido ❤❤❤
Nice sharing host , really you're expert in this mechanical electronics
2:58 you have the black plastic peice with the odd shape l. Where did you put that..
Good morning thanks idol for sharing this video stay connected
L431 idol. maraming salamat sa pagbahagi ng iyong kaalaman at kakayahan, kabisado mo talaga lods
Hello sir watching replay here . Thank you for sharing this tutorial video. Thank you for sharing and visiting my house. Stay connected. God bless.
Magandang pagbabagi ng iyong video 🎉magandang panoorin hanggang sa wakas at para itoy suporta din nilang kaibigan
Nice sharing lods watching full
thanks for sharibg lods
Salamat sa pagbahagi idol malaking tulong ito.. God bless mabuhay ka..
Thank you so much for this video , I would have been screwed without it.
thanks for sharing kung paano mag assemble..
Wow nice sir
Watchiing kabayan..salamat sa pah share ng video
Ngayun may idea na ko lods. Salamat
Nice lods galing....
I like how you cut the film and then put the plastic piece in that you forgot to put in in the beginning lil shady I didn't watch anymore🤨👎
😅😅😅
Did you catch him with his pants down?
I came here for this same comment. 🤷🏼♂️
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@@jerryayers7337amen ❤
Good work assembled host ang galing
Good job
Thanks
Thank you for sharing po.
Black glove used to assemble black colored parts. You trying to camouflage the whole thing. Also most of the work is completed off to the side of the screen.
Thanks for sharing your ideas
Galing naman idol.thanks for sharing.God bless
Again watching your video friend.nice sharing.❤❤❤
Great help po. Thank you for sharing.
رااااااائعة رااااااائعة بزاااف يا اخي عزيز دائما تواصل معك يا احلى واجمل قناة 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
WOW so nice... Good job.... Thank you for sharing...
Watching fullpack po
Great tutorial, thank you for the knowledge you shared..👍 full watched... Have a wonderful day my friend
Great knowledge
Thanks for sharing your expertise. Great jo👍
You have extra long screws to hold the switch to the plate. There's no room for the thickness of twist ties with the shorty screws on what I have. If you're watching the video it's obvious the plastic piece has to go in first and he had to take it apart to put it in. After multiple attempts using various methods, it was a thin wire that worked for holding things together and still being able to remove it. I also drilled a hole and wired the back end of the pressure plate. That's the critical part that always wants to pop out when you're trying to put it together. What a PITA I finally got it working like new. The problem was the gasket leaking air and now it doesn't.
Informative, great tutorial! Job well done, keep on sharing your knowledge , ha e a great time, enjoy!
sir the small black plastic.where did you put it...
It goes iside,its the little button on top you push down, that's the part that had me stumped
He edited because he fucked up he had to do it all over again
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
galing mo lods
Thank you so much for this video. I am fixing up a Craftsman air compressor and it has a very similar switch. Using the Vise Grips was genius!!
Thanks for your help! If it would have flew apart slower, maybe I'd seen where everything went!
Ayos Lodi nice content keep vlogging po god bless
Assembly air compressor pressure switch , good
Thank you,
I spent a lot of time trying to get this contraption together.
Nearly drove myself nuts.
Your technique solved the mystery for me.
After taking this thing apart and ordering a new switch I realized it was just a simple reset button on the motor.
I put it all back together following your technique and all works great.
As one of your viewers noted the black plastic piece goes in Pryor to the spring attachment.
Plastic ties and vise grips were the secret 👍
Have a backup pressure switch and thorough knowledge of what to do now.
🤬🤬🤬now🥰🥰🥰
Thanks again.
Nunca míre cuando fue que me introdujiste el plástico negro con pequeño resorte que al principio lo miré en la mesa ..
gracias como quiera ahora ya tengo una idea tarde unas horas y no lo logré poner .
Thanks for this video. I learned.
Galing mo nman sir
Thank you❤️❤️❤️ for sharing and try to fix also
Thanks but you didn't install the black plastic piece before you put zip ties on, did you forget and have to start over?
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
L350 you are so very skilled hand ,sir. Good job❤
There is a little black part with 2 little sticks, u dont show up where go!!
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
@@jerryayers7337thank you
Thank you for always sharing videos that give the audience a new perspective and true image of you and the place you want to convey.
I am sure, you already have a loyal audience, including me, who love the authenticity of each video.
Keep moving forward and work hard every day, I will always watch full videos with ads to support you
nice
This video is very helpul and informative good content bro
Desejo muito sucesso pra você 🤝🙏
I am assembling the pressure switch but stumped with the black piece of plastic..you have it on the table and than it disappears
Not sure where it goes in the switch please help
So smart to use plastic ties!
Brother cortaste el vídeo en el minuto 3:42 para mi es muy importante saber dónde y cómo va la pieza de plástico
BOM TRABALHO. DEUS TE ABENÇOE GRANDEMENTE
Where did put that black plastic???
Where did the black plastic piece go it just disappeared
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
Intinya dari pemasangan ada pada tang jepit dan tali tis kalo gak pake itu auto susah si Per dan pelat nya mental
Yeah... that's something I hope to never do again. Many new curse words were invented.
Damn music
where did the plastic peace go. most important part of the assemble
It slides in vertically and part of it sticks out the top of the housing (reset button). Only goes in one way. And yes, it's the first thing that should go in.
your still hiding u forgot to insert the plastic switch , such a crap assembling
Sir may nabibili Po bang automatic adjuster Yung plastic Po Yun en nabasag kc Po Yung plastic adjuster
Wala sir kuha ka na lng sa mga sirang unit o bile ka n lng ng bago
Unfort it didn’t work for me. Wire tie got stuck and the bottom lip slipped out. I’m just gonna buy a new compressor.
nakalimutan mo po ang itim una ilagay
I just come to comment on the reset button that you forgot.. then it mysteriously isn't on the table anymore??? 😢
tanggal ka ulit kasi yung itim na nilalagay sa loob di mo inlagay
You forgot reset
Neumíš to