I don’t know, but Dodge says different. It’s says 44 inch pounds a seat injector in. Then loosen Bolt bolts put feeder Or crossover tube and torque nut 11 inch pounds. Then torque injector final torque is 89 inch pounds. Go back to crossover tube and final torque is 37 to 45 Ft. lbs. Way it gets evenly torqued by a fourth step Torquing process. Thank you for the video I like your old video but that’s straight outta Dodge.
It is 11 ft lbs (not in lbs), but yes, sequence from the manual makes more sense for getting the crossover tube aligned to the injector notch. 11-inch pounds is for the solenoid nuts (in 2006 manual).
Thank you for the video! It helps me finally understand how the high pressure fuel seals into the injector body via the feed tubes. Great explanation on torque sequence. Your videos are helpful for guys like me. Keep them coming!
My 2006 tube hold down is 57 ft lbs not 34 ft lbs and 11 in lbs on the harness nuts not 13 in lb, great video just wanted to note the difference from my dodge service manual
I think I would go with your service manual. I worked for Dodge for quite a few years. And the guy that taught me raise three kids through grade school and high school Catholic private schools working nothing but dodge Cummings.
Is there a way I can send you guys a video of my 06 Cummins to my it sounds funny but it mite be in my head it’s new to me so any little tap or sound I look into it deep
You mentioned using petroleum jelly for injector seals and then said grease on tube rings, did you mean petroleum jelly on tube as well or grease? Thank you.
I want to say anything will work here, but I'm sure someone will jump in and say “don’t use X grease blah blah”. We traditionally use assembly lube or just everyday bucket of high temp bearing grease.
I replaced all of my 06 injectors about 2015 when #6 went bad. I was a cheapskate and didn't replace connector tubes. My #5 injector just went bad so I ordered one, plus 6 connector tubes. Would you recommend replacing all 6 tubes? My truck has always started and ran well. I was, however, disappointed ever since I replaced all 6 injectors in 2015 (160,000 miles- truck now has 200,000)it has gotten a few less miles per gallon whether towing, empty, city, highway, etc.
@@thoroughbreddiesel how would you recommend I replace the other 5 since those injectors don't need replaced? Remove old tubes, brush inside the hole clean, replace and torque the connector tube nut? Or loosen the injector bolts then insert and torque the new tubes? Or even more than that, pop injectors out and then push back in as if I am putting in all new ones, then install connector tubes?
@@thoroughbreddiesel yes common rail. I've been checking seems like some tubes port to injectors are crushed and one injector looks like double o ring. This was done by a diesel mechanic guess he's NOT
@@thoroughbreddiesel I got it running real good. Now I think stuck injector knocking and smoking white. I have the cap to block off fuel to injectors but no rail fuel pressure but there's fuel coming out of the rail what is going on now?
You have the suspected injector line removed and capped off? If so and it doesn’t stop knocking you move to a different cylinder. I don’t think I understood exactly what you are saying.
@@thoroughbreddiesel I'm moving to a different Cyl. My question if an Injector is stunk would it cause no fuel pressure at the rail because that's what's going on
This video is for a common rail truck (Model year 2003 +). If you truck is a 98.5-02 truck and you have a no start, check lift pump pressure and codes to identify your problem.
I apriciate the video" I just recently replaced all 6 of my injectors with remanufacured bosch injectors from a reputable e-bay dealer. I had 1 of them stay completely open causing an engine knock and clouds of white smoke. I was able to isolate #2 was the cause with the miller cap tools. I pulled it, put back in one of my old ones and now I'm at the point I have put back all my old ones and my truck will not stop smoking when I give her gas. there is no blow bye/blow back she idles perfect drives like she used to, but now I have white smoke and when I place a heavier load on her I get a cloud of grey smoke. any sugestions?
I think you are on the right track. Pull all injectors and send them back. I would also suggest running a compression test on the motor because the faulty injectors could have done some engine damage.
Dont forget to blow out the hold down bolt holes! extreamly important
I don’t know, but Dodge says different. It’s says 44 inch pounds a seat injector in. Then loosen Bolt bolts put feeder Or crossover tube and torque nut 11 inch pounds. Then torque injector final torque is 89 inch pounds. Go back to crossover tube and final torque is 37 to 45 Ft. lbs. Way it gets evenly torqued by a fourth step Torquing process. Thank you for the video I like your old video but that’s straight outta Dodge.
It is 11 ft lbs (not in lbs), but yes, sequence from the manual makes more sense for getting the crossover tube aligned to the injector notch. 11-inch pounds is for the solenoid nuts (in 2006 manual).
Thank you for the video! It helps me finally understand how the high pressure fuel seals into the injector body via the feed tubes. Great explanation on torque sequence. Your videos are helpful for guys like me. Keep them coming!
You're very welcome!
My 2006 tube hold down is 57 ft lbs not 34 ft lbs and 11 in lbs on the harness nuts not 13 in lb, great video just wanted to note the difference from my dodge service manual
I think I would go with your service manual. I worked for Dodge for quite a few years. And the guy that taught me raise three kids through grade school and high school Catholic private schools working nothing but dodge Cummings.
Great video! It looks like you take a lot of pride in your work, which is nice to see :)
M oki 9k oh 3988l9k0 OP k I'll k.kk.
amazing video thx man
Awesome thankyou so much,, really helped! !!!!
Thank you for the kind words. This is why we make them.
Please can you explain to me how to identify the negative and positive terminal on a common rail injector when the cable color are the same.Thanks
Is there a way I can send you guys a video of my 06 Cummins to my it sounds funny but it mite be in my head it’s new to me so any little tap or sound I look into it deep
You mentioned using petroleum jelly for injector seals and then said grease on tube rings, did you mean petroleum jelly on tube as well or grease? Thank you.
Petroleum jelly will work fine
Who needs to go college for it and pay for books,just switch to you tube 90 percent of learning is done with the eyeballs.
That's riigghhtt!!
sir..help me why my starex crdi no start without fluid starter what is ta common reason..and how to solve the prob..pls help me?
Had dealership do this for me. They also charged me $700 for a new manifold cover. They said they are not reusable . I'm suspicious. What's the truth.
they likely broke the cover. totatlly reusable.
Is the 6.7 the same torque specs. as described in this video?
No
What type of grease, lithium, ball bearing, Vaseline, gear etc?????
I want to say anything will work here, but I'm sure someone will jump in and say “don’t use X grease blah blah”. We traditionally use assembly lube or just everyday bucket of high temp bearing grease.
what torque wrench are you using for the inch pounds? I can't find anything but torque wrenches in Ft/lbs
Mac tools snap on and harbor freight have them
It’s a snap on ¼ inch drive, they read inch pounds. Most of todays newer digital torque wrenches will display inch pound too.
I need you help please I have a 5.9 Cummins injector problem
Give us a call 1-859-737-4966.
I replaced all of my 06 injectors about 2015 when #6 went bad. I was a cheapskate and didn't replace connector tubes. My #5 injector just went bad so I ordered one, plus 6 connector tubes. Would you recommend replacing all 6 tubes? My truck has always started and ran well. I was, however, disappointed ever since I replaced all 6 injectors in 2015 (160,000 miles- truck now has 200,000)it has gotten a few less miles per gallon whether towing, empty, city, highway, etc.
Replacing the feed tubes wont hurt a thing, and one thing that may be good for the entire project is to have those tubes retorqued.
@@thoroughbreddiesel how would you recommend I replace the other 5 since those injectors don't need replaced? Remove old tubes, brush inside the hole clean, replace and torque the connector tube nut? Or loosen the injector bolts then insert and torque the new tubes? Or even more than that, pop injectors out and then push back in as if I am putting in all new ones, then install connector tubes?
I've changed my injectors now has that loopy idle, what did I do wrong??
Common rail dodge? Check feed tubes.
@@thoroughbreddiesel yes common rail. I've been checking seems like some tubes port to injectors are crushed and one injector looks like double o ring. This was done by a diesel mechanic guess he's NOT
@@thoroughbreddiesel I got it running real good. Now I think stuck injector knocking and smoking white. I have the cap to block off fuel to injectors but no rail fuel pressure but there's fuel coming out of the rail what is going on now?
You have the suspected injector line removed and capped off? If so and it doesn’t stop knocking you move to a different cylinder. I don’t think I understood exactly what you are saying.
@@thoroughbreddiesel I'm moving to a different Cyl. My question if an Injector is stunk would it cause no fuel pressure at the rail because that's what's going on
5.9 Cummins cranking but dont start. How do I know if it's the VP44 or the injectors, or anything else?
This video is for a common rail truck (Model year 2003 +). If you truck is a 98.5-02 truck and you have a no start, check lift pump pressure and codes to identify your problem.
I apriciate the video" I just recently replaced all 6 of my injectors with remanufacured bosch injectors from a reputable e-bay dealer. I had 1 of them stay completely open causing an engine knock and clouds of white smoke. I was able to isolate #2 was the cause with the miller cap tools. I pulled it, put back in one of my old ones and now I'm at the point I have put back all my old ones and my truck will not stop smoking when I give her gas. there is no blow bye/blow back she idles perfect drives like she used to, but now I have white smoke and when I place a heavier load on her I get a cloud of grey smoke. any sugestions?
I think you are on the right track. Pull all injectors and send them back. I would also suggest running a compression test on the motor because the faulty injectors could have done some engine damage.
@@a0f58c oil creating white smoke LOL
@@a0f58c ummmmm,,,,most of the engines that burn oil had blue smoke,,now injectors leaking fuel i'v seen smoke white,,