I just purchased a KTM Duke 200. I would like to put BL6 LEDs on the front and rear. What part numbers do you recommend I purchase on your website? I know the part number for the BL6 lights, but I would like to know other connectors and relay that you recommend I purchase to go along with them. Thank you!
In the product page on our website we have a photo closeup of our harness converter connector as well as the corresponding receiving connector on the bike side. There should be no ambiguity once you take a look at that photo on our website. If your connector look like what we have pictured then you are good to go. If they do not look the same then they aren't compatible.
Dude...i don't know how this wasn't apparent from my intro. This is a video installation instruction for products we manufacture and sell at TST Industries. The link is in the declscription of the video.
Is there a separate relay for the rear turn signals? If I replace my rear turn signals only, do I just replace the relay in the front to readjust the turn signal rate?
@@pepe_valaz you shouldn't need any additional parts. If you purchased our harness converters along with the Mech-EVO lamps then the wiring scheme is lamp-red to harness-black, lamp-brown to harness-yellow. The blue will remain not connected unless you get the running light connection kit and are willing to install that to a switched/fused 12v supply (like head lamp circuit). In the future please consider contacting our cuustomer service department through pur website for timely help. Our RUclips staff does not typically do support.
We have not had one in the shop yet. By all reviews we have seen the bike is pretty much identical to the KTM model, but I can't hang my hat on it. Where are you located? Are you local to Lake Helen, FL? If you bring us the bike for verification I will give you the parts for free. The signal lamps themselves will most likely fit because they are universal. I just don't know about the connectors and relay.
According to the review comment on the TST website, these signals worked just fine on a customer's '22 Husqvarna 701. Said "plug and play." The flasher relay too.
@@TSTindustries i know you have told me that before. I really think you should tho. Theres only one aftermarket brand for my bike and its chrome compared to the smoked stock one. The stock ones a known to snap at the mounting place. Mine did at 2000 miles so now i just have it zip tied on😕 i refuse to buy the chrome one tho.
I seriously lost a little bit of respect for you guys after seeing you fudging that 2 pin connector into your 3 pin STYLE relay. You know what Im talking about. I WAS considering purchasing from you.
That's cool. We can't just whip up an entire relay, with a dedicated connector on it, the molding tool that makes the connector, etc in two days. That bike was in the shop for only a few days. We came out with a relay that fits that socket two months later
As the body parts and configuration IS significantly doffernt from smc vs enduro it SUCKS anyone making it appear otherwise.....THUMBS DOWN...do SEPERATE videos!
Will the front plug n play turn signal connectors work for the rear
I just purchased a KTM Duke 200. I would like to put BL6 LEDs on the front and rear. What part numbers do you recommend I purchase on your website? I know the part number for the BL6 lights, but I would like to know other connectors and relay that you recommend I purchase to go along with them. Thank you!
Integrated tail light for 21 smc 690. No stock???? When will they b available?
Would that harness converter and relay work for 2020 duke 200....hard to tell from video or web site if it looks the same
In the product page on our website we have a photo closeup of our harness converter connector as well as the corresponding receiving connector on the bike side. There should be no ambiguity once you take a look at that photo on our website. If your connector look like what we have pictured then you are good to go. If they do not look the same then they aren't compatible.
great vid ! do you know where is the relay on the Duke 690 ? mine is from 2018 and i cannot find it
On the Duke 690 it should be up above the front wheel somewhere around the headlight.
Lo encontraste ya amigo? Yo aun no lo encuentro
Where did u buy the lights, and the connectors? Need it for my ktm 690 smc r 2015
Dude...i don't know how this wasn't apparent from my intro. This is a video installation instruction for products we manufacture and sell at TST Industries. The link is in the declscription of the video.
Is there a separate relay for the rear turn signals? If I replace my rear turn signals only, do I just replace the relay in the front to readjust the turn signal rate?
It is just one relay for front and rear.
My front signal wires are red brown and blue. How do I wire them?
If you are referring to our Mech-EVO signals or our Quadrix signals, the wiring breakdown is below.
• Red - Ground
• Blue - Running
• Brown - Signal
@TSTindustries Sorry yes the Mech-Evo signals. So wire brown to black
Blue to yellow?
Does anything else need to be purchased for them to work?
@@pepe_valaz you shouldn't need any additional parts. If you purchased our harness converters along with the Mech-EVO lamps then the wiring scheme is lamp-red to harness-black, lamp-brown to harness-yellow. The blue will remain not connected unless you get the running light connection kit and are willing to install that to a switched/fused 12v supply (like head lamp circuit). In the future please consider contacting our cuustomer service department through pur website for timely help. Our RUclips staff does not typically do support.
Would this fit on a gasgas sm 700 ?
We have not had one in the shop yet. By all reviews we have seen the bike is pretty much identical to the KTM model, but I can't hang my hat on it. Where are you located? Are you local to Lake Helen, FL? If you bring us the bike for verification I will give you the parts for free. The signal lamps themselves will most likely fit because they are universal. I just don't know about the connectors and relay.
is the relay compatible with all ktm model? duke 200?
No, but our RLYG2 model is.
@@TSTindustries where can i get it? any videos about it?
Any chance of you guys doing parts for the Husqvarna 701 Supermoto?
If we get one in-house, absolutely.
essentially it is the same one
According to the review comment on the TST website, these signals worked just fine on a customer's '22 Husqvarna 701. Said "plug and play." The flasher relay too.
Great vid! Would these fit a 2017 Duke 690?
They should fit nbo problem. Please just verify you have the same connectors on your signals as are shown on this bike.
@@TSTindustries Ok, will do. Thanks!
Dudeeee still waiting on the SD1290R tail light! I need one!
We are not likely to make one for that bike.
@@TSTindustries i know you have told me that before. I really think you should tho. Theres only one aftermarket brand for my bike and its chrome compared to the smoked stock one. The stock ones a known to snap at the mounting place. Mine did at 2000 miles so now i just have it zip tied on😕 i refuse to buy the chrome one tho.
Lovely KTM I like the duke690
Good choice
I seriously lost a little bit of respect for you guys after seeing you fudging that 2 pin connector into your 3 pin STYLE relay. You know what Im talking about.
I WAS considering purchasing from you.
That's cool. We can't just whip up an entire relay, with a dedicated connector on it, the molding tool that makes the connector, etc in two days. That bike was in the shop for only a few days. We came out with a relay that fits that socket two months later
@@TSTindustries Ah understood. I found it on your website, I see there are 2 versions.
As the body parts and configuration IS significantly doffernt from smc vs enduro it SUCKS anyone making it appear otherwise.....THUMBS DOWN...do SEPERATE videos!
If we get the chance to get the other model in, sure. We rely heavily on local riders to lend us bikes so getting them isn't as simple as it may seem.