Sambo Digital Speedometer
HTML-код
- Опубликовано: 7 сен 2024
- I know this is a lengthy and I know how to spell dummy, but I just wanted to get this up, I really need this in my rearview mirror.
Waiting on the carb to get going and this stacked behind it has kept me behind the eight ball for weeks....now it's time to enjoy the fruits of my labor.
The drill bit used to slowly cut through the brake disk is a 3/8 Cobalt bit... trust me, just go buy one at Lowes or Home Depot for $12.
The Speedometer.
www.amazon.com...
Hi sir. I bought the exact same speedometer and i found out a way to calculate the setting for the speed sensor in the speedometer.
The instructions say base setting is 42 Hz at 60 km/h. To calculate the setting for the bike you need to know the circumference of the wheel or the diameter*pi.
The setting on the speedo is the frequency of the wheel at 60 km/h.
In my case the circumference is 2,05m (21" wheel with offroad tires, KTM 620 SX)
Setting = (60 / (Wheel circumference in meters /1000)) / 3600
In my case calculated setting is: Setting = (60km/h / (2,05m/1000)) / 3600 = 8,13 Hz at 60 km/h.
I used two magnets on the wheel which means double the frequency.
Setting = 8,13 Hz * 2 = 16,26 Hz.
I put my setting at 16 Hz and the speed is perfectly allign to the GPS.
Hope this is useful for some one out here. Nice video (y).
Best Regards
I was aware that it could be calculated, it was talked about on a forum I belong to. G.P.S seemed a bit easier for the average guy although someone like yourself probably can't understand that because your way is easy enough for you.Thank you for your valuable input and for being nice about it!
I have 90/80 16" front tire, so it should have a circumference of 167,3 cm and the calculation would be (60/(1,673m/1000))/3600 = 9,96 Hz with 2 magnets for speed sensor means 19,96 => 20Hz?
@@foobaar3572 yes thats the way 👍.
@@kasperbs96 Thx! I will try it out hopefully in the next dayz. Over here in Europe we are having a lot of rain these dayz :(
@@foobaar3572 im from Europe as well so i know what you mean 😉. Good luck 🙂
It can be set to run on anything with a wheel really, As long as you have a place to mount the magnet and censer it will read the speed . It has a wide range of adjustment setting in the cluster.
Sir. How to make the clock stable? Everytime i switch the ignition it always reset to 1:00
I put my magnets in the break disk, worked perfectly after I set the size of circumference of the wheel in the speedo
@@matheusteles9184 I'm glad to here it worked well for you, I figure this could be used in a lot of different bikes bbut it is a good bit of work!
Just want to say your a lifesaver, been trying to stop the damn fuel gauge flashing for ages .. my bikes from 92 and it doesn’t have a fuel gauge
Thank you for this video. I have the same speedo on a moded dirt bike that was converted to street legal. The kid I got it from gave me the speedo with it not hooked up and no instuctions at all. I searched the web for proper instructions and found nothing useful until I found your video. I got it working perfect now. Thank you for the help.
That you for taking the time to let me know, I hope that all all this stuff I find interesting and spend the time to put out reaches the right people. I found no real information on the subject also so I went through this in hopes all would be worth it in the end, It's my most viewed video now so I am happy it has helped so many. Thank you all!
Paul Woodruff.
Thanks again there is one thing I found out is the numbers on the unit for dialing in the speedometer represent the size of the front wheel. I have a 17" wheel so set at 17 and it worked.
I have a 19 inch front wheel and it works in a 17 setting so I'm not sure how that worked out. thank you for your comments!
@@projectnext5020 #12 stands for what??
Thanks for posting this. No doubt there are a number of Haosen Hawk & Bashan Broz owners that will benefit. If you ever look into or try alternative seats please post your findings.
I hope it does help the community of China bike riders, we are all kinda cutting a new trail with these affordable fun machines! I'm sure at some point I'll get there with the seat.
Hi guy, i am brasilian and i instal this speedometer in my motorcicle. Good video
Hello from Texas! I'm glad you liked the video and I hope was helpful. Thanks for watching.
THANK YOU! perfect video for me to convert and replace for my ninja 300 Street Fighter!
Glad it helped, Also keep in mind that they make this same speedo thats 10k rpm, this one is 13k. For some reason i have to reset my clock a lot even though I'm tied into constant power.
Thanks, this video helped me so much, mine's came today without instructions, it's another model but the wires are the same.
Glad it helped!
Best instructions I've seen ,thanks.
So man I’m coming to the party a little late but can you explain the pinned connector with all the gears it’s confusing me I got the other I believe. But this one has me stumped........also very random but what kind of background music is that I love it
didu figure out how to pin the gears and neutral im stuck here too
can you help please for some reason my tachometer is at max even without being connected also my gas gauge keeps blinking with it just being connected to the blue and white wire from the bike
Really nice and informative video.
I am in a bind. My bike's LCD display damaged again by condensation 2nd time now! Hence looking for videos on how to install these aftermarket speedo's.
Either fit an OEM which takes 5-10 minutes but cost 400 bucks on that speedo alone.
or use this Sambo one (re branded in our country as Zaddox) at only 50 bucks. Its hell'a cheaper but yes I would have to deal with the Wires, The mounts and the Magnets.
Yes it is a task but $400 is a lot for a speedometer. You can use a GPS speed app on your phone to get by until you decide.
@@projectnext5020 yeah, it really is too much, even the one's that still works but came from a crashed bike are still at 300 bucks.... I could give it a go connecting the aftermarket speedo but having a hard time looking for my bike's wiring diagram. And Yamaha wasn't so keen on giving it to me.
And I do not think it is as simple as allocating the wires on my bike's wires connected to the original speedo into the correct colors on the replacement. I will have to check tomorrow.
You can go to the CSC website and order a fuel tank with the gas gauge if you want to add the fuel gauge.
That was a great video explained everything in detail.Thanks it was a great help . Davy
ruclips.net/video/hwDlgqMCYok/видео.html
Hello! I have connected the speedometer and i am wondering one thing, my bike has original magnetic speed sensor with a magnet installed in the brake disc already. Its possible to use original magnet with chinese speedometer?
any way to stop water temp from flashing without connecting a water temp sensor? and did you use the c clips for the magnets or just glue them in?
Also my tach won't work found out to put a one Kila ohm 1/4watt dioad between switched power source and tach sending wire.
Great Info, I took the signal from my coil signal (LT) with the 1KΩ resistor is series to the line in on the Tachograph because the ECU signal was there but the Speedometer Unit couldn't sense it.
I would like to add a personal experience that may help many. I have installed this meter on My Suzuki GS 150 which has a Front Tyre size 2-75-18 and Meter Config had to be set to 09 12 To Get The Accurate Speed
Hi. I can’t get that calibrating screen ... i tried push botton and then connect it to battery. P.s my bike don’t have built in battery..😔 And also, i didn’t calibrate it, and it dont show any speed..
excellent video.. very informative.. i'm having trouble with the rpm, it is very high and does not match with my bike.. can you help me??.. thanks, really appreciate the answer..
hey got a question on which wire was it to get the fuel gauge to stay full? I WISH I CAN USE IT AS a battery guage on my eletric bike
Great video, thank you. Just have one question. How do you attach those darn magnets to the wheel?
Hello Sir Your Video Helped me a Lot But Can You Please Explain How a Trip Meter is Reset Without Resetri g the Total Mileage. I tried by pressing and holding the right button and then switch on the iginition but it sometimes doesnt work and sometimes it resets both the trip meter and total mileage to zero.
Can You Please Find out the way for resetting the trip meter.
Well explained. Thank you for sharing with us.
Thanks Alot.. this explained everything to me except where to place two magnets on Disc..?? Is it ok if i place two magnets on straight line??
You need to drill a hole in the disk with a hardened cobalt drill bit. anything less and it will just go dull . the disk plate is hardened steel. Actually one magnet should do , I used two but I realized one would have worked.
@@projectnext5020 Thanks 👍👍
II have a digital gauge Chinese I am putting it on I am putting it on a Kawasaki 600 or I'm trying to R I'm trying to figure out the wire color 4-D a color for the RP m's
Nice job on the Speedometer Paul.
Thanks Jerry, I've been around the forums but have had little time to post up anything due to work keeping me tied up but I'll pick it back up in November.
How has the durability been on this unit? Looks like you have had it for a year or so. I seriously considering it for on of my bikes.
Thanks for the great video!
Sir wat color i test f the product is good wat color should i test in battery
Need help hooking this unit up to a drz400sm 2005 model. What I need to know is the colors for each wires that got to the speedometer to the bike 🏍 wires. I am having a hard time trying to figure it all out.
Hi am wanting to put it on my spy f1A road quad I've bought it here in the uk but am not to cleaver on wiring part but am going to give it a go cheers for your video cheers Paul
You should be surprised at how easy it is to figure out, Wiring can seem a bit intimidating until you take a close look at it.
Hopefully going to try it next week need to remove part of my wall to get her in my garden due to the people live on my street don't like it they say it shouldn't be there or and my big works van plus my car so I said to lot of them sorry I have toys and and a work van they don't like me that much but they do when they want me to look at there homes or use my stuff lol
@@brentleajunction LOL, Your just something else they can talk about I'm sure, I just replaced a bike for the neighbor's child. a single mother whose daughter kept messing up her hand brakes on her bike she rode to school everyday, I repaired those brakes at least 4 times before I decide that a replacement was the only way I would shake that recurring job. It's a second hand bike and wouldn't you know I found the only girl in Texas that doesn't like pink bikes! sometimes you can't win.
@@projectnext5020 girl are funny at times lol
my chinese cluster came with the wires labeled. but my bike they are not labeled. for a chinese bike what is the rpm signal wire? and also did you connect the neutral wire from the cluster directly to the top of the coil?
Buenas Tardes¡¡¡ como se puede pasar a color azul en la pantalla del tacometro?
Thank you very detailed video. Now I have to go and install guess I have delayed the inevitable long enough. 🤔
ruclips.net/video/hwDlgqMCYok/видео.html
high--I've just bought a unit and the vid is very helpful--but I have a question--I have two extra wires with bullet connectors apart from the speed input connector (3 terminal), gear number(6 terminal) and the main 9 terminal connector. I'm guessing that these wires (a brown/red and a grey) are for an engine service/fault light--? can you please confirm. I'm hoping that my kawa electronic speedo input(3 wire)--will produce a pulse that the unit will recognise for speed--otherwise its a single magnet. I have checked that the unit requires a permanent 12v (red) and a switched 12V from the ignition (black) to activate the display?
Hello, I bought the same speed meter on my engine, but we could not adjust the calibration, it does not count km and the trip is always 0 my engine is Yamaha xt 600 and the front rim size is 21 "can you help me ...
How do you change colors?
What do the numbers mean?
My says 588 01. The tach works but the speed is a mess. I have 2 magnets.
Where does the "speed signal" wire connect and how many volts goes to it?
If your speedometer is mechanical, you need a converter from analogic to digital. If it is digital, so you need to conect the three wires cable from the Wheel to speedo, or install the 3 wires cable with the 2 or three magnets inthe Wheel yo fer the signal. In few words, there are no voltage needed, Just the 3 wires sensor cable.
Great video sir. Pls help me. What does it min by the first 3 digit??? And where did you get the idea of number 017 on the first 3 digit. Thank you very much
Is anyone else happing a problem with the odometer? Mine doesn't seem to be updating, speedo works fine.
Hi Sir I followed your instructions and now my speed reading is much accurate, but my concern now is when I reached 60kph my reading would start to go down like I know Im running about 70 but my reading shows 50+ hope you can help me out
Did you ever find out what the first 3 numbers are? Doesnt make sense to just choose random numbers for the settings. They mean something. Is it by chance for the tire size?
good evening, i have an atv, a dvx 400, it have 1 cilindre 4 stroke.
I have a problem with this tachometer, where i should connect the rpm wire?and what i should set on the speedometer?
Nice one sir new subscriber here from philipines.
Thanks, my wife was born in Manila.
Hi Roland kumusta dyan sa philippines,salamat pala sa pag-scribe sa channel sa asawa ko.-Liza
Thank you for this video ... I was struggling to calibrate the speedo ...did'nt know how .. all sorted.
I'm glad it helped, Thanks for watching!
Can i ask sir where did you connect the wire for the clock is it directly to the battery? If not any particular positive source? Thanks
Thank you my friend!!!
Any idea on how to set kilometers back to old value? When replaced it goes to 0.
what does each of the number represent
hi sir im from philippines, great vid.you sir helped us alot.bt i only have one problem right now sir, i can program the time bt i cant save it.keeps on going back to default once i turn the keys off. how do we save the settings sir?thanks
I'm very confused! I have a 1 cylinder motorcycle. I am very interested in the RPM counter displaying correctly at whatever speed it is. But in the options it only has a 2 and a 4 ..... where is the 1? Can somebody help me? I don't want to waste my money on something that doesn't work for me and feel unsatisfied! Those who have this and have only 1 cylinder works?
I would put it on the two and not worry about it. It has a lot of room to set your speed, if you use a GPS speed app on your phone there should plenty of room to set your speed. I don't think the amount of cylinder has anything to do with matching the speed rotation of your tire.
Nice one mate
So if a bike gets signals from the ecu will this work with it?
di you mean samDo ?
i ordered a identical model from another brand and it sucks cant even enter the setup.
i can find a similar one but its not sambo but samdo ?
thanks for your video its amazing !
It actually was a Sambo digital speedometer, I had bought it off Amazon. If you search Sambo Digital Speedometer it shows up on Wish now and a few other places. Thanks!
@@projectnext5020 thanks for the reply. unfortunatly amazon ebay wish even google doesnt give any decent result for a samBo speedometer. thank you anyway
you do not connect the gears of speeds from 1 to 5 in it? in the video you can't see the numbers turning on when you set the speeds.
My bike does not have a gear indicator so I cannot use the indicator lights.
How's the visibility? I feel that reflections would make it hard to read I think outdoors in daylight (when 90% of its use will). I am considering one as a cheap and easy way to replace the broken mechanical gauges on an old bike.
Never crossed my mind so I guess it's good to go!
Bonjour
Merci pour les informations déjà fourni et il me reste des questions
Comment mettre en 1 cylindre deux temps ??
Comment régler la valeur du compte tour ??
Je suis français et je ne parle pas anglais je passe donc par un traducteur
Cordialement
Hello
Thanks for the information already provided and I still have questions
How to put in 1 cylinder two times ??
How to set the value of the tour account ??
I am French and I do not speak English so I go through a translator
cordially
✋️Salut ✋️
ruclips.net/video/SqlIyr1mmeE/видео.html
I just ordered this meter for about $26 , postage included,
AliXpress
What are you putting it on? once it's mounted its easy to get set to the right speed, you may be able to use just one magnet and go buy a $12 3/8 Cobalt bit to drill the hardened brake disk.
@@projectnext5020 you mean the "hole" will "replace" 2nd magnet?👌
Well done a great help I’m just struggling with which colour wire is supposed to go to coil for rpm to work and also neutral light too it’s scrambled my brains all day An would really appreciate your help plz
Blue and Yellow, 8:14 on the video. I could have stated that better. good luck!
Project Next I done that and wired it direct to coil and nothing 🤷♂️ there’s 2 wires and I tried both ...I’ve also put voltmeter on the blue yellow wire and there’s nothing shows 0 volts I’d assume they must be something coming from it when bikes running could you confirm plz? Cos it’s kickin my ass
Awesome video exactly what I was looking for thank you so much, did you get the temperature to display I can’t figure that out ?
Hello. Did you figured out about the temperature to display?
Do you know if it works with a 2 cylinder bike with 4 spark plugs?
Hello... congratulations...can you tell me please about the neutral shift?i cant fix it.and the fuel is flashing all the time.pleaee save me.thanks a lot
did you solved it? if yes, how?
Pretty sure that brand name is frowned upon
should I remove it ?
@@projectnext5020 meant the mis spelling in the video title
@@prawny12009 OK ..Probably so, I was so frustrated trying to get this vid up, I was thinking about not even finishing it. It ended up being too long and drilling through the brake disk was a nightmare. I didn't really understand what you were saying. Have a good one!
Hi great video! I have the same speedometer trying to install it on atv Suzuki Ltz 400 everything goes good except the gears I don’t know how to wire them up pls help. Thanks
Well my bike does not have any way to get a shift indicator so I'm a little jealous of your problem. there should be a cable with multiple wires wrapped together coming from your case close to the front sprocket. That is where you need to start. As far as mapping the shifting out I would prefer to be there as opposed to guessing...sorry.
Thank you for your video, helped me alot, but I have some open questions with mine (13.000 rpm, 6 Gear (gears shown in the display)).
When we are bridging blue-white (fuel), it will show full but will this not destroy the speedometer in future because of permanent signal?
My speedometers config was stock 035 12 in the video 17:38 you are talking about 2 is single cylinders and 4 multiple cylinders but isn't it for 2-Stroke or 4-Stroke Engine for the correct rpm calculation?
Probably but the paperwork I had said cylinders. probably lost in translation. I just made sure the speed matched. Thanks for pointing that out I couldn't figure why they said cylinders... this stuff helps the community all is welcome here!
Two cycle or Four cycle very clever it makes sense to me thanks I will test that theory.
Sir, does the fuel gauge work if the bike dont have fuel gauge indicator like honda xr?
If you don't have a fuel gauge in the tank you'll need to put power to the fuel indicator wire on the Speedometer otherwise the fuel level will keep flashing at you as if it is low on fuel. I show this somewhere in the video.
@@projectnext5020 thank you for the info sir, we already solve the flashing, another question is it possible to put a gear indicator?
@@projectnext5020 same problem with mine sir!like how many volts? Is it 12volts?thankyou!
Hi,
Has anyone fitted this unit to a bike without a battery? I’ve fitted it to a crf450 but obviously can’t store the settings. What is the best way to get over this problem?
Thanks.
Try putting a smoke alarm battery in place of the always on and the ground pin
I'm putting it on a Royal Enfield Thunderbird 2009. It have a mechanical odometer, electronic techo, & fuel gauge.
Can I fit OEM speed sensor with some modifications? , Instead of the magnets. Please advise
Are you trying to keep the mechanical odometer? it has a odometer built in that uses the same electronics the speedometer uses.
@@projectnext5020 no
Any idea how to fix the background color ?
anyone tried hooking this up to a 2 stroke moped? im especially interested if rpm gauge will work. it has an AC type magneto iginition system, so actual power for the gague will have to bo transformed to dc.
Is it a bicycle with a engine?
All magnetos are ac regulator/rectifier converts to DC and controls voltage.
I installed on my yamaha xtz, but where i put the sensor for speed?. Shall i put on the pinion gear or make a bracket down on the front suspension?.
I made a bracket, I drilled and set the magnets in the brake disk and placed the sensor below the brake using the brake caliper bolt. pics at the end of the video.
@@projectnext5020 thanks alot man.
Thank you so much for the video.. What is the purpose of the magnet?🇵🇭
Wheel speed sensor. The other side picks up the magnetic field as it passes by and sends the signal to the tach. Use both magnets spaced at opposite sides of the wheel
hi . where did you tap the wires so that the clock will not reset every after turning off the motorcycle?
Funny you mention that, I've had to reset the clock twice, I just checked it and it's on time today. I think I might not have a good connection to the red wire and as the bike shakes it may loose contact for a second. It's the same place I have my USB port tied to and have had no problem with it. That is why I think I might need to go in and secure my connection again.
Hi mate I've finally wired it up
1 lights work
2 turn left&right works
3 full beam works
Now the bad part as soon as I put it in gear it is like I've turned the key on/off any ideas still need to work out the gear numbers cheers Paul
That sounds odd, It sounds like something is causing a short, disconnect the constant power and see if it stays on when shifting in gear. I can't see how putting in gear is causing it?
@@projectnext5020 hello right all wired up and working changed the wires happy days
NOW THE SPEEDO doesn't work when I bought this it comes with magnet but nothing like the ones you have fitted any ideas cheers for all the help Paul
ruclips.net/video/hwDlgqMCYok/видео.html
Hi sir, im from the Philippines. I just wanna ask a few questions about the Rpm. Because there is some errors on my diagram. It says that yellow and blue wires are my flashers i guess? Thankyou sir!
Hi I recently installed one. Was you able to set the mileage do you can stay consistent with it?
Hi what was total time spent installation,? Thx
What happends when u disconnect the battery from the headunit?
Does it saves the Data or is it lost?
yes. it retains all the mileage information.
About the magnet on the disc, which side it should B facing?, Towards the sensor or opposite?
the side where you see the magnet and the aluminum ring holding the magnet should be facing toward the sensor . The side with the little clip goes in toward the center of the rim.
@@projectnext5020 thank you very much, there was no instruction manual with the meter
Did you leave the old speedo sensor in the wheel hub and just remove the cable? My cable only screws out 2 turns and stops.
I just removed the old cable and plugged the hole to keep out dirt.
@@projectnext5020 what did you use to plug it?
@@samuraikido I used black electrical tape and rolled it till it was big enough to push in fairly snug and then wrapped it on the outside with more tape. It's just a soft cover to keep loose dirt out so nothing too fancy.
I just installed this and I noticed the speed drops now and then does anyone else have that problem
Make sure the sensor is as close to the magnets as possible. My sensor quit reading so I picked one up on eBay and it worked just fine.
Thanks I will try that!
Did you put the magnets at opposite sides of the brake disk?
@@projectnext5020 The black wire terminal on the picture it says switch and the paperwork that it came with says lock is this the permeant live to wire the clock and memory?
with me, the clock always goes to zero when I turn the ignition off and on again, why?where can I get a readable manual?
Night Rider you need to find a wire that has constant power to connect to the clock wire. Your clock is getting it's power from the ignition...so ignition off, power off, clock reset.
@@richardtschida2321 clock? does this model have a clock or is he referring to the odometer. my question is if the battery is disconnected does the odo go back to zero
how to save the time? caus every time i turn it off the clock goes back to 12:00
I'm having the same issue , I'll see what I can come up with to fix it.
Hello sir, is there a free diagram when purchasing that type of speedometer through online?
Hi when you tapped into the coil for the rpm wich wire did you connet to the coil and where did the blue and yellow wire connext to , did you splice the blue and yellow to the coil ? Many thanks
Yes, The yellow and blue was the tach(RPM) wire. I connected it directly to the coil wire , Make sure you get the right wire...I didn't at first.
Im connecting ut to a bandit 650. It has a wire on the loom that is for the tacho rpm would you still bypass that? Thanks for the fast reply
no , if you have a wire for it hook it up, My bike didn't have a tach so I had to connect to the coil. Your bike was already setup to take a tach.@@jamesholroyd6055
Yeah i tried that but it isnt getting a reading lol. No worries back to the drawing board. Thanks agin for fast reply mate and forbthe video its been very helpful so far
@@jamesholroyd6055 Well you can pull your tank and spice a wire to the coil, It's a guaranteed fix. Good luck!
I was looking to install digital gauges on a scooter ! But I don't know how it would turn out with the gear selecter since a scooter has no gears any suggestions ? Still looking for the right set up !
The bike in the video has no gear selector. You can just set up the speed censer and tach.
@@projectnext5020 that's cool ! Speed sensor, tack , fuel, turn signal, brights ,oil gauge & temp . Sink it into the dash looking for a set less then 3 inches thick because everthing is so compacted into the scooter dash . But I can hook up them functions on the set you have ? Appreciate the info
@@just4kicks950 I seen a speedometer just like this one with a tach that had a top rpm of 8 or 10 thousand vs the 12k on this one...good luck!
@@projectnext5020 thank you for the info my friend. I got the trail tech on my dirt bike & it works great ! My big drawback on that no fuel indicator LOL. Hard to tell from all the options on Amazon. Trials & errors LOL
My main concern here is that my bike currently has 35k miles on it. Is there any way I can adjust this new cluster so as to not be misleading?
No. That would be a bad deal for people purchasing a used bike so they made it illegal
@@projectnext5020 but would it not be equally illegal for me to sell a bike with an new odometer that says 5k when the true mileage is closer to 40k? In any case thank you for the prompt reply.
@@Tugoose your supposed to divulge that in the sale somehow. I kept my old Odometer to give to them at time of sale just to cover my butt. Have you seen a car with a replaced motor...same scenario.
Does it permanently store how many miles you have done? I'm looking for a speedometer, but quite a few of them seem to reset after a couple thousand miles. Thanks for the in depth video too.
The Odometer does permanently store the miles you put on the bike.
@@projectnext5020 Awesome thank you, I think I'll buy one of these.
Just installed mine but still my fuel Guage appears empty.do we have calibration for that sir?.
Sorry for the late response , my bike don't have a fuel gauge so I grounded it to a power wire so it shows full.
@@projectnext5020 You cant ground something to a power wire. That.makes no sense. You grounded it to ground or earth. Put the wire on another power wire as you said would make it active. In other words going to power would be no different going to the fuel gauge wire itself.
@@JasonBohl Are you talking about the fuel sensor? If so... I put power to it to make the electronic gauge show full and quit flashing. Not sure what your meaning but that's what I was trying to do. My bike has no fuel sensor in the tank.
@@projectnext5020 My bike has no fuel level sensor either but when connecting the fuel level sensor wire to power, it only made it flash even more so and messed up my RPMS. Therefor I put the level sensor to the ground d wire going to the speedo and now it simply shows full and stops flashing. Putting the fuel level sensor to the power wire is not the answer if you want it to shut up. If you put it on your green ground wire itll stop flashing and just show full all the time which is fine with me
Better then having it flashing all the time.
@@JasonBohl I'm going off memory so I'm sure you are right. That was the same thing I was going for...no flashing. At the time of making this video I couldn't find any info on this speedometer and tried to do it justice but the end goal was to get it on the bike asap. Good luck with your project!
Hello sir how to set the time
So I have the same bike so we can’t use the fuel or the gearing correct?
Down by the front sprocket is where the gear selector is located, I took out a cap like cover that was held in with a screw, unfortunately there were no gear contacts under there.
If you keep your same tank you'll be without a fuel gauge, You could buy one from RPS that fits the Hawk that has the fuel sensor cut out and you could then buy the sensors also. For the money I think I stay old school and just check the fuel by eye.
Hi, good pm will this fit a ninja 250r?
Does it come with rpm sensor?
Hi! You are very good! Can you help me please? I have the same tachi and i want to attach to a Gilera dna 50..im really go mad! Can you help me please to cable managing? If i give you a email can you help me?
Can i use this as replacement for my DUKE200 speedometer?
This is using a electronic sensor and a magnet to calculate speed. If you bike has a mechanical speedometer then you may want to find a original replacement. You can use this on any bike but there is much more involved if you watch the video.
What is the GPS app on your phone please
I use GPS Speedometer and Odometer by Cool Niks on the play store but any app will work.
My Bike Hero Glamour this meeter attached?
It should work on any bike. the speedometer reads from your front wheel and can be set to just about any size.
So what function were you unable to use on this cluster ? Total time for install?
Temp, gear selection and fuel. Id say in total it could be done in a day but I had to map out the wiring and figure out how to mount the sensor and as you seen I screwed up on the top bracket. Now That I know what to do I could easily knock it out in a day.
Shane are you a member on the forums at www.chinariders.net ? If not you need come hang out with me and these guys, a lot of great info and a lot of stuff from other China bikes cross over to the Storm. Bashan Brozz, RPS Hawk, TT250 ect.. All kinds of modding going on and great basic info to the most advanced stuff like porting and carburetion.
Great video
But This speedo 13k ref counter it’s really for 2 and 4 cyl The 10k ref speedo it’s better to show rpm for 1cyl -but I’ve bought the same 13k for my 1 cyl, ;(
042 it’s for wheel setting but not sure how -I believe it’s for distance of sensor from centre of axle -can you check if your sensor it’s about 17cm from it please ) as 17 works for you
Then number 12- 1-5 it’s setting for fuel sensor resistance 1=100 ohms 5= 500 ohms
2-4 2 =2cyl , 4=4cyl
does this tachometer not work for 1 cylinder?
@@jomarmarquez2448 it will work but may not show real rev _ but looks cool