Job done once again by a legend SandBlaster. Mick Blackley Sandblasting 👍👌.love ya work mate and determination. All the best from Australia mate 👍 🇦🇺🏴
The ball and chain? I've wanted this style for so long but near impossible to find in the UK and if you can find it it's well over £300 that's why it tuck me so long to get 1 I had this shipped from half way round the world 😂
I'm not sure 😂 I could say the same about makeing the videos I like the process I know im never going to be a video editor for a living but it's a nice hobby that I can share and people enjoy watching nice platform for everyone involved 😉
Yeah just a little hiccup I believe its a O ring on the elbow out of the filter housing letting air into the derv line then the computer spotting a fault then going into safe mode (bit like limp mode)
That depends on the workload your planning on taking on some pots are more suited for other things its like buying a car they all move people about just that some have luxury and and carry more people 👍
@@Mobileblaster Would they forward some photos that you could add to the end of the video? Depends how long you have them in edit before they a released I suppose!
Love the videos as I've got a pot blaster that I'm trying to set up to do two trailers like this one on my property. Any guess how much abrasive you used on this fuel trailer? I'm assuming that i should go with slag or something other than glass bead to get off the rust... But estimating the amount of material would be super helpful if you can. Thanks so much.
I used crushed glass as I buy bulk that's the cheapest for me but iron silicate is around the same price to private use and would cut slightly quicker but like I say glass to me is near half price it doesn't cut 2xs as fast so I opt for crushed glass cfm would pay a massive part in media and derv consumption
I'm fully dry all the time I keep things so stress free by adding water right at the end with a Win nosel keeping water well away from the pot altogether or at least try to keep it dry 😏 damp air is my issue now as this new to me compressor doesn't have a factory cooler like my old 1 and I regret not holding out for 1 with a cooler now 😬
The new 1 has got a long way to go as the older rig served me for a good 5 years without issues only its last few months it was becoming a problem and this newer to me rig has to do alot more work to justify its perches 👍 time will only tell 👍
Looks like it's something to do with the diesel fuel filter I believe its the O ring on elbow letting air into the system then the computer picking up a fault then dropping into safe mode(limp mode) I dropped the pickup pipe into the tank bypassing the filter housing and it seems to lay in that and its a new housing only old part is the elbow and only serviceable part is the O ring I still need to change it and try it but we'll time is a issue at the moment 😏
Love the work you do! Sounds like your sandblaster needs some TLC to get rid of those hiccups she's having lol. Question: Have you thought about switching over to those portable laser cleaners? Or adding one to your repertoire, alongside the sandblasting? From what I've seen, they're pretty nice bits of kit that can even expand the jobs you can offer - like if a customer wanted paint removed but _not_ the underlying primer layer (I _think_ those laser cleaners can have their settings altered to do this?? Not sure though). Or removing soot from fire/smoke damaged properties.
😂 yeah always something going wrong lol what I've sussed out is anything a laser can do a blaster can also do but a blaster is 100x cheaper to buy and 10x cheaper to operate 10x faster at operating plus a blaster can do alot more. I would love for the technology to improve as I think it will be the future of serface preparation but as it stands alot is needed to make it feasible option for a business to buy
No way would any mobile lasers do this job even the extra large more power hungry units couldn't come close to the speed finish and cost of a blaster 👍
@@Mobileblaster Ah fair enough. I wasn't sure since I'd seen they appear relatively fast, from the videos I've watched. I kinda got obsessed with them of late and been binging a _lot_ of laser cleaning videos lol 😁Same thing I've been doing with your videos too :) It's very satisfying to watch!!
Yea the lasers are good for smaller parts indoors, inside factories and that. Is there a secondary screen or something in or around the fuel pump that might be blocked. Something before the fuel filter maybe. Just guessing. It's a nice compressor Doosan makes pretty reliable gear too. How many hours you got in it now.
The have alot of equipment for sure 👍 I've been doing his stuff since aprox 2016 every 2 year ish his dumpers get a fresh coat with a fleet of 25 its a nice steady number 👌 👍 plus all the other stuff 😊👌👍
![Best Oddly Satisfying Video❤️🔥[EP102]#Try Not To Say WOW Challenge❤️🔥Amazing People And Tools.](http://i.ytimg.com/vi/Z3nfpcR0Zzc/mqdefault.jpg)
Always very good work! You honor the profession of sandblaster
A colleague from France
😊 in the blast hood together 👌👍
Job done once again by a legend SandBlaster. Mick Blackley Sandblasting 👍👌.love ya work mate and determination. All the best from Australia mate 👍 🇦🇺🏴
My man Scott 💪 in the blast hood together 😊👌👍🏴🇦🇺
@Mobileblaster cheers mate 👍 👌 🍻
Good job and hard work I like the safety plug set up
The ball and chain? I've wanted this style for so long but near impossible to find in the UK and if you can find it it's well over £300 that's why it tuck me so long to get 1 I had this shipped from half way round the world 😂
Thanks for your time and consideration top job looking awesome 👍😎👍😎
Thank you 😊 👍😎
Satisfying work. Does a great job.
😊👌👍
class, Machine still treating you well I see, nice one Mick
Yeah decent unit this 😊👍👌
Why do like watching so much. Thanks for sharing
I'm not sure 😂 I could say the same about makeing the videos I like the process I know im never going to be a video editor for a living but it's a nice hobby that I can share and people enjoy watching nice platform for everyone involved 😉
Looked ruined at the start but skipping to the end looks class, Machine still treating you well I see, nice one Mick
Yeah just a little hiccup I believe its a O ring on the elbow out of the filter housing letting air into the derv line then the computer spotting a fault then going into safe mode (bit like limp mode)
Good job . I've just got a atlas copco xas 47 compressor.what kind of sand blaster would suit it ?
That depends on the workload your planning on taking on some pots are more suited for other things its like buying a car they all move people about just that some have luxury and and carry more people 👍
Be great to get photos of the items after they have been painted again
Yeah it would be nice to see but I'm never about after the blasting is done 👌👍
I thought that was some of the long boats
@@Mobileblaster Would they forward some photos that you could add to the end of the video? Depends how long you have them in edit before they a released I suppose!
I'm just wondering about the underside which you didn't blast.
How do you know I dint blast it? nearly impossible to film the underside 😎 but your right I didn't do the underside haha
blackley blasting Beautiful :)
😊👌👍
Love the videos as I've got a pot blaster that I'm trying to set up to do two trailers like this one on my property.
Any guess how much abrasive you used on this fuel trailer? I'm assuming that i should go with slag or something other than glass bead to get off the rust... But estimating the amount of material would be super helpful if you can. Thanks so much.
I used crushed glass as I buy bulk that's the cheapest for me but iron silicate is around the same price to private use and would cut slightly quicker but like I say glass to me is near half price it doesn't cut 2xs as fast so I opt for crushed glass cfm would pay a massive part in media and derv consumption
@@Mobileblasterthanks so much for the info.
Any chance you'll start showing the final look of the equipment after it's painted? It's very interesting how it will look in the end
I understand it would make for a good video but as a business I cannot hang about 😏 wait till the next upload I do the painting 😎👍
Nice job, which blast media did you use.
I use mostly crushed glass and iron silicate 👍
Looks great mick, well I saw your video doing wet blasting. How you connect that doing it with your dry blast system?
I'm fully dry all the time I keep things so stress free by adding water right at the end with a Win nosel keeping water well away from the pot altogether or at least try to keep it dry 😏 damp air is my issue now as this new to me compressor doesn't have a factory cooler like my old 1 and I regret not holding out for 1 with a cooler now 😬
@@Mobileblaster
thanks mate for reply :) keep shining
@akaalautopaint3371 your welcome thanks for watching 👌👍
Do these big blasters run at around 90 psi like the small cabinet ones, just at higher volume rate or do they run at higher pressure as well?
125psi @ 425cfm cabinets normally run 90 because the cfm (flow) is about 3hp = to 15cfm ish
Can you explain your setup? at the nozzle side of the hose what's going on there?
I get it now yeah 7:33 did you make that yourself?
No it was sent from half the way round the world we cannot get this type in the UK 👍
Ever thought of after blasting offer to put a layer of primer to initially protect the exposed metal ? Very good job, and great video 👍
I only do the blasting I'm not interested in doing paint although I do occasionally do it for myself or friends 👍
Has the bigger compressor been better over the previous
The new 1 has got a long way to go as the older rig served me for a good 5 years without issues only its last few months it was becoming a problem and this newer to me rig has to do alot more work to justify its perches 👍 time will only tell 👍
What type of grit are you using? No video of you painting it?
Crushed glass on this and no sorry I try to steer away from the painting side of things although I do sometimes do show painting on some jobs 👍
Какая производительность компрессора? Сопло какого диаметра?
425cfm @ 125psi 👍
Did you solve the compressor going into limp mode then?
Looks like it's something to do with the diesel fuel filter I believe its the O ring on elbow letting air into the system then the computer picking up a fault then dropping into safe mode(limp mode) I dropped the pickup pipe into the tank bypassing the filter housing and it seems to lay in that and its a new housing only old part is the elbow and only serviceable part is the O ring I still need to change it and try it but we'll time is a issue at the moment 😏
Good.job😄👍👍👏👏👏Nice😍
Thank you 😊
Hola Mick. Cual es la boquilla adecuada para un compresor de 125 cfm? Saludos desde Argentina. Suscripto
I believe its a #4 my 140cfm ran #5 and my 180cfm was a #5
@@Mobileblastergracias!
@@tetegirola94 👍
Nice to have a variety I just blast new tippers
Yeah they can get repetitive that's why I love my job it's something different every day 👌👍😊
Muito bom o trabalho.
Mais aqui no Brasil é proibido usar jateamento com areia .
It's also been banned since the 60s hear in the UK sandblasting as a name has stuck we actually use approved media's that's none toxic👍
I would guess those pipes are from a 70's RD 350 Yamaha? Good Job Mick! Cheers
Oh I don't know but he was well chuffed to see the stamp saying genuine and it had a motor sport name but I totally forgot what it said now 😊
@@JP-hr7ch only off by a few years. those old two smoker strokers are real cool. cheers!
Hi new the Chanel where sand go as not seen u top up ?
Into a presure pot in the van 🙂 bit like a hopper/egg timer thing 👍
Love the work you do! Sounds like your sandblaster needs some TLC to get rid of those hiccups she's having lol. Question: Have you thought about switching over to those portable laser cleaners? Or adding one to your repertoire, alongside the sandblasting? From what I've seen, they're pretty nice bits of kit that can even expand the jobs you can offer - like if a customer wanted paint removed but _not_ the underlying primer layer (I _think_ those laser cleaners can have their settings altered to do this?? Not sure though). Or removing soot from fire/smoke damaged properties.
😂 yeah always something going wrong lol what I've sussed out is anything a laser can do a blaster can also do but a blaster is 100x cheaper to buy and 10x cheaper to operate 10x faster at operating plus a blaster can do alot more. I would love for the technology to improve as I think it will be the future of serface preparation but as it stands alot is needed to make it feasible option for a business to buy
No way would any mobile lasers do this job even the extra large more power hungry units couldn't come close to the speed finish and cost of a blaster 👍
@@Mobileblaster Ah fair enough. I wasn't sure since I'd seen they appear relatively fast, from the videos I've watched. I kinda got obsessed with them of late and been binging a _lot_ of laser cleaning videos lol 😁Same thing I've been doing with your videos too :) It's very satisfying to watch!!
@DavidStruveDesigns 😂 if you look all the finishings they are removing are selected peaces and all very easy to do with a blaster 😬👌
Yea the lasers are good for smaller parts indoors, inside factories and that.
Is there a secondary screen or something in or around the fuel pump that might be blocked.
Something before the fuel filter maybe. Just guessing.
It's a nice compressor Doosan makes pretty reliable gear too.
How many hours you got in it now.
What mate, no underside blasting? just kidding, looks very satisfying.
His customers only want the bling factor, including boats
Glass back 😏 I do have videos of the underside of boats but they are very hard to film and turn out crap so I usually don't bother filming 👍
Old Jakto been going some years now.
Yeah really big firm 👌 and to be fair the old man is a really nice bloke 👍
🎉🎉🎉😊
😊👌👍
Rust car ?
I do have a car blasting just down my list of videos 👍
Slow work. Hard work. Hope it pays well. Gotta be sore
If you can show me a method that's faster I'm open to invest as like you say its hard work 😬
Never stops conking owt
😬 worked to the limits 😆
😂@@Mobileblaster
👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷Brasil
😊👌👍
"Nice easy project today" 🤦♂ Noooo don't say that 😁
Haha kinda jinxed myself then the compressor pays up a little 😬 I need to stop sating easy day 🫣😂
"Promosm" 🤪
😆😎
Jakto will keep you busy they've got some right shite
The have alot of equipment for sure 👍 I've been doing his stuff since aprox 2016 every 2 year ish his dumpers get a fresh coat with a fleet of 25 its a nice steady number 👌 👍 plus all the other stuff 😊👌👍
Is that the Defender quiet nozzle?
No it's just a standard 850 (I believe you guys size them #8)
Nice
@@TheMobileBlaster 👍